Download  Print this page

Sony PEGA-CC5 Installation/Connections page 4

Car cradle
Hide thumbs
   

Advertisement

Connecting the car
12
battery adapter
2
qd
0
1
Precautions
•Choose the installation location carefully, such
that the unit will not interfere with normal
driving operations.
•Avoid installing the unit in areas subject to dust,
dirt, excessive vibration or high temperatures,
such as in direct sunlight or near heater ducts
under the floor carpet.
•Use only the supplied mounting hardware for a
safe and secure installation.
Attaching condition (see fig.4)
This unit is attached to the dashboard of a car, and
side fin of the air vent.
The mounting attachment can be attached to an
air vent whose dimensions and shape meet
A
B
both conditions
and
.
This unit cannot be attached to a circular air
C
vent as in condition
.
Mounting support arm and
rubber blocks (see fig.5)
Combining the support arm 5 and the support
arm 6 with rubber blocks 7, attach them to the
mounting attachment 4.
Depending on the dimensions and shape of the
dashboard and the air vent, choose the support
arms so that the rubber blocks 7 are placed on the
top and bottom outer edges of the air vent.
Notes
• Choose a combination of rubber blocks 7, the
support arm 5 and the support arm 6 so that the
rubber blocks 7 do not block the air vent.
• Depending on the dimensions and shape of the dash
board and the air vent, the mounting attachment 4
can sometimes be attached without the support arm
5 or the support arm 6.
Installing the mounting
attachment (see fig.6)
A
Mounting the mounting attachment.
Choose either the holding clip (S) 8 or the
holding clip (L) 9, depending on the width of
the side fin of the air vent.
1
1 Insert the holding clip into the air
vent and hook the holding clip on
the side fin.
2 Adjust the attachment position so that
the holding clip does not touch the
back fin. If you insert the holding clip
forcibly, the back fin may be damaged.
Note
Setting the holding clip and the side fin parallel,
attach the mounting attachment.
2
With the holding clip hooked on the side fin
of the air vent, feed the holding clip into the
hole on the back of the mounting attachment,
and pull the holding clip until the mounting
attachment becomes stable.
Tip (6-
)
*
If the rubber blocks 7 of the car cradle slip and the car
cradle cannot be attached to the dashboard securely,
attach it using the two-sided tape qf between the
rubber blocks 7 and the dashboard. The two-sided
tape qf can be cut. Cut it to a size larger than the
rubber block 7 itself. The two-sided tape qf is
ineffective if it is cut too small.
Please consult qualified technician or service personnel
if you cannot attach the car cradle to the car securely.
Notes
• If you pull the holding clip too firmly, the fin of the
air vent may be damaged.
• If the air vent fin is set to swing automatically, stop it
before mounting the mounting attachment.
• By doing the following, make sure that the
mounting attachment and the holding clip are
attached securely and do not vibrate.
– Pull the mounting attachment lightly and push
it up and down.
– Push and pull the mounting attachment against
the air vent.
You can also fix the cord of the GPS
antenna or the car battery adapter to
the hooks on both sides of the
mounting attachment.
cord
hook
B
Removing the mounting attachment
1
1 Press the lever on the bottom of the
mounting attachment.
2 loosen the holding clip by pulling the
mounting attachment forward.
2
1 Press the mounting attachment to the air
vent.
2 Twist the mounting attachment slightly.
3 Pull the mounting attachment off towards
you.
Attaching the holding arms
(see fig.7)
Depending on the type of the CLIÉ handheld(short
screen or long screen), choose either the holding
arm 2 or the holding arm 3.
Short screen type
"Size S" is marked on the back of
SIZE S
the holding arm 2.
>ABS<
Long screen type
"Size L" is marked on the back of
SIZE L
>ABS<
the holding arm 3.
1
Remove the sheet attached to the car cradle.
When removing the sheet, be careful not to let
any objects get into the slots of the car cradle.
2
Attach the holding arms chosen according to
the type of CLIÉ handheld.
1 Insert the holding arms' tab
into the car
cradle.
2 Pull both sides of the holding arms outwards
and insert the tab
.
Detaching the holding arms
When replacing the holding arms 2 with the
holding arms 3 to use the different type of CLIÉ
handheld, etc., insert the tip of a slotted
screwdriver into the slot for the tab
and release
the lock of the tab. There are two tabs: one on the
left and one on the right.
Mounting the car cradle to the
mounting attachment (see fig.8)
1 Slide the tip of the mounting attachment
along the slit on the back of the car cradle to
mount it.
2 Rotate the dial
to fix the car cradle.
Attaching your CLIÉ handheld
(see fig.9)
Mounting
1 Mount your CLIÉ handheld on the connector of
the car cradle.
2 Tilt back your CLIÉ handheld rest in the car
cradle.
Note
Do not mount your CLIÉ handheld while driving.
Adjusting the angle (see fig.0)
Adjust the angle of the car cradle by dial
mounting attachment.
Attaching a GPS antenna (see fig.qa)
Dashboard
Roof B
