Sony MEX-5DI Installation/Connections

MG-MS/FM/AM
Compact Disc
Player
Installation/Connections
Installation/Connexions
Instalación/Conexiones
MEX-5DI
Sony Corporation © 2002
1
7
121 (4 / )
8
19 ( 3
3
9.5 ( / )
8
59 (2 3 / )
8
Unit: mm (in.)
Unité : mm (po.)
Unidad: mm
Dimensions include unit size, front panel and disc tray open, etc.
Les dimensions comprennent l'appareil lui-même, la façade et le plateau de disque lorsqu'ils sont
ouverts, etc.
Las dimensiones incluyen el tamaño de la unidad, el panel frontal y la bandeja de discos abierta, etc.
2
1
4 5
Equipment used in illustrations (not supplied)
Appareils utilisés dans les illustrations (non fournis)
Equipos utilizados en las ilustraciones (no suministrados)
Front speaker
Haut-parleur avant
Altavoz delantero
Rear speaker
Haut-parleur arrière
Altavoz trasero
Active subwoofer
Caisson de graves actif
Altavoz potenciador de graves activo
3-242-050-11 (1)
Printed in Japan
5
142.5 (5 / )
8
/ )
4
170 (6 3 / )
4
2 3
4
6 7
Power amplifier
Amplificateur de puissance
Amplificador de potencia
CD/MD changer
Changeur de CD/MD
Cambiador de CD/MD
3 A
B
Cautions
• This unit is designed for negative ground 12 V DC
operation only.
• Do not get the wires under a screw, or caught in
moving parts (e.g. seat railing).
• Before making connections, turn the car ignition
off to avoid short circuits.
• Connect the yellow and red power input leads
only after all other leads have been connected.
• Run all ground wires to a common ground
point.
• Be sure to insulate any loose unconnected wires
with electrical tape for safety.
• The use of optical instruments with this product
will increase eye hazard.
Notes on the power supply cord (yellow)
• When connecting this unit in combination with
other stereo components, the connected car
circuit's rating must be higher than the sum of
each component's fuse.
• When no car circuits are rated high enough,
connect the unit directly to the battery.
Before installation (1)
Do not install the unit where its operation interferes
with driving.
2
Example:
— Opening and closing of the front panel or disc
tray interfere with operation of the gear shift.
— With the front panel open, operation of hazard
lamps, switches etc., is impaired.
Parts Iist (2)
The numbers in the list are keyed to those in the
instructions.
For the use of release key 7, see the supplied
operating instructions.
Caution
Handle the bracket
1 carefully to avoid
injuring your fingers.
AUDIO OUT
SUB OUT (MONO)
FRONT
AUDIO OUT
REAR
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
Source selector*
Sélecteur de source*
Selector de fuente*
XA-C30
BUS CONTROL IN
Connection example (3)
Note (3-A)
Be sure to connect the ground cord before connecting
the amplifier.
Tip (3-B- )
For connecting two or more CD/MD changers, the source
selector XA-C30 (optional) is necessary.
Connection diagram (4)
1
To a metal surface of the car
First connect the black ground lead, then connect
the yellow and red power input leads.
2
To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
• It is not necessary to connect this lead if there is no
power antenna or antenna booster, or with a
manually-operated telescopic antenna.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see "Notes on the control and
power supply leads."
3
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4
To the interface cable of a car telephone
5
To a car's illumination signal
Be sure to connect the black ground lead to it first.
6
To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the +12
V power (battery) terminal which is energised at all
times.
Be sure to connect the black ground lead to it first.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see "Notes on the control and
power supply leads."
7
To the +12 V power terminal which is energised
at all times
Be sure to connect the black ground lead to it first.
Notes on the control and power supply leads
• The power antenna control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/AM antenna in the rear/
side glass, connect the power antenna control lead
(blue) or the accessory power input lead (red) to the
power terminal of the existing antenna booster. For
details, consult your dealer.
• A power antenna without relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected, power
will always be supplied to the memory circuit even when
the ignition key is turned off.
* not supplied
non fourni
no suministrados