Download Print this page

Cornelius CCM330 Installation Instructions

30" nordic black/gray style lid kits

Advertisement

Quick Links

INSTALLATION INSTRUCTIONS

ED2XX 30" CCM330/430/530/630/830/1030 N
S
L
K
TYLE
ID
ITS
This Nordic style kit applies to the Cornelius 30" wide CCM322/522 ice maker.
Item No.
Part No.
53003
1
52969
15537
2
29565
3
4
70217
5
50904
6
90221
7
620204731INS
8
620701902
9
620701901
10
620037003
11
621701903
620505802
12
13
630500109
!
WARNING:
Disconnect power to the unit before installing the adaptor following all lockout/tag out procedures established by the
user. Verify that all the power is off to the unit before performing any work.
Failure to comply could result in serious injury, death or damage to the equipment.
!
WARNING:
All ice baffle plates and bin stats, if included or recommended in this kit, must be installed as directed in this manual or
the equipment manufacturer's instructions.
Failure to comply could result in serious injury, death or damage to the equipment.
!
WARNING:
All of the attachment screws and plates must be installed as directed in this manual.
Failure to comply could result in serious injury, death or damage to the equipment.
1. Unpack the kit.
2. Place the insulation strip (item 12) over the studs on the baffle and insert the baffle assembly into the adapter lid.
3. Place (2) sealing washers (item 9) over the studs and (2) flat washers (item 11), then fasten in place with (2) plas-
tic acorn nuts (item 8).
4. Set the ice maker lid on the top of the dispenser.
5. Using the slotted holes in the lid as a template, drill four (4) 0.140" diameter (9/64") holes at the bottom of the slots
(see detail A). Use extreme care not to drill into the hopper. Fasten the lid to the dispenser with four (4) #8 sheet
metal screws, two on each side.
6. Seal the icemaker to the top of the dispenser as follows:
A. Run beads of RTV around the opening in the lid and inside of the perimeter of the ice maker outline so
that the ice maker sets on the RTV.
Release Date: October 30, 2010
© 2007-2010, IMI Cornelius Inc.
ED2XX 30" CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions
Cover, Gray
Cover, Black
Lid Assembly
Bracket
#8 Screw
RTV
Label
Installation Instructions
Acorn Nut, 8--32 Nylon
Sealing Washer
Baffle, Ice
#8 Nylon Washer
Insulation Strip
Bin Stat
www.cornelius.com
ORDIC
Name
- 1 -
B
/G
LACK
RAY
Qty.
1
1
2
6
1
1
1
2
2
1
2
1
1
Revision: B
Publication Number: 620204731INS

Advertisement

loading

Summary of Contents for Cornelius CCM330

  • Page 1: Installation Instructions

    6. Seal the icemaker to the top of the dispenser as follows: A. Run beads of RTV around the opening in the lid and inside of the perimeter of the ice maker outline so that the ice maker sets on the RTV.
  • Page 2 8. Install the wire form bracket, supplied with the bin stat kit (item 4), through the 5/8” diameter hole in the bottom of the ice maker. Wrap the eye of the wire form over the stud near the hole to the end of the wire form bracket and wrap the tube around the end of the bracket several times, insuring the tube is secure.
  • Page 3 ED2XX 30” CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions Figure 2. ED2XX Kit © 2007-2010, IMI Cornelius Inc. - 3 - Publication Number: 620204731INS...
  • Page 4 ED2XX 30” CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions FRONT PANEL OF ICE MAKER REMOVED FOR CLARITY SEE DETAIL X IN FIGURE 3 BINSTAT COIL DETAIL X SCALE 0.580 NOTE: BINSTAT MUST BE WRAPPED AROUND SUPPORT AS SHOWN. Publication Number: 620204731INS Figure 3.

This manual is also suitable for:

Ccm530Ccm430Ccm630Ccm830Ed2xx