Service And Adjustments; Replacing Auger Belt; Skid Shoe Adjustment; Lift Release Cable Adjustment - Craftsman 486.24838 Operator's Manual

CAUTION: Before servicing oradjusting
thesnow thrower s hut o fftheengine, r emove
thespark plug wire(s), settheparking b rake
andr_move t hekey from thetractor i gnition.
REPLACING AUGER BELT
• Disengage the tractor's attachment clutch.
• Lower the snow thrower to the ground.
•
Remove the attachment pin
• Lock the snow thrower's lift handle in the down
position to decrease belt tension
• Release the spring tension from the auger belt idler
arm on the bottom of the clutchddler assembly.
• Remove the auger drive belt from the clutch/idler
assembly and from the spgal auger housing
• Install new belt over top of large auger drive pulley
and under the two side idler pulleys Twist the belt 1/4
turn to seat the "V" of the belt in the groove of each
idler pulley. Refer to figure 55 on page 23
• Assemble the belt onto the clutch/idler assembly
SKID SHOE ADJUSTMENT
* The skid shoes are mounted on each side of the spiral
auger housing. They regulate the distance the scraper
plate is raised above the plowing surface. When
removing snow from a gravel driveway or and uneven
surface, it is advisable to keep the scraper plate as
high above the surface as possible to prevent possible
damage to the spiral auger On blacktop or concrete
surface, keep the scraper plate as close to the surface
as possible
, Raise the snow thrower off the ground and place a
block under each end of the scraper plate Loosen the
six hex nuts securing the skid shoes to the housing
Adjust the skid shoes up or down and retighten the
nuts securely. Adjust both skid shoes to the same
height to keep the housing and the scraper plate level
See figure 64
FIGURE 64
LIFT RELEASE CABLE ADJUSTMENT
• If the lift rod does not lock the snow thrower securely
in the transport position, loosen the upper hex nut on
the lift bracket a few turns and tighten the lower hex
nut. Refer to figure 48 on page 21
If the lift rod fails to unlock completely to lower the
snow thrower, loosen the lower hex nut on the lift
bracket a few turns and tighten the upper hex nut
Refer to figure 48 on page 21
CLUTCH DISENGAGEMENT ADJUSTMENT
(For tractors with engagement rod clutches only.
Not for electric clutches or cable clutches)
if the spiral auger on the snow thrower does not stop
when the attachment clutch lever on the tractor is
disengaged, then adjustment is necessary. Proceed as
foNows. Refer back to figure 33 on page 16.
• Place the attachment clutch lever in the disengaged
position.
• Remove the hairpin cotter from the engagement rod
trunnion and lift the trunnion out of the hole in the idler
arm
Screw the trunnion a few turns towards the front end
of the rod
Replace the trunnion into the hole in the idler arm and
secure it with the hairpin cotter
Check the operation of the snow thrower If the spiral
augers still do not stop, repeat the above steps until
the augers stop when the attachment dutch lever is
placed in the disengaged position
SPIRAL AUGERS
, The spiral augers are secured to the auger shaft with
two shear bolts and nylock nuts If you hit a foreign
object or if ice jams the augers, the snow thrower is
designed so that the bolts will shear
• If the augers wilt not turn, check to see if the shear
bolts have sheared See figure 65 Two replacement
shear bolts and nyiock nuts have been provided with
the snow thrower. For future use order part number
710-0890A shear bolt and number 47810 nylock nut
GEAR HOUSING
SHEAR BOLT AND SCRAPER
HEX LOCK NUT PLATE
SKID
SHOE
FIGURE 65
29