Advertisement
Quick Links
Advertisement
Related Manuals for ALKOVA SUR 80
Summary of Contents for ALKOVA SUR 80
- Page 1 80 / 102 Instruction Manual Version: 2019 V1...
-
Page 3: Table Of Contents
Content Item Page No. 1. Safety Precaution 2. Parts & Accessories 3. Installation Instruction 4. Transmitter Function & Assembly 5. Power Supply Connection & Circuit Diagram 6. Maintenance 7. Technical Specifications 8. Customer Service Centre... -
Page 4: Safety Precaution
Safety Precaution WARNING Installation and maintenance work shall only be performed by qualified persons, familiar with local code and regulation, and experienced with this type of appliance. All field wiring must be installed in accordance with the national wiring regulation. Ensure that the rated voltage of the unit corresponds to that of the name plate before commencing wiring work according to the wiring diagram. - Page 5 Safety Precaution WARNING This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
- Page 6 Safety Precaution CAUTION Please take note of the following important points when installing. The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a sufficient strength to withstand 4 times the weight of the ceiling fan. The mounting of the suspension system shall be performed by the manufacturer, its service agent or suitably qualified persons.
- Page 7 Safety Precaution CAUTION Before turning off the power supply set the remote controller’s ON/OFF switch to the “OFF” position. If this is not done, the unit’s fans will start turning automatically when power resumes, posing a hazard to service personnel or the user. Do not operate any heating apparatus too close to the ceiling fan unit or use in room where mineral oil, oil vapour or oil steam exist, this may cause plastic part to melt or deform as a result of excessive heat or chemical reaction.
-
Page 8: Parts & Accessories
Parts & Accessories Pan Bolt, Flat Washer, Lock Washer, Nut and Clevis Pin x 2 Canopy x 1 Canopy Cover x 1 Motor Assembly x 1 Expansion Expansion Wood Screw and Flat Bolt with Bolt with Coupling Cover x 1 Nut x 3 Hook x 1 Washer x 4... - Page 9 Parts & Accessories Blade x 6 Wall Screw x 2 Blade Screw, Rubber Washer Flat Washer, and Nut x 19 Battery x 2 Wire Connector x 3 Transmitter & Holder x 1...
-
Page 10: Installation Instruction
Installation Instruction Loosen Suspension Screw Sets Safety Cable at top of Motor Assembly. Wires Route Safety Cable and Wires through Downrod. Fix the Downrod Coupling Screw x 2 Downrod to the Coupling with Bolt, Washer, Nut and tighten Bolt x 2 them firmly then insert Clevis Pin. - Page 11 Installation Instruction Assemble the Coupling Cover, Canopy Cover, and the Canopy Canopy through Downrod. Canopy Cover Coupling Cover...
- Page 12 Installation Instruction Concrete Ceiling Install the Mounting Bracket onto concrete ceiling with the Expansion Bolt with Nut and Expansion Bolt with Hook. Important: Screw and Nut must be tightened Safety Wire till snug. Safety Wire must install according to instruction.
- Page 13 Installation Instruction Wooden Ceiling Install the Mounting Bracket onto wooden ceiling with the Wood Screw and Flat Washer. Important: Screw must be tightened till Safety Wire snug. Safety Wire must install according to instruction.
- Page 14 Installation Instruction Install the Pan Bolt, Flat Washer, Lock Washer, Nut and Clevis Pin into the bottom hole on top of the Downrod.
- Page 15 Installation Instruction Mounting Bracket Raise the fan, align the Bolt on Downrod and slide through the groove on Mounting Bracket until it sits firmly into the slot. Note: The Downrod could not be rotated if this step is Slot done correctly. Downrod...
- Page 16 Installation Instruction Insert the Bolt into the upper hole on Downrod and secure with Flat Washer, Lock Washer and Nut. Tighten the 2 bolts. Important: Bolts must be tighten till snug.
