Table of Contents
Advertisement
+, -
<PRO5>
Code setting
SET
SET
+, -
Display adjustment
setting
SET
<When selecting target setting>
+, -
+, -
Notes 6) Target setting of display adjust setting depends on the re-
+, -
"
"
Reset setting
SET
+, -
CUSTOM setting
SET
Hysteresis setting
Window comparator
mode
<PRO6> (Note 7)
Normal mode
(Except sensing output 2)
+, -
SET
+, -
Forced OFF
By pressing down MODE key long time,
output mode
sensing output 1 or 2 can be changed to
another.
+, -
Forced ON
output mode
+, -
<Window comparator mode or Hysteresis mode>
(The following diagram shows in selecting the window comparator mode.)
SET
Notes: 7) Set the sensing output setting after input / output setting for
8) After external input, the time given until an answer back output is as follows. How-
the following table.
2 point teaching
Limit teaching
Full auto teaching
+, -
Display adjust
Data bank loading
Data bank saving
9) Incident light intensity depends on the response time as table below.
Response time
"
", "
", "
"
", "
", "
Target setting
OFF
(Note 6)
+, -
+, -
+, -
Display adjustment
Target setting
0
setting
SET
SET
Changeable incident
light intensity in + or -
SET
SET
+, -
Incident light
intensity
sponse time as table below.
Response time
Target setting
", "
", "
"
From -1,999 to 4,000
", "
", "
"
From -1,999 to 9,999
Automatic
SET
<RUN mode>
Blink
Blinks 3 times
Response time
Light-receiving
Emission halt
setting
sensitivity setting
setting
+, -
+, -
+, -
+, -
+, -
Code setting
Data bank loading
setting
mode
mode
+, -
+, -
Self-diagnosis
Only displayed in
output mode
(Except sensing output 1)
+, -
Answer back output
mode (Note 8)
(Except sensing output 1)
Shift amount setting
(Displayed in percentage)
SET
SET
+, -
SET
+, -
Shift amount setting
(Note 9)
+, -
.
Input time
After 20ms from the input end, the answer back output is
read out when result of the teaching is "
After 20ms from the input end, the answer back output is
read out.
After 520ms from rising of last input pulse, the answer back
output (pulse) of the number of channel in the data bank is
read out.
Incident light intensity
"
Max. 4,000
"
Max. 9,999
+, -
<PRO7>
SET
SET
+, -
+, -
+, -
Hysteresis
mode
+, -
<PRO1>
".
Logic operation
Between adjacent
setting
SET
SET
+, -
Between external
input
SET
+, -
+, -
Between sens-
ing output 1 and
sensing output 2
SET
Setting of threshold
Setting of threshold
value tracking
tracking cycle
SET
SET
+, -
Sensing output
setting
SET
+, -
Storage cycle
+, -
setting
SET
+, -
Algorithm setting
(Note 10)
SET
Notes: 10) In case setting to "
the changed incident light intensity.
Shift direction of the threshold differs depending on the
combination of the sensing output status and the sensing
output operation.
Sensing output status
Sensing output operation
Sensing output ON
Sensing output ON
Sensing output OFF
Sensing output OFF
Invalid
and
+, -
+, -
+, -
+, -
xor
or
Invalid
and
+, -
+, -
+, -
+, -
xor
or
Invalid
and
+, -
+, -
+, -
+, -
xor
or
OFF
1 sec.
+, -
OFF
ON
+, -
OFF
1 time
+, -
Limit teaching
Auto teaching
+, -
", conduct the limit teaching for
Shift direction
Light-ON
-
Dark-ON
+
Light-ON
+
Dark-ON
-
Advertisement
Table of Contents
Need help?
Do you have a question about the LS-501 Series and is the answer not in the manual?