Roof A
13
Detaching your CLIÉ handheld
1
A
Attaching to the inside of a car
•Install the GPS antenna on the dashboard.
•Install the GPS antenna on a flat surface to keep it
horizontal.
•Choose the attachment position where the best
reception is achieved. Also, choose the position
where no obstacle blocks the reception from the
GPS satellite.
Note
Some types of front windshield do not let the radio
wave from a GPS satellite pass.
If the reception of the radio wave is poor when the GPS
antenna is attached to the inside, attach it to the
outside of the car roof.
Before attachment
• Make sure that the GPS antenna has good
reception and not hidden behind car ornaments,
the windscreen wiper, etc.
• Make sure that the GPS antenna does not disturb
operation of car equipment.
• Clean the mounting surface.
1
Remove the release-coated paper from the
surface of the base sheet qs, and then place
the GPS antenna qa on the center of the base
sheet qs.
qa
qs
2
Remove the release-coated paper from the
back surface of the base sheet qs, and stick
the base sheet qs to the mounting surface.
To mounting surface
Notes
• Fix the cord to the position that does not obstruct the
operation of passenger-side airbag.
• Fix the cord of the GPS antenna using the cord clamps
qd if necessary, to prevent the cord from disturbing
driving. If the cord tangles up the gearshift, etc., it is
extremely dangerous.
• Attach the cord clamps qd after cleaning the
mounting surface.
B
Attaching to the outside of a car
•Attach the GPS antenna horizontally in a place
where GPS satellite reception is not blocked by
the car roof.
•The GPS antenna is attached by a magnet.
When attaching it on the car, place it carefully, so
as not to harm the car's body surface.
When attaching to a car of aluminum or FRP
body
Since the magnet will not stick to aluminum or
FRP, attach the GPS antenna to the inside of the
car.
of the
Before attachment
Clean the mounting surface.
1
Attach the GPS antenna to the roof.
Clean the
mounting
surface before attaching.
qa
2
1
2
Place cord.
Roof A
Pass the GPS antenna cord over the roof,
passing the windshield pillar, fender and
molding, and then pull it inside of the car.
Note
Secure the cord with the cord clamps in the form of
a U-shape to prevent rain water from entering the
car along the cord.
Roof B
Pass the GPS antenna cord over the roof,
passing the center pillar,windshield pillar inner
side and dashboard, and then pull it into the
car.
Notes
• Do not place the cord on the inside of the car if
the car uses a curtain-type side airbag that spreads
from the windshield pillar over the center pillar,
or a shock-absorbing structure for its interior.
• Secure the cord using the cord clamps to make the
cord form U-shape so that rain water does not
enter into the car along the cord.
Notes on GPS antenna
• Do not allow the cord to slack outside of the car.
• Depending on the car, the antenna cord may not be
long enough to reach the roof. In this case, attach the
GPS antenna to the inside of the car.
• Secure the cord of the GPS antenna with the cord
Place the GPS
clamps qd if necessary, to prevent the cord from
antenna on the
disturbing driving.
center of the base
• When detaching the GPS antenna, do not pull the
sheet.
cord. since the magnetic power is strong, the cord
may detach.
• When washing your car by an automatic car-washing
machine, detach the GPS antenna. Otherwise, the
antenna may be detached during washing, and
damage your car.
• GPS signals and DC power are flowing through the
GPS antenna cord. When attaching the GPS antenna,
be careful that the cord is not caught in any moving
parts of the car. A damaged cord results in
malfunction of the GPS antenna and the car cradle.
• Do not place the cord on the inside of the car if the
car uses a curtain-type side airbag that spreads from
the windshield pillar over the center pillar, or a shock-
absorbing structure for its interior.
For details, please consult qualified technician or
service personnel.
On painting of the GPS antenna
The GPS antenna can be painted to match the car's
body color. However, do not use metallic paint, as
it may cause poor reception or reception error.
Also, when painting, do not dismantle the antenna.
Connecting the car battery
adapter (see fig.qs)
Connect the car battery adapter 0 to the DC 5.2V
connector of car cradle ( 1 ), and connect the car
battery adapter into the cigarette lighter socket
( 2 ).
Notes
• Do not plug the car battery adapter into the cigarette
lighter socket immediately after using the cigarette
lighter. First allow the socket to cool down.
• To fix the cord of the car battery adapter, use the
cord clamps qd if necessary.
Clean the mounting surface before attaching the cord
clamps.
Detaching your CLIÉ handheld
(see fig.qd)
Detaching
1 Squeeze both RELEASE buttons simultaneously
with one hand.
2 Pull out the CLIÉ handheld towards you from
the top with your other hand.
Notes
• Do not detach your CLIÉ handheld from the car cradle
with one hand, it may cause a malfunction.
• Do not detach your CLIÉ handheld while driving.

Advertisement

Table of Contents
loading

  Related Manuals for Sony PEGA-CC5