- Page 17 Installation Instruction House Supply Wires Blue (N) Wire Green/Yellow (E) Brown (L) Wire Connect the wires from fan to house’s supply wires.
- Page 18 Installation Instruction Mounting Bracket Loosen the 2 Canopy Screws on Mounting Bracket. Place Canopy on the Mounting Bracket. Align the keyholes on Canopy Canopy with Mounting Bracket and secure with the 2 screws. Canopy Screws Canopy Cover Place the Canopy Cover on Canopy.
- Page 19 Installation Instruction Warning: DO NOT use power tools to assemble the blades. Over-tightening the screws causes stress on blades which may result in crack and breakage. Place the Blade on top of Blade Holder. Install Blade with the Screws provided. Flat Washer Rubber Washer Important: Blade Screws...
- Page 20 Installation Instruction Below shows a complete installation diagram...
- Page 21 Transmitter Learning Process The receiver & transmitter is pre-programmed in factory. If you wish to control 2 or more fans using 1 transmitter, the below steps are required. DO NOT PRESS ANY OTHER BUTTON DURING THIS PROCESS Transmitter Turn on power to fan. Within 30 sec, press and hold “LEARN”...
-
Page 22: Transmitter Function & Assembly
Transmitter Function Power Turn off fan Fan Speed 1 - Lowest speed 8 - Highest speed Natural Wind Fan speed changes within Forward Reverse its range creating gentle Anti-clockwise or sea-breeze effect clockwise rotation Timer On 1h - Fan turns on after 1 hour 3h - Fan turns on after 3 hours 6h - Fan turns on after 6 hours 8h - Fan turns on after 8 hours... - Page 23 Function of Forward & Reverse Fan must be turned on and rotating. Press and hold button for 3 sec. Fan will slow down and then change direction (approx. 15 sec). When the fan is slowing down to change direction, the Fan Speed function is disabled until direction has been changed.
- Page 24 Transmitter Assembly Install the Transmitter Holder to wall with the 2 Screws provided. Transmitter Holder...
-
Page 25: Power Supply Connection & Circuit Diagram
Power Supply Connection IMPORTANT : DO NOT CONNECT THIS REMOTE CONTROL CEILING FAN TO REGULATOR OR DIMMER SWITCH. Regulator Dimmer Switch Breaker Switch 220 - 240V~ 50Hz Power Supply Earth Wall Switch On/Off... - Page 26 Circuit Diagram Motor ANT1 MAIN PCB Blue Neutral (Blue) Brown Live (Brown) Power Supply 220 - 240V~ 50Hz Green/Yellow Earth (Green/Yellow) 220 - 240V~ 50Hz...
-
Page 27: Maintenance
Maintenance Due to the fan’s natural movement, connections may get loose after a period of usage. To ensure a proper and safety usage, it is highly recommended to inspect and tighten all connections every 6 months. Cleaning Cleaning your fan periodically will prolong its new appearance. Basic cleaning procedures are as follows : 1. -
Page 28: Technical Specifications
Technical Specifications MODEL SUR / 80 SUR / 102 No. of Blades 80” 102” Fan Width Motor RPM 20 - 161 20 - 107 Voltage 220 - 240V~ 50Hz Motor Wattage 4W - 95W 4W - 95W Nett Weight 17.0 Kg 17.9 Kg Information may subject to 5% variation. - Page 29 Technical Specifications 368mm 508mm (1’ 8”) (1’ 8”) More than 1m SUR/80 - 2032mm (6’ 8”) SUR/102 - 2590mm (8’ 6”)
-
Page 30: Customer Service Centre
Customer Service If you need any technical assistance or faulty report, please contact our customer service centre at : ALPHA HOME APPLIANCES SDN. BHD. (390258-H) Head Office Melaka 6, Jalan Sungai Kayu Ara 32/37, Berjaya Park, 19, 19-1 & 19-2, Jalan KSB 11, Section 32, 40460 Shah Alam, Selangor.
Need help?
Do you have a question about the SUR 80 and is the answer not in the manual?
Questions and answers