Setting The Clock (Remote Control Only) - Sharp DK-KP80PH Operation Manual

General control (continued)
■ Auto power off function
The main unit will enter the stand-by mode (when iPad, iPod
or iPhone is not connected) after 15 minutes of inactivity
during:
iPod : Not docked.
Audio In : No detection of input signal.
CD : In the stop mode or no disc.
USB : In the stop mode or no media.
Note:
However, if iPod or iPhone is docked, the unit will begin
charging.
"Charge Mode" will be displayed.
■ Muting
The volume is muted temporarily when pressing the MUTE
button on the remote control. Press again to restore the
volume.
■ X-Bass control
When the power is first turned on, the unit will enter the extra
bass mode which emphasises the bass frequencies, and
"X-BASS" indicator will appear. To cancel the extra bass
mode, press the X-BASS button on the remote control.
■ Bass control
1
Press the BASS/TREBLE button to select "Bass".
2
Within 5 seconds, press the VOLUME (+ or –) button to
adjust the bass. "X-BASS" indicator will disappear.
■ Treble control
1
Press the BASS/TREBLE button to select "Treble".
2
Within 5 seconds, press the VOLUME (+ or –) button to
adjust the treble. "X-BASS" indicator will disappear.
■ Function
When the FUNCTION button on main unit is pressed, the
current function will change to different mode. Press the
FUNCTION button repeatedly to select desired function.
CD FM STEREO
Audio In
Note:
The backup function will protect the memorised function
mode for a few hours should there be a power failure or the
AC power lead becomes disconnected.
- 5 ↔ - 4 ........ ↔ + 4 ↔ + 5
- 5 ↔ - 4 ........ ↔ + 4 ↔ + 5
FM MONO
AM
USB
iPod

Setting the clock (Remote control only)

In this example, the clock is set for the 24-hour (0:00) display.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK/TIMER button.
3
Within 10 seconds, press the ENTER button. To adjust
the day, press the
ENTER button.
4
Press the or
display and then press the ENTER button.
5
To adjust the hour, press the
press the ENTER button. Press the
once to advance the time by 1 hour. Hold it down to
advance continuously.
6
To adjust the minutes, press the
then press the ENTER button. Press the
button once to advance the time by 1 minute. Hold it
down to advance the time by 5 minutes interval.
To confirm the time display:
Press the CLOCK/TIMER button. The time display will
appear for about 5 seconds.
Note:
When power supply is restored after unit is plugged in again
or after a power failure, reset the clock.
To readjust the clock:
Perform "Setting the clock" from step 1. If the "Clock" does not
appear in step 2, step 4 (for selecting the 24-hour or 12-hour
display) will be skipped.
To change the 24-hour or 12-hour display:
1
Clear all the programmed contents. [Refer to "Factory
reset, clearing all memory" on page 21 for details.]
2
Perform "Setting the clock" from step 1 onwards.
E-6
or button and then press the
button to select 24-hour or 12-hour
The 24-hour display will appear.
(0:00 - 23:59)
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
or button and then
or
or
button
button and
or