Table of Contents
Advertisement
1. KNOW YOUR TOOL
Read and understand the owners manual and labels affixed to the
tool. Learn its application and limitations as well as its specific
potential hazards.
2. GROUND THE TOOL.
This tool is equipped with an approved 3-conductor cord and a
3-prong grounding type plug to fit the proper grounding type
receptacle. The green conductor in the cord is the grounding wire.
NEVER connect the green wire to a live terminal.
3. KEEP GUARDS IN PLACE.
Keep in good working order, properly adjusted and aligned.
4. REMOVE ADJUSTING KEYS AND
WRENCHES.
Form habit of checking to see that keys and adjusting wrenches
are removed from tool before turning it on.
5. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents. Make sure the floor
is clean and not slippery.
6. AVOID DANGEROUS ENVIRONMENT.
Don't use power tools in damp or wet locations or expose them to
rain. Keep work area well lit and provide adequate surrounding
work space.
7. KEEP CHILDREN AWAY.
All visitors should be kept a safe distance from work area.
8. MAKE WORKSHOP CHILD-PROOF.
-with padlocks, master switches or by removing starter keys.
9. USE PROPER SPEED.
A tool will do a better and safer job when operated at the proper
speed.
10. USE RIGHT TOOL.
Don't force the tool or the attachment to do a job for which it was
not designed.
11. WEAR PROPER APPAREL.
Do not wear loose clothing, gloves, neckties or jewelry (rings,
SPECIFIC SAFETY RULES
Safety is a combination of common sense, staying alert and knowing
how your bandsaw works. Read and understand the following safety
rules before operating.
1) Adjust the upper guide to just clear workpiece.
2) Make sure that the blade is properly adjusted and tensioned before
operating.
3) Do not remove small jammed pieces until the blade has completely
stopped.
4) Hold item to cut firmly against the table.
5) Turn the machine off if the piece to cut is to be backed out of an
uncompleted cut.
6) Do not operate this bandsaw using a dull or worn blade.
7) After cutting meat, always sanitize and clean all exposed parts.
BEFORE EACH USE:
Inspect your bandsaw.
1) To reduce the risk of injury from accidental starting, turn the switch
off, unplug the bandsaw and remove the switch key before
changing the set-up, removing covers, guards or the blade.
2) Check the alignment of moving parts, binding of moving parts,
GENERAL & SPECIFIC
SAFETY RULES
12. ALWAYS WEAR SAFETY GLASSES.
13. DON'T OVERREACH.
14. MAINTAIN TOOL WITH CARE.
15. DISCONNECT TOOLS.
16. AVOID ACCIDENTAL STARTING.
17. USE RECOMMENDED ACCESSORIES.
18. NEVER STAND ON TOOL.
19. CHECK DAMAGED PARTS.
20. NEVER LEAVE MACHINE RUNNING
3) If any part is missing, bent or broken in any way, or if any electrical
4) Make sure the blade teeth point downward, towards the table.
5) Make sure the blade guides are properly adjusted.
6) Make sure the blade tension is properly adjusted.
7) To reduce the risk of accidental blade contact, minimize blade
8) Before starting your cut, watch the saw while it runs. If it makes an
9) Let the blade reach full speed before cutting.
watch) because they could get caught in moving parts. Non-slip
footwear is
recommended. Wear protective hair covering to
contain long hair. Roll up long sleeves above the elbows.
Always wear safety glasses (ANSI Z87.1). Everyday eye-glasses
only have impact resistant lenses, thet are NOT safety glasses.
Also use a face or dust mask if cutting operation is dusty.
Keep proper footing and balance at all times.
Keep tools sharp and clean for best and safest performance.
Follow instructions for lubricating and changing accessories.
Before servicing, when changing accessories or attachments.
Make sure the swich is in the ''OFF'' position before plugging in.
Consult the manual for recommended accessories. Follow the
instructions that accompany the accessories. The use of improper
accessories may cause hazards.
Serious injury could occur if the tool tips over. Do not store materials
such that it is necessary to stand on the tool to reach them.
Before further use of the tool, a guard or other parts that are
damaged should be carefully checked to ensure that they will
operate properly and perform their intended function. Check for
alignment of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other
parts that are damaged should be properly repaired or replaced.
UNATTENDED.
Turn power ''OFF''. Don't leave any tool running until it comes to a
complete stop.
breakage of parts, bandsaw stability and any other conditions that
may affect the way the bandsaw works.
parts do not work properly, turn the bandsaw off and unplug the
saw. Replace damaged or missing parts before using the bandsaw
again.
breakage and provide maximum blade support, always adjust the
upper blade guide and blade guard to just clear the workpiece.
unfamiliar noise or vibrates a lot, stop immediately. Turn the saw off
and unplug. Do not restart until you have found and corrected the
problem.
Advertisement
Table of Contents
