1. INTRODUCTION INTRODUCTION This manual explains how to control an LV 5800(A) remotely over an Ethernet. For other explanations and notes, see the main LV 5800(A) instruction manual. About Network The remote control capability operation via the Ethernet is confirmed only under the local network environments;...
2. ETHERNET ETHERNET You can set nearly all settings that can be specified using the front panel keys by transferring the command to LV 5800(A) using the PC that is connected via Ethernet network. In addition, the various data that is detected by LV 5800(A) can be transferred to the PC that is connected via Ethernet network.
2. ETHERNET FTP File Transfer To transfer files from LV 5800(A) to PC connected to the network, FTP is used. For a description on how to start (*1) FTP, see the instruction manual that came with your PC. The user name and password cannot be changed on the LV 5800(A). When the FTP starts, “User”...
2. ETHERNET Command Entry Procedure The system of control commands used on the Ethernet network follows the menu structure. Reading this manual and the instruction manuals of each Unit of the LV 5800(A) will facilitate the process. ● Entry Method of the Command The entry method of the command is shown below.
2. ETHERNET TELNET Commands 2.4.1 LV 5800(A) Commands (MULTI MONITOR) ● Front Panel LV 5800(A) (MULTI MONITOR) Command Parameter1 Description DISPLAY Selects first area Selects second area Selects third area Selects fourth area Queries the selected area MULTI Selects multi screen display Selects 1 screen display Queries the multi screen display INPUT:UNIT...
Page 8
2. ETHERNET ● PLATFORM SETUP (GENERAL SETUP) LV 5800(A) (MULTI MONITOR) Command Parameter1 Description SYS:PLATFORM:SOURCE_MODE SINGLE Sets the single input mode. MULTI Sets the multi input mode. (Doesn’t interlock with the line selection.) MULTI_LINE Sets the multi input mode. (Interlocks with the line selection.) Queries the input mode.
Page 9
2. ETHERNET ● PLATFORM SETUP (REMOTE) LV 5800(A) (MULTI MONITOR) Command Parameter1 Description SYS:PLATFORM:REMOTE_MODE Recalls the presets from No.1 to 8 by bit. BINARY Recalls the presets from No.1 to 60 by binary code. Queries the remote mode. SYS:PLATFORM:ALARM:POLARITY POSITIVE High is output at the time of error detection NEGATIVE Low is output at the time of error detection...
Page 10
2. ETHERNET ● DATE&TIME LV 5800(A) (MULTI MONITOR) Command Parameter1 Description SYS:DATE YYYY/MM/DD,hh:mm:ss Sets up the date and time. Queries the date and time ● SYSTEM INFORMATION LV 5800(A) (MULTI MONITOR) Command Parameter1 Description SYS:UNIT1_INFO Queries the unit 1 type SYS:UNIT2_INFO Queries the unit 2 type SYS:UNIT3_INFO...
2. ETHERNET 2.4.2 LV 58SER01A Commands (SDI INPUT) ● UNIT SETUP (GENERAL SETUP) LV 58SER01A (SDI INPUT) Command Parameter1 Parameter2 Description SYS:UNIT:LINK_FORMAT 1,2,3,4 (*1) SINGLE Sets the link format to single link. DUAL Sets the link format to dual link. Sets the link format to 2048 ×...
Page 12
2. ETHERNET Command Parameter1 Parameter2 Description SYS:UNIT:MANUAL_FORMAT 1,2,3,4 720P/24 Sets the format to 720p/24 at the time of single link. 720P/23.98 Sets the format to 720p/23.98 at the time of single link. 525I/59.94 Sets the format to 525i/59.94 at the time of single link.
Page 13
2. ETHERNET ● UNIT SETUP (ERROR SETUP1) LV 58SER01A (SDI INPUT) Command Parameter1 Parameter2 Description SYS:UNIT:ERROR:TRS 1,2,3,4 Detects the TRS errors. Does not detect the TRS errors. Queries the presence of TRS error detection. SYS:UNIT:ERROR:HD_LINE 1,2,3,4 Detects the line number errors. Does not detect the line number errors.
