Advertisement
CUSTOMER
INSTRUCTIONS
1.
DO read thoroughly
ERATING
INSTRuCTIONS
ROUTER.
2.
DO be sure switch
connecting
tool to power supply.
DO disconnect
power cord when cleaning
3.
ing maintenance
on tool.
DO be sure the voltage
4.
agrees
with the dataplate
DO use correct
size extension
5.
mended.
DO replace
both brushes
6.
about
inch in length.
1;4
DO use only specified
7.
DO disconnect
from power source
8.
a clean dry place.
DO check bits and cutters
9.
ness.
DO keep collet clean.
10.
CAUTION
WEAR YOUR
AVOID
USE OF ALL SOLVENTS WHEN
CLEANING
PLASTIC PARTS. USE CLEAN
CLOTHS AND WIPE PARTS AS MUCH AS
POSSIBLE TO
REMOVE
DUST, ETC. MOST PLASTICS ARE SUSCEPT-
IBLE TO VARIOUS TYPES OF COMMERCIAL
SOLVENTS AND MAY BE DAMAGED BY
THE USE OF THESE SOLVENTS.'
THIS PRODUCT, or any electrical product, requires
extreme care when service repairs are made. A dan-
gerous electrical hazard can be created by tamper-
ing with the electrical
the replacement
or substitution
pairs should be made only by a qualified technician.
,f service is required we suggest you return the tool
to your nearest Sears store tor approved service with
original factory replacement
INTRODUCTION
and OP-
before
using
your
is in "OFF"
position
before
or do-
of the
power supply
marking
on the unit.
cord as recom-
when either
is worn to
replacement
parts.
and store
periodically
for tight-
DIRT,
CARBON
or insulating
systems or in
of repair parts. Re-
parts.
1.
DON'T
use
thoroughly,
INTRODUCTION
INSTRUCTIONS.
2.
DON'T
leave Router
necting
from power source.
DON'T
3.
allow the cord near cutter
erating.
DON'T
4.
allow children
DON'T
5.
carry unit by power cord.
DON'T
6,
force tool, allow Router to perform
was designed.
DON'T
plug or cover air vents to keep dust from
7.
flying.
Vents
cool.
DON'T
leave the power cord connected
in
8.
power supply when installing
DON'T
use dull knives or cutters
9.
not produce
good work and will cause
ing.
The operotion of any power tool can result in for-
eign objects being thrown into the eyes, which can
result in severe eye do mage.
glasses or eye shields before commencing
tool operation.
We recommend Wide Vision Safety
Mask for use over spectacles,
glasses . . . available
stores.
WHEN ELECTRIC TOOLS ARE USED ON FIBER-
GLASS boats, sports cars, etc. it has been found
that they are subject to accelerated
ble premature
failure, as the fiberglass chips and
grindings are highly abrasive to bearings, brushes,
commutator,
etc.
mended that this tool be used for continuous
duction work on any fiberglass
any use on fiberglass it is extremely important that
the tool is cleaned frequently
air jet.
EXTENSION CORDS-The
cord will cause some loss of power. To keep this to
a minimum and to prevent overheating
burn-out, use the table below to determine the MIN-
IMUM wire size (A.W.G.) Extension Cord.
Extension Cord Length
25- 50 Feet
50- 75 Feet
75-100
Feet
Extension cords suitable for use with your Router
are available at your nearest Sears Catalog Order
pr Retail Store.
Another time saving convenience is a cord-lock of-
fered by Sears which prevents separation
Cord-lock is available at your nearest Sears Retail
Store or Catalog Order House.
Poge 3
your
ROUTER
before
and OPERATING
unattended
before
bit when op-
to operate
Router.
must be kept open to keep motor
or changing
since they will
Always wear safety
power
or standard
safety
at Sears retail or catalog
wear and possi-
Consequently
it is not recom-
material.
by blowing with an
use of any Extension
and motor
Wire Size A.W.G.
16
14
12
of cord.
1
reading
discon-
as it
to the
cutters.
overload-
pro-
During
Advertisement
