Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for PE micro TRK-USB-MPC5604B
- Page 1 Arrow.com. Downloaded from...
- Page 2 Purchase Agreement P&E Microcomputer Systems, Inc. reserves the right to make changes without further notice to any products herein to improve reliability, function, or design. P&E Microcomputer Systems, Inc. does not assume any liability arising out of the application or use of any product or circuit described herein. This software and accompanying documentation are protected by United States Copyright law and also by International Treaty provisions.
-
Page 3: Table Of Contents
OSJTAG Bootloader Enable ................6 TRK-USB-MPC5604B CODE DEVELOPMENT SOFTWARE......7 Using CodeWarrior With The TRK-USB-MPC5604B ........7 Using P&E Software With The TRK-USB-MPC5604B ........8 TRANSITIONING TO YOUR OWN TARGET ..........8 Hardware Solutions At A Glance..............8 Working With P&E’s Multilink Universal or Multilink Universal FX ....10 Working With P&E’s Cyclone MAX .............. - Page 4 TRK-USB-MPC5604B Is Undetected ............12 TRK-USB-MPC5604B EVB User Manual Arrow.com. Arrow.com. Arrow.com. Arrow.com. Downloaded from Downloaded from Downloaded from Downloaded from...
-
Page 5: Introduction
The TRK-USB-MPC5604B is a low-cost development system supporting Freescale MPC5604B microcontrollers in 100LQFP packages. The Embedded OSJTAG circuitry on the TRK-USB-MPC5604B board allows the processor on the board to be debugged and programmed via USB from a PC. In addition, the demo board can be powered using the USB bus. -
Page 6: Hardware Features
JTAG port is provided to allow the use of an external Qorivva MPC55xx/56xx interface such as P&E’s USB Multilink or Cyclone MAX automated programmer. P&E’s USB Multilink provides faster communication speeds and can be used to debug both the TRK-USB-MPC5604B and the user’s own targets. Note: The DEMO board’s Embedded OSJTAG is intended to function with the on-... -
Page 7: Trk-Usb-Mpc5604B Jumper/Connector Quick Reference
Figure 2-1: Top Component Placement TRK-USB-MPC5604B Jumper/Connector Quick Reference Default Jumper Settings The following is a list of default jumper settings for TRK-USB-MPC5604B board. The settings listed indicate the “on” (or installed) position. Default Jumper Settings JUMPER OPTION SETTINGS DESCRIPTION... -
Page 8: Getting Started With The Trk-Usb-Mpc5604B
The Embedded OSJTAG driver is required to operate the TRK-USB- MPC5604B using a PC. The Embedded OSJTAG driver should be installed before the PC is connected to the TRK-USB-MPC5604B. This driver can be found at freescale.com/TRK-USB-MPC5604B, or at http://www.pemicro.com/ osbdm. -
Page 9: Operating Modes
“Found New Hardware Wizard.” If the TRK-USB-MPC5604B hardware interface driver is now properly installed on your system, the green USB LED on the TRK-USB-MPC5604B should be illuminated. In addition, if you turn on the system power of the TRK- USB-MPC5604B you will see the yellow Power LED illuminate. -
Page 10: Run Mode
Qorivva software tools will work with the TRK-USB-MPC5604B. Please refer to Section 7 - TRK-USB-MPC5604B CODE DEVELOPMENT SOFTWARE for more information. Run Mode The TRK-USB-MPC5604B’s rich component list empowers it to perform a variety of tasks. Once an application is developed, debugged, and programmed properly into the microcontroller’s internal flash memory, it can... -
Page 11: Trk-Usb-Mpc5604B Code Development Software
The TRK-USB-MPC5604B includes P&E’s OSJTAG circuitry, so no external Qorivva hardware tool is needed to debug and program the TRK-USB- MPC5604B. A user only needs to connect the TRK-USB-MPC5604B to their PC to start developing code for it. The TRK-USB-MPC5604B package comes with a special edition of Freescale’s CodeWarrior studio. -
Page 12: Using P&E Software With The Trk-Usb-Mpc5604B
TRANSITIONING TO YOUR OWN TARGET Once you have finished working with the TRK-USB-MPC5604B and are ready to build your own target, you will need a hardware tool to allow you to develop using your own board. - Page 13 Architecture PX Series, and ARM MAC7xxx microcontroller families • Communication via USB, Serial, and Ethernet Ports • Multiple image storage • LCD screen menu interface • Supported by P&E software and Freescale’s CodeWarrior TRK-USB-MPC5604B EVB User Manual Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com.
-
Page 14: Working With P&E's Multilink Universal Or Multilink Universal Fx
Codewarrior as well as P&E’s in-circuit debugger and flash programmer to allow debug and flash programming of the target processor. P&E’s Qorivva software includes a flash programmer, in-circuit debugger, Windows IDE, and a register file editor, and can be bundled with these interfaces. TRK-USB-MPC5604B EVB User Manual Arrow.com. Arrow.com. Arrow.com. -
Page 15: Working With P&E's Cyclone Max
Freescale’s CodeWarrior as well as development software from P&E. P&E’s Cyclone MAX is also available bundled with additional software as part of various Development Packages. In addition to the Cyclone MAX, these TRK-USB-MPC5604B EVB User Manual Arrow.com. Arrow.com. Arrow.com. -
Page 16: Troubleshooting
(B) USB Hub Usage The TRK-USB-MPC5604B is a high-power USB device. If a USB Hub is used, it must be a self-powered hub (i.e., with its own power supply). If the Hub is not self-powered the TRK-USB-MPC5604B will not work. In general, USB ports located directly on the PC are high-power (self-powered) ports. - Page 17 Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from...
Need help?
Do you have a question about the TRK-USB-MPC5604B and is the answer not in the manual?
Questions and answers