Page 14
2. ETHERNET ● UNIT SETUP (ERROR SETUP2) LV 58SER01A (SDI INPUT) Command Parameter1 Parameter2 Description SYS:UNIT:ERROR:ANC:PARITY 1,2,3,4 Detects the parity errors in the ancillary data. Does not detect the parity errors in the ancillary data. Queries the presence of parity error detection in the ancillary data.
Page 15
2. ETHERNET ● UNIT SETUP (ERROR SETUP3) LV 58SER01A (SDI INPUT) Command Parameter1 Parameter2 Description SYS:UNIT:ERROR:GAMUT:LPF 1,2,3,4 HD1M_SD1M Sets the LPF for gamut error detection to 1 MHz. HD2.8M_SD1M Sets the LPF for gamut error detection to 2.8 MHz as for HD-SDI and to 1 MHz as for SD-SDI.
Page 16
2. ETHERNET ● UNIT SETUP (ERROR SETUP4) LV 58SER01A (SDI INPUT) Command Parameter1 Parameter2 Description SYS:UNIT:ERROR:FREEZE 1,2,3,4 Detects the freeze errors. Does not detect the freeze errors. Queries the presence of freeze error detection. SYS:UNIT:ERROR:FREEZE:UPPER 1,2,3,4 0 to 100 Sets the detection area (upper) for freeze error.
Page 17
2. ETHERNET ● UNIT SETUP (ERROR SETUP5) LV 58SER01A (SDI INPUT) Command Parameter1 Parameter2 Description SYS:UNIT:ERROR:LEVEL 1,2,3,4 Detects the level errors. Does not detect the level errors. Queries the presence of level error detection. SYS:UNIT:ERROR:LEVEL:RUMA:UPPER 1,2,3,4 -51 to 766 Sets the upper limit (mV) of luminance level.
Page 18
2. ETHERNET ● WFM - INTEN/SCALE LV 58SER01A (SDI INPUT) Command Parameter1 Description WFM:INTEN:WFM -128 to 127 Adjusts the intensity of the video waveforms. Queries the intensity of the video waveforms. WFM:COLOR WHITE Sets the waveform display color to white. GREEN Sets the waveform display color to green.
Page 19
2. ETHERNET Command Parameter1 Description WFM:SWEEP:H_MAG In case of line display, set the sweep magnification so that the waveform fits on the screen. In case of line display, set the sweep magnification to x10 with respect to x1. In case of line display, set the sweep magnification to x20 with respect to x1.
Page 20
2. ETHERNET Command Parameter1 Description WFM:BLANKING:NORMAL REMOVE Displays the active period for the component display. H_VIEW Displays the active period and the horizontal blanking period for the component display. V_VIEW Displays the active period and the vertical blanking period for the component display.
Page 21
2. ETHERNET ● VECTOR LV 58SER01A (SDI INPUT) Command Parameter1 Description VECTOR Displays vector waveforms. ● VECTOR - INTEN/SCALE LV 58SER01A (SDI INPUT) Command Parameter1 Description VECTOR:INTEN:VECTOR -128 to 127 Sets the intensity of the vector waveform. Queries the intensity of the vector waveform. VECTOR:COLOR WHITE Sets the waveform display color to white.
Page 22
2. ETHERNET ● VECTOR - COLOR SYSTEM LV 58SER01A (SDI INPUT) Command Parameter1 Description VECTOR:MATRIX COMPONENT Sets the color matrix to component display. COMPOSITE Sets the color matrix to pseudo-composite display. Queries the color matrix setting. VECTOR:MATRIX:COMPOSITE: AUTO Selects NTSC or PAL automatically when displaying the FORMAT pseudo-composite.
Page 23
2. ETHERNET ● PICTURE LV 58SER01A (SDI INPUT) Command Parameter1 Description PICTURE Displays the pictures. ● PICTURE - ADJUST LV 58SER01A (SDI INPUT) Command Parameter1 Description PICTURE:BRIGHT -30 to 30 Adjusts the brightness of the picture display (%). Queries the brightness of the picture display. PICTURE:CONTRAST 0.70 to 1.30 Adjusts the contrast of the picture display.
