Ryobi ESF5000 - Whole Stud Detector Manual

SAFETY RULES FOR THE DEVICE

READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

• 
  Read operator's manual carefully. Learn the applications and limitations, as well as the specific potential hazards, related to this product. Following this rule will reduce the risk of electric shock, fire, or serious injury.
• Do not operate battery products in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Battery products create sparks which may ignite the dust or fumes.
• Do not disassemble the product. Contact with internal parts may increase the risk of electric shock or cause damage to the product.
• Do not use on a ladder or unstable support. Stable footing on a solid surface enables better control of the product in unexpected situations.
• Do not store the product in an area of high heat or humidity. Do not expose the product to extended high heat from the sun (such as on a vehicle dashboard.) To reduce the risk of serious personal injury, do not store outside or in vehicles. Damage to the product or the battery can result.
• Do not expose product to rain or wet conditions. Water entering a product will increase the risk of electric shock.
• Use the product in accordance with these instructions and in the manner intended for the product, taking into account the environmental conditions and the work to be performed. Use of the product for operations different from those intended could result in a hazardous situation.
• Readings on some surfaces may be unreliable. Be aware that wallpaper containing metallic foil or fibers and plaster with metal mesh may cause the unit to function improperly.
• Ensure the device is disconnected and turned off before inserting or changing batteries.
• Do not mix old and new batteries or different brands of batteries.
• Remove batteries from the device when not in use for an extended time.
• Always replace the alkaline battery with the same type of alkaline battery. Use of any other batteries may create a risk of injury and fire.
• This device should not be operated unless the battery compartment is closed.
• Do not place battery devices or their batteries near fire or heat. This will reduce the risk of explosion and possibly injury.
• Do not crush, drop or damage battery. Do not use batteries that have been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dropped or damaged battery immediately.
• Batteries can explode in the presence of a source of ignition, such as a pilot light. To reduce the risk of serious personal injury, never use any battery device in the presence of open flame. An exploded battery can propel debris and chemicals. If exposed, flush with water immediately.
• Under extreme usage or temperature conditions, battery leakage may occur. If liquid comes in contact with your skin, wash immediately with soap and water. If liquid gets into your eyes, flush them with clean water for at least 10 minutes, then seek immediate medical attention. Following this rule will reduce the risk of serious personal injury.
• Save these instructions. Refer to them frequently and use them to instruct others who may use this device. If you loan someone this device, loan them these instructions also.

OPERATION

INSTALLING / REPLACING THE AA BATTERY

One AA battery is preinstalled in the unit. Before first use, locate and remove the red pull tab to activate the battery.

1. Battery
2. Battery compartment
3. Battery cover

• Press and slide the battery cover to open.
• Install battery according to the polarity indicators.
• Replace the battery cover, making sure it is secure before use.
• Do not use the product without the battery cover installed.
  NOTE: Remove the battery for storage when device will not be used for long periods of time.

OPERATING TIPS

Studs or joists are typically spaced 16 inches or 24 inches apart and are 1.5 inches in width. Anything closer together or of a different width may not be a stud, joist, or firebreak.

• Grip the unit only by the gripping surfaces located on the top and bottom on each side of the unit.
  NOTE: Gripping the device anywhere else on the unit may lead to faulty readings due to interference with the sensor.
• Use both hands so the unit remains firmly against the wall surface during the entire detection process.
  

USING THE DEVICE

NOTE: Readings on some surfaces may be unreliable. Be aware that wallpaper containing metallic foil or fibers and plaster with metal mesh may cause the unit to function improperly.

• Place the unit against the wall and press and hold both of the ON/OFF buttons. Hold the product still to allow the unit to calibrate. When the calibration process is completed, the LED lights will illuminate in sequence and then all flash once.
  

1. On/Off button

NOTE: Do not place the unit over a stud during the calibration p rocess.
NOTE: If the LEDs flash five times before calibration, the battery is low and needs replacing.

Locating studs or joists:

• Once calibration is complete, continue holding the ON/OFF buttons and begin to slowly move the unit in a straight line to the left or right against the wall.
• As you near a stud, the graduated display will begin to light up. The moving illuminated LEDs indicate a stud. The LED display is capable of showing the entire width of a 2x4 stud.
• When you reach the center of the stud, the two LEDs around the center mark will illuminate, indicating the unit is on center.
  

1. LED light
2. Stud center marker
3. Wall stud

• Keep the unit still. Using one hand, press the stud center marker to leave a small dimple on the wall surface. Keep other hand on the ON/OFF switch.
• To continue finding studs return hand to grip zone and activation button and begin sliding unit against surface.
  NOTE: If unit is moved before returning other hand, LEDs will flash and the unit will error. Recalibrate to resume.
• The unit will automatically turn off in 3 minutes even when the buttons remain pressed. If this occurs while detecting a large area, release the ON/ OFF buttons and repeat the steps of using the stud detector.

AC DETECTION

Do not rely on this product to penetrate a wall with any uninsulated tool. Contacting a live electrical wire may cause a serious personal injury.

A red LED will illuminate when a live electrical wire is detected behind the surface.
NOTE: Be aware of any electrical wires you encounter and avoid driving a fastener into them.

1. LED light
2. Electrical wire

MAINTENANCE

When servicing, use only identical replacement parts. Use of any other parts could create a hazard or cause product damage.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

STORAGE

Store in a cool, dry location to prevent condensation or mold from forming inside the product.
Do not store the device at temperatures greater than 122º F (such as on a dashboard or vehicle interior).

WARRANTY

This product has a Three-year Limited Warranty.
For Warranty details go to www.ryobitools.com

ONE WORLD TECHNOLOGIES, INC.
1428 Pearman Dairy Road, Anderson, SC 29625 • Phone 1-877-205-5714
États-Unis, Téléphone 1-877-205-5714 • USA, Teléfono 1-877-205-5714
www.ryobitools.com

Documents / Resources

References

• REIMAGINE WITH RYOBI - RYOBI Tools

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Ryobi ESF5000 - Whole Stud Detector Manual