Download Print this page

Cornelius 430 Installation Instructions

30” nordic black/gray style lid kits

Advertisement

Quick Links

ED/DF300 30" CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions

INSTALLATION INSTRUCTIONS

ED/DF300 30" CCM330/430/530/630/830/1030 N
S
L
K
TYLE
ID
ITS
This Nordic style kit applies to the Cornelius 30" wide CCM330/430/530/630/830/1030 ice maker.
Item No.
Part No.
1
15209
22127
2
50904
3
52946
4
52964
91957
5
620042919
6
70226
7
620701902
8
620701901
9
611701903
10
15192
11
12
630500109
!
WARNING:
Disconnect power to the unit before installing the adaptor following all lockout/tag out procedures established by the
user. Verify that all the power is off to the unit before performing any work.
Failure to comply could result in serious injury, death or damage to the equipment.
!
WARNING:
All ice baffle plates and bin stats, if included or recommended in this kit, must be installed as directed in this manual or
the equipment manufacturer's instructions.
Failure to comply could result in serious injury, death or damage to the equipment.
!
WARNING:
All of the attachment screws and plates must be installed as directed in this manual.
Failure to comply could result in serious injury, death or damage to the equipment.
!
WARNING:
The dispenser must be secured with 3/8-16 bolts (6) to the counter before installing this Ice Maker Adapter Kit. Refer
to the installation manual and Figure 3 for the counter mounting template.
NOTE: Adjust the automatic agitation timer located in the dispenser's electrical control box to 5 sec-
onds on, 20 minutes off. Access to the timer is provided by removing the merchandiser/upper
front panel.
1. Unpack the kit.
2. Remove the two (2) screws from each side of the dispenser cabinet and the plastic hopper covers (2) that were
shipped with the unit.
3. Place the adapter lid on the unit and use the four (4) screws that were removed to fasten the lid in place.
4. Install the ice baffle on the lid assembly as shown in Figure 2.
Release Date: November 4, 2010
© 2007-2010, IMI Cornelius Inc.
Table 1. Supplied Loose Parts
Adapter Lid
Bracket
RTV
Cover, Gray
Cover, Black
Label
Baffle, Ice
#10 x 3/4" Sheetmetal Screw
Acorn Nut, 8--32 Nylon
Sealing Washer
#8 Nylon Washer
Lid Opening Cover (For 22–inch Wide Icemakers)
Bin Stat
www.cornelius.com
- 1 -
B
ORDIC
LACK
Name
Publication Number: 620204732INS
/G
RAY
Qty.
1
2
1
1
1
1
12
4
4
4
2
1
Revision: B

Advertisement

loading

Summary of Contents for Cornelius 430

  • Page 1: Installation Instructions

    Failure to comply could result in serious injury, death or damage to the equipment. WARNING: The dispenser must be secured with 3/8-16 bolts (6) to the counter before installing this Ice Maker Adapter Kit. Refer to the installation manual and Figure 3 for the counter mounting template.
  • Page 2 7. Install the wire form bracket, supplied with the bin stat kit (item 4), through the 5/8” diameter hole in the bottom of the ice maker. Wrap the eye of the wire form over the stud near the hole to the end of the wire form bracket and wrap the tube around the end of the bracket several times, insuring the tube is secure.
  • Page 3 ED/DF300 30” CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions Figure 2. ED/DF300 Kit Ice Baffle Installation Figure 3 ED/DF300 Mounting Template © 2007-2010, IMI Cornelius Inc. - 3 - Publication Number: 620204732INS...
  • Page 4 ED/DF300 30” CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions FRONT PANEL OF ICE MAKER REMOVED FOR CLARITY SEE DETAIL X IN FIGURE 3 BINSTAT COIL DETAIL X SCALE 0.580 NOTE: BINSTAT MUST BE WRAPPED AROUND SUPPORT AS SHOWN. Publication Number: 620204732INS Figure 4.

This manual is also suitable for:

530630830Ed/df300Ccm330Ccm430 ... Show all