Page 24
2. ETHERNET Command Parameter1 Description PICTURE:LINE_NUMBER Example) Sets the line of the line select. 1 to 1125 (Depending on the format) Queries the selected line of the line select. ● PICTURE - DISPLAY LV 58SER01A (SDI INPUT) Command Parameter1 Description PICTURE:SIZE Displays the picture size optimized.
Page 25
2. ETHERNET ● STATUS LV 58SER01A (SDI INPUT) Command Parameter1 Description STATUS Sets the status display. ● STATUS - EVENT LOG LV 58SER01A (SDI INPUT) Command Parameter1 Description STATUS:LOG Displays the error log screen. STATUS:LOG:LOG START Start the error log. STOP Stop the error log.
Page 26
2. ETHERNET ● STATUS - COUNTER LV 58SER01A (SDI INPUT) Command Parameter1 Description STATUS:COUNTER The error count is updated in unit of seconds, and it displays as number of times. FIELD The error count is updated in unit of fields, and it displays as number of times.
2. ETHERNET 2.4.3 LV 58SER02 Commands (EYE PATTERN unit) ● UNIT SETUP LV 58SER02 (EYE PATTERN unit) Command Parameter1 Parameter2 Description SYS:UNIT:ERROR:HD_AMP 1,2,3,4 (*1) Enables the amplitude error detection for HD. Disables the amplitude error detection for HD. Queries the presence of the amplitude error detection for HD.
Page 28
2. ETHERNET Command Parameter1 Parameter2 Description SYS:UNIT:ERROR:HD_TIMING_JIT:MAX 1,2,3,4 10 to 200 Sets the upper limit (%) of the timing jitter for HD. Queries the upper limit of the timing jitter for HD. SYS:UNIT:ERROR:HD_CURRENT_JIT 1,2,3,4 Detects the error of current jitter value for HD.
Page 29
2. ETHERNET Command Parameter1 Parameter2 Description SYS:UNIT:ERROR:SD_DELTA 1,2,3,4 Detects the error related to the difference between the rise time (Tr) and fall time (Tf) for SD. Does not detect the error (Tr-Tf) for Queries the presence of the error (Tr-Tf) detection for SD. SYS:UNIT:ERROR:SD_DELTA:MAX 1,2,3,4 40 to 140...
Page 30
2. ETHERNET ● EYE - EYE SETUP LV 58SER02 (EYE PATTERN unit) Command Parameter1 Description EYE:AUTO_MEASURE Automatically measures the eye pattern. Does not automatically measure the eye pattern. Queries the status of automatic measurement of eye pattern. EYE:GAIN:VAR Sets the gain of the eye pattern waveform to a constant value (×1).
Page 31
2. ETHERNET ● EYE - JITTER SETUP LV 58SER02 (EYE PATTERN unit) Command Parameter1 Description EYE:JITTER:PEAK_HOLD Holds the peak value of the jitter waveform. Does not hold the peak value of the jitter waveform. Queries the hold status of the peak value of the jitter waveform.
2. ETHERNET 2.4.4 LV 58SER03 Commands (COMPOSITE VIDEO INPUT) ● LV 58SER03 (COMPOSITE VIDEO INPUT) Command Parameter1 Description Displays the video signal waveform. ● WFM - INTEN/SCALE LV 58SER03 (COMPOSITE VIDEO INPUT) Command Parameter1 Description WFM:INTEN:WFM -128 to 127 Adjusts the intensity of the video waveforms. Queries the intensity of the video waveforms.
Page 33
2. ETHERNET Command Parameter1 Description WFM:SWEEP:V_MAG In case of field display, set the sweep magnification so that the waveform fits on the screen. In case of field display, set the sweep magnification to x20 with respect to X1. In case of field display, set the sweep magnification to x40 with respect to X1.
