Craftsman 315.115032 Operator's Manual page 3

WARNING: Read and understand all instruc-
tions, Failure to follow all instructionslisted
below may result in eiectdc shock,fire and/or
sedous personal injury.
SAVE THESE INSTRUCTIONS
Work Area
• Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
• Do not operate power tools in explosive etmo-
spherss, such as in the presence of flammable
liquids, gases, or dust. Power tools may create
sparks which may ignite the dust or fumes.
• Keep bystanders, children, and visitors away
while operating a power tool. Distractions can
cause you to lose control.
Electrical Safety
• Double insulated tools are equipped with a
polarized plug (one blade is wider than the
other). This plug will fit in a polarized outlet only
one way, If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit,
contact e qualified electrician to install e polar-
ized outlet. Do not change the plug in any way,
Double insulation [] eliminates the need for the
three-wire grounded power cord and grounded
power supply system.
• Avoid body contact with grounded surfaces,
such as pipes, radiators, ranges, and refrigera.
tore. There is an increased dsk of electric shock if
your body is grounded.
• Don't expose power tools to rain orwet condi-
tions, Water entedng a power tool will increase the
dsk of electric shock.
• Do not abuse the cord, Never use the cord to
carry the tools or pull the plug from an outlet,
Keep cord away from heat, oil, sharp edges, or
moving parts, Replace damaged cords immedi-
ately. Damaged cords increase the risk of electric
shock.
• When operating a power tool outside, use an
outdoor extension cord marked "W-A" or "W'.
These cords are rated for outdoor use and reduce
the risk of electric shock,
Personal Safety
• Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use tool while tired or under the influ-
ence of drugs, alcohol, or medication. A moment
of inattention while operating power tools may
result in serious personal injury,
• Dress propedy. Do not wear loose clothing or
jeweky. Contain long hair, Keep your hair,
clothing, and gloves away from moving parts.
Loose clothes, jewelry, or long hair can be caught
in moving parts.
• Avoid accidental starting. Be sure switch is off
before plugging in, CarTying tools with your finger
on the switch or plugging in tools that have the
switch on invites accidents.
• Remove adjusting keys or wrenches before
tuming the tool on, Awrench or a key that is left
attached to a rotating part of the tool may result in
personal injury.
• Do not overreach, Keep proper footing and
balance at all times, Proper footing and balance
enables better control of the tool in unexpected
situations.
• Use safety equipment. Always wear eye protec-
tion, Dust mask, non-skid safety shoes, hard hat,
or hearing protection must be used for appropriate
conditions.
Tool Use and Care
• Use clamps or other practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body is
unstable and may lead to loss of control.
• Do not force tool. Use the correct tool foryour
application. The correct tool will do the job better
and safer at the rate for which it is designed.
• Do not use tool if switch does not turn it on or
off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
• Disconnect the plug from power soume before
making any adjustments, changing accesso-
dee, or storing the tool. Such preventive safety
measures reduce the risk of starting the tool
accidentally,
• Store idle tools out of the reach of children and
other untrained persons, Tools are dangerous in
the hands of untrained users.
• Maintain tools with care. Keep cutting tools
sharp and clean. Properly maintained tools with
sharp cutting edges are less likely to bind and are
easier to control.
• Check for miselignment or binding of moving
parts, breakage of parts, and any other condi-
tion that may affect the tool's operation, If
damaged, have the tool sewiced before using.
Many accidents are caused by poody maintained
tools.
• Use only accessories that are recommended by
the manufacturer for your model. Accessories
that may he suitable for one tool, may become
hazardous when used on another tool,
3