Advertisement
Function | Operation |
Power On | Take the earbuds out of the case or tap on the Touch panels of both earbuds and hold for 2 sec. |
Power Off | Put the earbuds back to the case or tap on the Touch panels of both earbuds and hold for 4 sec when no media is played. |
Pause / Play | Tap on either earbud's Touch panel once. |
Next track | Double-tap on the right earbud's Touch panel. |
Previous track | Double-tap on the left earbud's Touch panel. |
Volume + | Tap on the right earbud's Touch panel and hold until you reach the required volume level. |
Volume - | Tap on the left earbud's Touch panel and hold until you reach the required volume level. |
Answer a phone | Tap on either earbud's Touch panel during call the incoming call. |
Reject a phone | Tap on either earbud's Touch panel and hold call for 1 sec during the incoming call. |
Hang up | Tap on either earbud's Touch panel and hold for 1 sec when on a call. |
Voice assistant | Tap on either earbud's Touch panel three activation times. |
Disconnect | Tap on either earbud's Touch panel five times when the earbuds are connected to the source device. |
Factory reset | Tap on either earbud's Touch panel five times when the earbuds are not connected to the source device. |
Using the correct size ear-tips is critical for the maximum external noise isolation and a snug secure fit. It is also common to have different sized ear canals so try one ear-tip on at a time to find the best fit for each side.
To get the best possible fit with your WX8 earbuds, gently push the earbuds into your ears and adjust the headset until it fits comfortably. You should notice a drop in ambient noise when the ear-tip has been placed correctly. With a proper fit, you'll notice more range when listening to music.
To change the silicone ear-tips:
The WX8 model comes with a protective film on the charging contacts of both earbuds that is used for presale protection. Please remove the film carefully to charge the earbuds.
When the charging case runs out of power, the orange charging case indicator will start flashing. To charge the case connect it to a power source using the supplied Type-C cable or put it on a wireless charger. The orange charging case indicator will turn on and will go off when the case is fully charged. It takes up to 1.5 hours to fully charge the case either via cable or wirelessly.
Be sure to use a 5V DC, 0.5 - 1A adapter or charger. Using a power source with lower power will increase the overall charging time.
When the earbuds' battery is low, you'll hear the "Battery low" voice prompt.
To charge the earbuds, put both earbuds into the respective slots in the charging case. The earbuds will turn off automatically and start taking the charge. The earbuds' white LED indicators will turn on. It takes about 1.5 hours to charge the earbuds fully. When the earbuds are fully charged, the LED indicators will go off.
You can pair the WX8 earbuds with your device either together or separately. Using only one earbud at a time will help you to extend the overall playtime. Please read the instructions below to make the pairing process smooth and easy.
To pair both earbuds
When you turn the earbuds on, they will try to reconnect to the recently connected device. If the reconnection does not happen automatically, the earbuds will try to find the next device in the pairing list. You can only connect and play audio from one device at a time. But you can save up to 6 connected devices in the pairing list.
NOTE:
The earbud, which LED is flashing white during the painting, is the main one. For better performance, keep your smart device closer to the main earbud.
To pause and resume the playback, tap on either earbud's Touch panel once.
To change tracks on WX8, double-tap on the right earbud's Touch panel to play the next track and double-tap on the left earbud's Touch panel to play the previous track.
To adjust the volume, tap on the right earbud's Touch panel and hold to increase the volume and tap on the left earbud's Touch panel and hold to decrease the volume.
The TREBLAB WX8 can be used to make and receive calls when connected via Bluetooth. Audio playback will be paused during the calls.
To answer a call: | Tap on either earbud's Touch panel once during the incoming call. |
To reject a call: | Tap on either earbud's Touch panel and hold for 1 sec during the incoming call. |
To end a call: | Tap on either earbud's Touch panel and hold for 1 seconds when on a call. |
TREBLAB WX8 earphones are compatible with Siri, Google Voice Assistant and others. To use the voice assistant, tap on either earbud's Touch panel three times.
You can reset the WX8 earbuds to the factory default settings by cleaning up the pairing list with the last 6 connected to WX8 devices.
Make sure that the earbuds are disconnected from the source device. Tap five times on both earbuds' Touch panel. The white LEDs will light up on both earbuds and you will hear the "Power Off" voice prompt. The earbuds' memory is returned to the factory settings now.
Can't turn the earbuds ON | Please make sure the earbuds are charged, if not – charge them and try again. |
Earbuds do not charge | Please check if there is a protective tape on the charging contacts of both earbuds. If yes, please remove it and try to charge the earbuds once again. Clean the charging contacts on the earbuds with a slightly damp cotton swab when they are turned off (we recommend using water or a specially designed cleaning fluid sold for electronics). Check if the earbud slots in the charging case are free of debris. Try charging the case with another Type-C cable, power source, adaptor (if available). |
Device doesn't find TREBLAB WX8 | Make sure the WX8 buds are not paired with any other device, as they can pair only with one device at a time. If WX8 are in pairing mode and one of the earbuds flashes white, but still is not found by your device, please restart your device and the headset. Reset your earbuds to the factory settings by following the steps from the previous section. Try to pair again. |
Frequent disconnection and noise | Make sure that the distance between your device and the earbuds is less than 33 feet / 10 meters. Make sure that nothing is blocking the signal between your device and your WX8 earbuds. If the earbuds are on, but disconnected from the device for longer than 5 minutes, they will automatically turn off to save power. |
Can't connect the earbuds to the device | Make sure the WX8 earbuds are not paired with any other device, as they can pair only with one device at a time. Make sure that the distance between your device and the headphones is less than 30 feet/10 meters. Disconnect the device from your earbuds and remove WX8 from your device's pairing list. Reset your earbuds to the factory settings by following the steps from the previous section. Try to pair again. |
I cannot find a wireless driver for on my laptop | Make sure your laptop supports wireless connection. If it doesn't, you will need an external wireless USB adapter compatible with your laptop. For further details, consult with your laptop manufacturer. |
Battery: Earbud (each): 40mAh Charging case: 420mAh
Charging time: Up to 1.5 hours for the case and earbuds
Calling: 2 built-in microphones
Voice assistant activation: Supported by tapping on either earbud's Touch panel three times
Bluetooth version: BT5.0
Profiles: A2DP, AVRCP, HFP, HSP
Audio playback support: AAC, SBC
Signal Range: 33ft/10m
Driver size: 6 mm
Charging port: Type-C
Dimensions: Earbuds (each): 33.5 x 23 x 22 mm / 1.31 x 0.90 x 0.86 in
Charging case: 56.7 45 28.2 mm / 2.23 x 1.77 x 1.11 in
Weight: Earbuds (each): 4.4 g / 0.15 oz / 0.01 lb
Charging case: 35.3 g / 1.24 oz / 0.08 lb
SUITABLE: | UNSUITABLE: |
Splashes | Swimming |
Light rain or snow | Diving into water |
Sweating | Snorkeling or Scuba diving |
Showering | Watersports |
Submerge up to 3 feet / 1 meter for 30 minutes |
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download TREBLAB WX8 - Waterproof True Wireless Earbuds Manual
Advertisement
Need help?
Do you have a question about the WX8 and is the answer not in the manual?
Questions and answers