Page 34
2. ETHERNET ● VECTOR - INTEN/SCALE LV 58SER03 (COMPOSITE VIDEO INPUT) Command Parameter1 Description VECTOR:INTEN:VECTOR -128 to 127 Sets the intensity of the vector waveform. Queries the intensity of the vector waveform. VECTOR:COLOR WHITE Sets the waveform display color to white. GREEN Sets the waveform display color to green.
Page 35
2. ETHERNET ● VECTOR - COLOR SYSTEM LV 58SER03 (COMPOSITE VIDEO INPUT) Command Parameter1 Description VECTOR:MATRIX:SETUP Sets the setup to exclude. 7.5P Sets the setup to 7.5%. Queries the setup value. VECTOR:MATRIX:COLORBAR 100P Sets the scale that maches the 100% color bar. Sets the scale that maches the 75% color bar.
Page 36
2. ETHERNET Command Parameter1 Description PICTURE:BIAS:R -0.30 to 0.30 Adjusts the bias of the R signal (×100%). Queries the bias of the R signal. PICTURE:BIAS:G -0.30 to 0.30 Adjusts the bias of the G signal (×100%). Queries the bias of the G signal. PICTURE:BIAS:B -0.30 to 0.30 Adjusts the bias of the B signal (×100%).
2. ETHERNET 2.4.5 LV 58SER04 Commands (MPEG DECODER) ● UNIT SETUP LV 58SER04 (MPEG DECODER) Command Parameter1 Parameter2 Description SYS:UNIT:SEMI_AUTO 1,2,3,4 (*1) Sets the selection method of DECODE PID to an automatic setting. Sets the selection method of DECODE PID to a manual setting. Queries the selection method of DECODE PID.
Page 38
2. ETHERNET Command Parameter1 Parameter2 Description SYS:UNIT:ERROR:PCR 1,2,3,4 Detects the PCR error. Does not detect the PCR error. Queries the presence of detecting the PCR error. SYS:UNIT:ERROR:PCR:CYCLE 1,2,3,4 10 to 200 Sets the interval (msec) becoming the PCR error. Queries the interval becoming the PCR error.
Page 39
2. ETHERNET ● WFM - INTEN/SCALE LV 58SER04 (MPEG DECODER) Command Parameter1 Description WFM:INTEN:WFM -128 to 127 Adjusts the intensity of the video waveforms. Queries the intensity of the video waveforms. WFM:COLOR WHITE Sets the waveform display color to white. GREEN Sets the waveform display color to green.
Page 40
2. ETHERNET Command Parameter1 Description WFM:SWEEP:H_MAG In case of line display, set the sweep magnification so that the waveform fits on the screen. In case of line display, set the sweep magnification to x10 with respect to x1. ACTIVE In case of line display, magnifies and displays the waveform in the active interval.
Page 41
2. ETHERNET ● WFM - ARRANGE LV 58SER04 (MPEG DECODER) Command Parameter1 Description WFM:FILTER:NORMAL FLAT Sets the filter to Flat for the component display. LOWPASS Sets the filter to LPF for the component display. Queries the filter setting for the component display. WFM:FILTER:COMPOSITE FLAT Sets the filter to Flat and to parade display of the luminance...
Page 42
2. ETHERNET ● VECTOR LV 58SER04 (MPEG DECODER) Command Parameter1 Description VECTOR Displays vector waveforms. ● VECTOR - INTEN/SCALE LV 58SER04 (MPEG DECODER) Command Parameter1 Description VECTOR:INTEN:VECTOR -128 to 127 Sets the intensity of the vector waveform. Queries the intensity of the vector waveform. VECTOR:COLOR WHITE Sets the waveform display color to white.
Page 43
2. ETHERNET ● VECTOR - COLOR SYSTEM LV 58SER04 (MPEG DECODER) Command Parameter1 Description VECTOR:MATRIX COMPONENT Sets the color matrix to component display. COMPOSITE Sets the color matrix to pseudo-composite display. Queries the color matrix setting. VECTOR:MATRIX:COMPOSITE:FORMAT AUTO Selects NTSC or PAL automatically when displaying the pseudo-composite.
