Related Manuals for Lantronix C3210-10 Series
Summary of Contents for Lantronix C3210-10 Series
- Page 1 C3210-10xx ION Gigabit Ethernet Media and Rate Converter Module 10/100/1000Base-T to 1000Base-SX/LX Install Guide Part Number 33414 Revision D August 2023...
- Page 2 C3210 Install Guide Intellectual Property © 2023 Lantronix, Inc. All rights reserved. No part of the contents of this publication may be transmitted or reproduced in any form or by any means without the written permission of Lantronix. Lantronix is a registered trademark of Lantronix, Inc. in the United States and other countries.
-
Page 3: Table Of Contents
Lantronix C3210 Install Guide Contents Product Description ............................4 Features ................................ 4 Ordering Information ............................. 4 Installation ..............................5 DIP switches ............................. 5 6-position DIP switch ..........................5 AutoCross jumper (J6) ..........................6 Hardware/software Mode jumper (J5) ...................... 6 Install chassis card ........................... 7 Install copper cable ........................... -
Page 4: Product Description
[10 km/6.2 mi.] Link Budget: 10.5 dB 10/100/1000Base-T (RJ-45) [100 m] to 1000Base-X SFP Slot (empty) C3210-1040 Optional Accessories (sold separately) See Lantronix full line of SFP transceivers on Lantronix webpage. Optional SFP Modules accessory; sold separately. * Distances listed are the typical maximum cable distances. Actual distance depends on the physical characteristics of the network these devices are operating on. -
Page 5: Installation
Lantronix C3210 Install Guide Installation CAUTION: Wear a grounding device and observe electrostatic discharge precautions when handling the SIC media converter. Failure to observe this caution could result in damage or failure of the SIC. DIP switches The C3210 has two DIP switches mounted on the PC board: a 6-position DIP (first set at left) and on some units, a 4-position DIP (second set to the right). -
Page 6: Autocross Jumper (J6)
Straight-through or crossover twisted-pair cable, depending on installed site devices, MUST be installed at EACH twisted-pair copper link. Note: The factory default is “A” (AutoCross enabled). Lantronix recommends leaving the device in the “A” (enabled) position. Hardware/software Mode jumper (J5) The hardware/software 3-pin header, J5 is located on the circuit board (labeled H and S in the figure to the right.) -
Page 7: Install Chassis Card
Lantronix C3210 Install Guide Install chassis card 1. Remove one chassis slot cover from the ION Chassis (keep the slot cover and screw). 2. Carefully slide the C3210 into the installation slot(s), aligning it with slot guides. 3. Ensure that the C3210 is firmly seated inside the chassis. -
Page 8: Install Copper Cable
Lantronix C3210 Install Guide Install copper cable Port 1: 10/100/1000Base-T Copper Port: 1. Locate a 10/100/1000Base-TX compliant copper cable with male RJ-45 connectors installed at both ends. 2. Connect the RJ-45 connector at one end of the cable to the 10/100/1000Base-RJ-45port (port 1) on the C3210. -
Page 9: Operation
Lantronix C3210 Install Guide Operation Status LEDs Use the status LEDs to monitor C3210 operation in the network. Power and fiber status LEDs The status LEDs for the 1000Base-X fiber connection (labeled LACT and PWR) are located next to the fiber port (Port 2). -
Page 10: Product Features
Lantronix C3210 Install Guide Product features Auto-Negotiation The Auto-Negotiation feature allows the C3210 to configure itself to achieve the best possible mode of operation over a link, automatically. The C3210 broadcasts its speed (10 Mbps, 100 Mbps, or 1000 Mbps) and duplex capabilities (full or half) to the other devices and negotiates the best mode of operation. - Page 11 Lantronix C3210 Install Guide Pause The pause feature is used to suspend data transmission temporarily in order to relieve buffer congestion. If a C3210 needs some additional time to clear network congestion, it will send a pause signal to the C3210 at the other end, that C3210 will wait a predetermined amount of time before re-transmitting data.
- Page 12 Lantronix C3210 Install Guide SNMP See the on-line documentation that comes with the FocalPoint software for applicable commands and usage. Use SNMP at the attached terminal or at a remote location to monitor the C3210 by monitoring: • Copper and fiber link status •...
- Page 13 Lantronix C3210 Install Guide IEEE802.1q VLAN tagging and double tagging (Q in Q) The 802.1q specification establishes a standard method for inserting virtual LAN (VLAN) membership information called a tag into Ethernet frames to break large networks into smaller parts, or to address security concerns.
-
Page 14: Cable Specifications
Lantronix C3210 Install Guide Cable Specifications The physical characteristics must meet or exceed IEEE 802.3 specifications. ™ Fiber cable Bit Error Rate: <10-9 Single mode fiber (recommended): 9 μm Multimode fiber (recommended): 62.5/125 μm Multimode fiber (optional): 100/140, 85/140, 50/125 μm... -
Page 15: Copper Cable
Lantronix C3210 Install Guide Copper cable Category 5 (minimum requirement) Gauge: 24 to 22 AWG Attenuation: 22.0 dB /100 m @ 100 MHz Maximum Cable Distance: 100 meters Straight-through or crossover twisted-pair cable may be used. • • Shielded (STP) or unshielded (UTP) twisted-pair cable may be used. -
Page 16: Related Information
(outside plant) link segments that are subject to lightening transients or power faults. Related Information A printed Quick Start Guide is shipped with each unit. For Lantronix Drivers, Firmware, Manuals, Product Notifications, Warranty Policy & Procedures, etc. go to the Lantronix Technical Resource Center. -
Page 17: Troubleshooting
Lantronix C3210 Install Guide Troubleshooting Is the Power LED lit? • Is the C3210 inserted properly into the chassis? • Is the power cord properly installed in the chassis and in the grounded AC outlet? • Does the grounded AC outlet provide power? •... -
Page 18: Compliance Information
Lantronix C3210 Install Guide Compliance Information Declaration of Conformity Manufacture’s Name: Lantronics, Inc. Manufacture’s Address: 48 Discovery, Suite 250, Irvine, California 92618 USA Declares that the product(s): C3210-1013, C3210-1039, C3210-1014, C3210-1040 Conforms to the following Product Regulations: EMC Directive 2004/108/EC; EN 55022:2006+A!:2007 Class A; EN 55024:1998+A1:2001+A2:2003;... - Page 19 In accordance with European Union Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003, Lantronix will accept post usage returns of this product for proper disposal. The contact information for this activity can be found in the 'Contact Us' portion of this document.
- Page 20 Toll Free: 800-526-8766 Phone: 949-453-3990 Fax: 949-453-3995 Technical Support Online: https://www.lantronix.com/technical-support/ Sales Offices For a current list of our domestic and international sales offices, go to the Lantronix web site at www.lantronix.com/about/contact. 33414 Rev. D https://www.lantronix.com/ Page 20 of 20...
Need help?
Do you have a question about the C3210-10 Series and is the answer not in the manual?
Questions and answers