Table of Contents
Advertisement
ART 5W/GTWIN MONITOR
CHARACTERISTICS
- Monitor for Gtwin installation.
- 5" TFT colour screen.
.
- Wi-Fi
transmission monitor to call transfer to mobile
transmission. (
power supply unit 1723/22 required for apartment if
always active in the building see
- Monitor with simple installation (non-polarised 2 wire BUS).
-
Function and programming access buttons (customise monitor functions)
- Completely private conversation and image.
- Auto-spy function.
- 'Doctor mode' function (automatic door opening
- "Do not disturb" mode function.
- Intercom between two devices in the same apartment (programmable).
.
- Intercom between two devices in different apartments (programmable).
- "HZ" input for calls from apartment front door .
- Call volume control (maximum,
- Output to auxiliary call repeater.
- Different ringtones to identify call origin: Main door panel, slave door panel, intercom and interior door of the
apartment.
- Adjustments on screen display:
-
Allow communication in ' ush-to-talk' mode or
-
SW1
configuration switch
.
- SW2
configuration switch
.
- JP3 jumper(end of line).
- Push
Button for activating the main door release and
- Notification leds.
SYSTEM OPERATION
- To make a call, the visitor needs to press the button for the apartment, an audible tone indicates that the call is being
made and LED
on the door panel illuminates. At this moment, the apartment's monitor(s) receives the call. If the visitor
presses the button for another apartment by mistake, the call can be cancelled by pressing the button for the correct
apartment.
- In systems with several access doors, the other door panel(s) will automatically disconnect; if another visitor wishes to
call, LED
on the door panel will blink for 3 seconds. If the vocal synthesis module is installed on the door panel, the
message 'communicating' will indicate that the channel is busy.
- General panels (main): If the call is being made from the general panel, the interior panel of the building being called
and other possible general panels automatically disconnect; if another visitor attempts to call from either a busy interior
panel, an audible tone will indicate that the channel is busy and LED
another general panel, an audible tone will indicate that the channel is busy and LED
for 3 seconds. The door panels of the other interior buildings will remain free to be used.
- General panels (main): If the call is made from an interior panel, the other interior panels will remain free to be used. It is
only possible to make calls to interior buildings from the general panels when their door panels are not in use; if an attempt
is made to make a call to a busy interior panel, an audible tone will indicate that the channel is busy and LED
of the general panel will blink for 3 seconds.
- The call lasts for 60 seconds, during which time an image appears on the apartment's master monitor after the call is received
without the visitor knowing, and the indicator LED and status LED
To view the image on a slave monitor, press button
call is not answered within 60 seconds, the indicator LED and status LED
LED
on the door panel will turn off and the channel will become free.
- To establish communication, press button
illuminate and LED
- Guaranteed communication time is 90 seconds (configurable); after 90 seconds of guaranteed communication
time,the channel will become free.
- To end communication, press button
will turn off and the channel will become free.
- To open the main or secondary door, press the corresponding button
one press will activate the lock release for 1 second (configurable main door) and, with the opening of the main door,
LED
w
ill also illuminate for 1 second.
- A description of the function buttons can be found on p. 5.
,
32
to
35
pages).
medium and
brightness
, contrast, colo r
P
CODE
:
Dip2 to Dip8
INT
: to set the monitor as master / slave 1, slave 2 or slave 3.
of the monitor, status LED
of the door panel will turn off.
, and the monitor's indicator LED and status LED
smartphone.
minimum
.)
u and communication
ermite
modo de funcionamiento "pulsar para hablar" o "manos libres".
to set the monitor address "call (user) code".
push
button for activating the secondary door release.
of the master and slave monitor(s) will illuminate (green).
and the image disappears from the monitor that was displaying it. If the
Only the master monitor can activate Wi-Fi
there are more than
.
volume.
of the door panel will blink for 3 seconds, or from
of the general panel will blink
of the master and slave monitor(s) will turn off.
will blink (green), LED
/
during the call or communication processes:
24 monitors
with
WiFi
of the door panel will then
and door panel LED
3
Advertisement
Table of Contents
