Canon Canovision8 E50E Service Manual page 154
8mm video camera & recorder
Table of Contents
3-17
Coaster
(Right),
Drive
Gear
(Right)
@ Disassembling
(Fig.II-24)
\
(1)
In the
same
procedures
"3-3"
and
"3-12",
dismount
the
capstan
motor
and
the
drum
unit.
(2)
In the
same
procedures
in "3-14",
take
off
the
loading
lever.
(3) Set STOP mode.
(4)
To take
off
the
coaster
plate
spring @ and the
coaster
(Right)
©,
xemove
the screw @.
(5) To detach the plate TT ©, remove the two screws @.
(6) To dismount
the drive gear
(Right)
@,
remove
the' washer © (#1.5).
\
*® Reassembling
(Fig.1II-24)
*Caution:
Do not turn the tilt adjusting
screw © of coaster
(Right). (Repair
parts
have
been
already
adjusted.)
(1)
Apply
the
grease
to the
indicated
positions
of
chassis
as
shown
in Fig.A.
(2) Apply the 1/2 drop of oil to the shaft ©.
(Fig.F)
a
(3) Apply the grease
onto the pin @, the shaft @ and the dowel @ of coaster
/
(Right) ©.
(4) Assemble the pin @ and the shaft @ aligning the slot @ of chassis.
(5) Put the brake releasing arm @ to the arrowed direction @.
(6)
Install
the drive
gear
(Right)
@ to the
shaft
@.
Then.
mesh
it with the
drive
gear
(Left)
@ while
aligning
each
phases
as
shown
in Fig.B.
(7) Align @ with @, the hole @ with the pin © of coaster
(Right) @, respec-
tively.
(8)
Secure
the washer
© (91.5).
(9) Assemble
the coaster
plate
spring @ while aligning
the shaft
@
(coaster
)
@)
with
the pin ©.
Then,
secure
it with the screw @.. (Torque:
500g/cm
approx) .
(10)Assemble
the plate TT @ aligning
with the dowel
®.
Then,
secure
it with
the two
screws
@ in numerical
order.
-
(11) Apply the grease
to the positions
indicated
in the
Fig.C
and E.
(12)In
the
same
procedures
in "3-14",
install
the
loading
lever.
({13)In the
same
procedures
in "3-12"
and "3-3",
mount
the
drum
unit
and the
capstan
motor.
*Note:
After
reassembling,
perform
the tape
path
adjustment.
od
,TT
erease,
;
Oserexe @Praees Trew
{@
10mm-15mm)
wa
coaster
plate
@spring
Petre
S—1@
Washer (91.5)
yo S@pare
!
A
|
4
+
@slot
Aliga the holes
¢
aN
pei
Rami
,
2
i
@part
Mesh grooves!
Ny
ca
"
;
"=-@shart
OQ
|NAL
|
&
Drive gear
\
|!
SS.
(Right)
_@ Drive
gear
\
<
releasing
arm
\
—
ig. p (left)
i
5
Coaster
(Right)
Fig.II-24
Hide quick links:
Chapters
Table of Contents
Need help?
Do you have a question about the Canovision8 E50E and is the answer not in the manual?