Toshiba TOSVERT VF-P7 Instruction Manual page 216

[25] Speed/torque reference gain/bias setup #2(2/2)
Communi
Title Function
cation No
Modulation rate control
0483

margin (voltage control)
Modulation rate control
 0484
margin (V/f control)
Stall cooperation gain at field
0485

weakening zone
0486 Exciting starting rate

 0487 Compensation coefficient for iron loss 0∼255
Voltage compensation
 0488
coefficient for dead time
 0489 Dead time compensation
0490 Dead time compensation (bias time) -3.27∼3.27

Current / voltage control
0491

switching frequency
[26] Secondary acceleration/deceleration
Communi
Title Function
cation No
0500 Acceleration time #2

 0501 Deceleration time #2
0502 Acceleration/deceleration pattern #1 0: Linear, 1: S-pattern #1, 2: S-pattern #2

 0503 Acceleration/deceleration pattern #2 0: Linear, 1: S-pattern #1, 2: S-pattern #2
Acceleration/deceleration
 0504
#1,2,3,4 selection
 0505 Acc/dec switching frequency #1 0.0∼ [Hz]
0506 S-pattern lower-limit adjustment amount 0∼50 [%]

 0507 S-pattern upper-limit adjustment amount 0∼50 [%]
0508 Acc/dec time lower limit

 0510 Acceleration time #3
0511 Deceleration time #3

0512 Acceleration/deceleration pattern #3 0: Linear, 1: S-pattern #1, 2: S-pattern #2

0513 Acc/dec switching frequency #2 0.0∼ [Hz]

0514 Acceleration time #4

 0515 Deceleration time #4
0516 Acceleration/deceleration pattern #4 0: Linear, 1: S-pattern #1, 2: S-pattern #2

 0517 Acc/dec switching frequency #3 0.0∼ [Hz]
※(Reference section): Refer to the inverter's individual manual.
* Minimum setup unit is 0.1 in case of 16-bit access. Sensorless vector/vector with sensor (
Adjustment range
80.0∼300.0 [%]
80.0∼300.0 [%]
0∼255
1.64∼327.6
0.00∼327.6
0: Enabled, 1: Disabled
10.0∼60.0 [Hz]
Adjustment range
0.1()∼6000 [s]
0.1()∼6000 [s]
1: Acceleration/deceleration #1
2: Acceleration/deceleration #2
3: Acceleration/deceleration #3
4: Acceleration/deceleration #4
0.01∼10.00 [s]
0.1()∼6000 [s]
0.1()∼6000 [s]
0.1()∼6000 [s]
0.1()∼6000 [s]
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
0.1/0.01 105.0 Enabled
●／―
0.1/0.01 105.0 Enabled
―
1/1 128 Enabled
●／●
0.01/0.01 163.8 Enabled
●／●
1/1 10 Enabled
●／●
0.01/0.01 3.90 Enabled
●／●
− 0 Enabled
●／●
0.01/0.001 0.00 Enabled
●／●
0.1/0.01 40.0 Enabled
●／―
Min. unit (panel/ Default Write during
Speed
communication) setting running
control
0.01/0.01* See J-28 Enabled
●/●
0.01/0.01* See J-28 Enabled ●/●
0 Enabled
− ●/●
− 0 Enabled ●/●
− 1 Enabled ●/●
0.01/0.01 0.0 Enabled ●/●
1/0.01 25 Enabled
●/●
1/0.01 25 Enabled ●/●
0.01/0.01* 0.10 Enabled
●/●
0.01/0.01* See J-28 Enabled ●/●
0.01/0.01* See J-28 Enabled
●/●
0 Enabled
− ●/●
0.01/0.01 0.0 Enabled
●/●
0.01/0.01* See J-28 Enabled
●/●
0.01/0.01* See J-28 Enabled ●/●
0 Enabled
− ●/●
0.01/0.01 0.0 Enabled ●/●
● −
:valid, :invalid)
Vector control
V/f Reference
Torque Position
Constant section
control control
― ― −
−
― ― ● −
●／● ―／● ●
−
●／● ―／● ―
−
●／● ―／● ― −
●／● ―／● ● −
●／● ―／● ● −
●／● ―／● ●
−
― ― ―
−
Vector control
V/f Reference
Torque Position
Constant section
control control
6.23.2
− − ●
− − ● 6.23.2
6.23.1
− − ●
− − ● 6.23.2
− − ● 6.23.2
− − ● 6.23.2
− − ●
6.23.1
− − ●
6.23.3
− − ●
− − ● 6.23.2
6.23.2
− − ●
6.23.2
− − ●
6.23.2
− − ●
6.23.2
− − ●
− − ● 6.23.2
6.23.2
− − ●
− − ● 6.23.2