Before Use - Electrolux McCulloch Power Trim ET700 Manual

Hide thumbs Also See for McCulloch Power Trim ET700:
Table of Contents

Advertisement

13. Remove the plug from the mains :
-
before leaving the trimmer unattended for any
period;
-
before clearing a blockage;
-
before checking, cleaning or working on the
appliance;
-
if you hit an object. Do not use your trimmer until
you are sure that the entire trimmer is in a safe
operating condition;
-
if the trimmer starts to vibrate abnormally. Check
immediately. Excessive vibration can cause injury.
Assembly of Switch Handle to Tube (A1)
Ensure that the internal cable is not twisted.
1. Insert the tube into the switch handle.
2. Push until it clicks into position.
ENSURE THAT THE TUBE IS FULLY LOCATED
BY ATTEMPTING TO REMOVE IT.
Assembly of Trimmer Head to Tube (A2)
Ensure that the internal cable is not twisted.
1. Insert the tube into the trimmer head.
2. Push until it clicks into position.
ENSURE THAT THE TUBE IS FULLY LOCATED
BY ATTEMPTING TO REMOVE IT.
Safety Guard Assembly (B1) & (B2)
1. Locate the safety guard over the cutting head.
Ensure the nylon line is fed through the hole in the
safety guard as illustrated in fig B1.
2. Push into location and turn safety guard in the
direction illustrated in Fig B2, until a click is heard
and the safety guard is securely locked in position.
ENSURE THE SAFETY GUARD IS SECURELY IN
PLACE BY ATTEMPTING TO TWIST GUARD.
F1 - Line cutter
How the automatic line feed works (F)
1. When initially switching on the trimmer, a small
length of line is fed out.
2. A 'clattering' noise will be heard when the two nylon
lines hit the line cutter. DO NOT BE ALARMED
this is quite normal. After approximately 5 seconds
the line will be cut to the correct length and the
noise will reduce as the motor reaches full speed.
Make sure the motor is up to full speed before
trimming or edging.
WARNING
The use of eye protection is recommended. Do not
lean over the trimmer whilst trimming or edging,
objects may be thrown by the cutting line. Do not
allow cutting head to rest on the ground. Do not
overload your trimmer. Overloading can be avoided
by making sure the motor speed does not drop
unduly. DISCONNECT FROM THE MAINS
ELECTRICITY SUPPLY BEFORE ATTEMPTING ANY
MAINTENANCE OR ADJUSTMENT.

BEFORE USE:

Make sure that both lines are fed out.
Make sure motor is up to full speed before trimming
or edging.
How to trim
1. Hold as illustrated in Fig G.
2. To start, squeeze the switch lever.
3. Cut with nylon line at an angle using the tip. See Fig
H.
4. Swing trimmer in and out of the cutting area taking
small cuts (J).
Safety Precautions
Assembly Instructions
Double Auto Feed System
How to Trim and Edge
Get other manuals https://www.bkmanuals.com
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure the
trimmer is in safe working condition.
2. Replace worn or damaged parts for safety.
3. Only use the replacement cutting line specified for
this product.
4. Only use replacement parts and accessories
recommended by Electrolux Outdoor Products.
5. To avoid the risk of injury keep fingers and hands clear of
the line cutter on the leading edge of the guard.
6. Inspect and maintain the trimmer regularly. Any repairs
must be carried out by an authorised repairer.
Steady Handle Assembly (C)
1. Depress the two buttons on the sides of the switch
handle.
2. Locate the steady handle over the buttons and
release the buttons.
3. Adjust the steady handle to the most comfortable
operating position by depressing the buttons and
moving the handle.
Height Adjustment (D)
1. Turn height adjuster (D1) in the direction indicated to
un-lock (D2).
2. Adjust the length of the tube to the most comfortable
operating position.
3. Turn height adjuster in the opposite direction to lock
(D3).
ENSURE THAT THE TUBE IS FULLY SECURED.
Cable Restraint (E1) & (E2)
1. Form loop in mains cable and push the loop through
the slot as illustrated in picture (E1).
2. To secure, position loop over the hook and pull the
cable back through the slot as illustrated in picture (E2).
3. If the noise of the nylon line being cut cannot be
heard, more line will need to be fed out.
4. To feed more line, it is first necessary to to allow the
motor to stop completely, then re-start, allowing the
motor to reach full speed.
5. Repeat step 4. until you hear the lines hitting against
the cutter. (Do not repeat this procedure more than
6 times)
6. If problems are experienced with the automatic line
feed refer to Fault Finding Chart.
5. Line is fed out automatically every time the trimmer
head stops rotating and returns to operating speed.
6. To stop your trimmer release the switch lever.
How to edge
1. To convert to edging mode, depress the locking
button (K1) and twist head anti-clockwise (K2). An
audible "click" will confirm that the head is locked.
Ensure the button has returned to its original
position.
2. Hold as illustrated in Fig G.
3. To start, squeeze the switch lever.
4. Rest the edger on the roller for extra stability and
line up the edge of the lawn with the two indicators
on the guard (L1). Edge in direction indicated in Fig
L.
5. To stop your trimmer release the switch lever.
6. To return to trimming mode, depress the locking
button and twist head clockwise. An audible "click"
will confirm that the head is locked. Ensure the
button has returned to its original position.
ENGLISH - 2

Advertisement

Table of Contents
loading

This manual is also suitable for:

Mcculloch power trim et500

Table of Contents