Page 44
2. ETHERNET ● PICTURE - MARKER LV 58SER04 (MPEG DECODER) Command Parameter1 Description PICTURE:MARKER:4_3 Displays the 4:3 aspect marker. Does not display the 4:3 aspect marker. Queries the presence of displaying the 4:3 aspect marker. PICTURE:MARKER:16_9 Displays the 16:9 aspect marker. Does not display the 16:9 aspect marker.
2. ETHERNET 2.4.6 LV 58SER40A Commands (DIGITAL AUDIO) ● UNIT SETUP LV 58SER40A (DIGITAL AUDIO) Command Parameter1 Parameter2 Description SYS:UNIT:EXT_BNC 1,2,3,4 (*1) INPUT Sets all rear BNC connector to input. OUTPUT Sets all rear BNC connector to output. Queries all rear BNC connector setting. SYS:UNIT:ERROR:LEVEL_OVER 1,2,3,4 Detects the level over error.
Page 46
2. ETHERNET ● AUDIO - CHANNEL SELECT LV 58SER40A (DIGITAL AUDIO) Command Parameter1 Description AUDIO:CH_SEL:NUMBER Sets the number of measurement channels to 8ch. 16CH Sets the number of measurement channels to 16ch. Queries the number of measurement channels. AUDIO:CH_SEL:DISPLAY 1_8CH Sets the channels that are measured to 1-8ch when the number of measurement channels is 8ch.
Page 47
2. ETHERNET Command Parameter1 Description AUDIO:METER:OVER_LEVEL -40.0 to 0.0 Sets the over level.(dBFS) Queries the over level. AUDIO:METER:WARNING_LEVEL -40.0 to 0.0 Sets the warning level. (dBFS) Queries the warning level. AUDIO:METER:REF_LEVEL -40.0 to 0.0 Sets the reference level. (dBFS) Queries the reference level. ●...
Page 48
2. ETHERNET Command Parameter1 Description AUDIO:LISSAJOU:MAP:MULTI_L3 CH1 to CH16 Sets the channel to be assigned to the L3 axis of the multi Lissajous waveform. Queries the channel to be assigned to the L3 axis of the multi Lissajous waveform. AUDIO:LISSAJOU:MAP:MULTI_R3 CH1 to CH16 Sets the channel to be assigned to the R3 axis of the multi Lissajous waveform.
Page 49
2. ETHERNET ● AUDIO - S.IMAGE SETUP LV 58SER40A (DIGITAL AUDIO) Command Parameter1 Description AUDIO:S_IMAGE:INTEN:S_IMAGE -128 to 127 Sets the intensity of the sound image waveform. Queries the intensity of the sound image waveform. AUDIO:S_IMAGE:INTEN:SCALE -8 to 7 Sets the intensity of the scale. Queries the intensity of the scale.
Page 50
2. ETHERNET ● AUDIO - STATUS SETUP LV 58SER40A (DIGITAL AUDIO) Command Parameter1 Description AUDIO:STATUS:DISPLAY DEFAULT Displays the status screen. CH_STATUS Displays the channel status screen. USER_BIT Displays the user bit screen. Queries the display formt of the status screen. AUDIO:DOLBY:E_META_PRM PRM1 to PRM8 Sets the program number in which metadata of the Dolby E...
Page 51
2. ETHERNET Command Parameter1 Description AUDIO:LOUD:SHORT:AVRG_TIME 200 to 10000 Sets the measurement time of short-term loudness (100 steps). Queries the measurement time of short-term loudness. AUDIO:LOUD:MOMENT:AVRG_TIME 200 to 10000 Sets the measurement time of momentary loudness (100 steps). Queries the measurement time of momentary loudness. AUDIO:LOUD:RESPONSE SHORTTERM Sets the response model to short-term.
Page 52
2. ETHERNET Command Parameter1 Description AUDIO:LOUD:MAP:RL CH1 to CH16 Selects the channel to assign to sub Lch. Queries the channel to assign to sub Lch. AUDIO:LOUD:MAP:RR CH1 to CH16 Selects the channel to assign to sub Rch. Queries the channel to assign to sub Rch. AUDIO:LOUD:SHORTTERM:DATA:MAI Queries the main short-term loudness.
Page 53
2. ETHERNET Command Parameter1 Description AUDIO:DOLBY:AUX_CH LTRT Sets the function of the AUX CH to LtRt. LORO Sets the function of the AUX CH to LoRo. MONO Sets the function of the AUX CH to MONO. MUTE Sets the function of the AUX CH to MUTE. Sets the function of the AUX CH.
2. ETHERNET FTP Commands Carries out the FTP command after carrying out the MAKE command of TELNET to retrieve each file by using the FTP. Example) Operation of retrieving a text file of the event log to a computer 1) Starts TELNET and carries out "MAKE LOG" of the TELNET command. 2) Starts FTP and carries out “GET”...
3. SNMP SNMP Description SNMP (Simple Network Management Protocol) can be used to control the LV 5800(A) and notify SDI signal errors. The following sections describe how to set the LV 5800(A) and MIB (Management Information Base) when using SNMP. SNMP Version Supported The LV 5800(A) supports SNMPv1.
SNMP manager to the MIB object below. The number of destinations that can be connected has been expanded from one to four locations. ・IP address of TRAP transmission destination 1 1.3.6.1.4.1.leader(20111).lv5800(10).lv5800ST1(1).l10trapTBL(9).l10tr apIpTBL(2).l10trapIp1TBL(1).l10trapManagerIp1(1).0 ・IP address of TRAP transmission destination 2 1.3.6.1.4.1.leader(20111).lv5800(10).lv5800ST1(1).l10trapTBL(9).l10tr apIpTBL(2).l10trapIp2TBL(2).l10trapManagerIp2(1).0...
3. SNMP This section describes the MIB (Management Information Base) that the LV 5800(A) uses. The indications in the ACCESS column in the tables are defined as follows: Information that can be retrieved using the SNMP manager. Information that can be retrieved and set using the SNMP manager. R/WO Information that can be retrieved and set using the SNMP manager.
Page 58
3. SNMP ● system group SYNTAX ACCESS SUPPORT sysDescr system.1 DisplayString ○ sysObjectID system.2 ObjectID ○ sysUpTime system.3 TimeTicks ○ sysContact (*1) system.4 DisplayString ○ sysName (*1) system.5 DisplayString ○ sysLocation (*1) system.6 DisplayString ○ sysServices system.7 INTEGER ○ *1 Set using up to 40 bytes. ●...
3. SNMP 3.4.2 Enterprise MIB ● Enterprise Number The enterprise number of LEADER ELECTRONICS CORPORATION is 20111. iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).leader(20111) ● Retrieving the Enterprise MIB File Download the file on the LV 5800(A) using FTP. The file name is “lv5800.my”. For a description of how to use FTP, see section 2.2, “FTP File Transfer” in this Manual.
3. SNMP 3.5.3 Variable Binding List ● index 1 OID: leader(20111).lv5800(10).lv5800ST1(1).trapTBL(9).trapStrTBL(1).1.0 Syntax: Counter Range: 1 to 4294967295 (overflow occurs if this range is exceeded) Description: The total number of enterprise traps sent after starting up. ● index 2 OID: leader(20111).lv5800(10).lv5800ST1(1).trapTBL(9).trapStrTBL(1).2.0...
Page 93
3. SNMP List of format information List of error information for TRAP for TRAP Syntax Format Syntax Description 1080i/60 1080i/60 CRC_Y_ERR CRC error detection (LUMA) 1080sF/30 1080sF/30 CRC_C_ERR CRC error detection (CHROMA) 1080i/59.94 1080i/59.94 EDH_ERR EDH error detection 1080sF/29.97 1080sF/29.97 TRS_P_ERR TRS error detection (POS) 1080i/50...
FIRMWARE REVISION HISTORY This manual was written for the following firmware versions: ・ Ver. 1.2 on the LV 5800A ・ Ver. 11.1 on the LV 5800 To confirm the version, press a key in order of SYS => F•5 SYSTEM INFORMATION.
Need help?
Do you have a question about the LV 5800A and is the answer not in the manual?
Questions and answers