CaryMart S1UD-DC06 Manual

RF Wireless Remote Control Radio Controller with Delay Time Function / Transmitter & Receiver

Package Include:

8 x Receiver: S1UD-DC06 / S1UD-DC09 / S1UD-DC12 / S1UD-DC24 (1 Channel / Three Control Modes)
1 x Transmitter: CV-8
1 x User manual

Feature:

Wireless control, easy to install
Setting delay time from 0 to 99 seconds.
Control Lights, Motors, Fans, electrically operated Doors/Locks/Windows/Blinds/Cars or Other Appliances with voltage AC110~240V or
DC0~28V.
You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass
through walls, floors and doors.
With characteristics of reverse power protection.
Use an 8-bit microcontroller with low-power and high-speed CMOS technology.
Reliable control: The transmitter (Encoding) and the receiver (Decoding) use an 8-bit code.
One/ several transmitters can control one/ several receivers simultaneously.
If you use two or more receivers in the same place, you can set them with different codes.
Transmitting Frequency: 315MHz / 433MHz

Receiver:

Model No.: S1UD-DC06 / S1UD-DC09 / S1UD-DC12 / S1UD-DC24
Channel: 1 CH
Control Modes: Toggle, Momentary, Latched
Delay time: 0~99 seconds
Coding Type: Fixed code or Learning code
Coding Setting: By learning
Power Supply (Operating Voltage): DC6V (S1UD-DC06), DC12V±1V (S1UD-DC12), DC9V±1V (S1UD-DC09), DC24V±2V (S1UD-DC24)
Working Voltage Range of Relay: AC110~240V or DC0~28V
Output: Relay output (Normally open and normally closed)
Maximum Working Current of Relay: 7A
PCB Size: 45mm x 30mm x 15mm
Case Size: 50mm x 35mm x 23mm
Receiver Sensitivity:-114dbm
Static Current: ≤10mA

Transmitter:

Model No.: CV-8
Channel: 8 CH
Remote Control Distance: 500m / 1500ft (theoretically)
Encode: Fixed code by Soldering
Unit size: 110mm x 50mm x 18mm
Power Supply: 1 x 23A -12V battery (Included, can be used for 12 months)

Usage:

Initial state: Terminals A, B = Normally Closed; Terminals B, C = Normally Open.
Connect device to terminal "B & C"; connect power supply to terminal "+" and "-".
Setting different control modes (We have set the receiver as Toggle control mode before delivery. If you want to use other control modes, do as
following operation):
Setting control mode Toggle: Connect Jumper-2 and Jumper-3.
Control mode Toggle: Press -> On; Press again -> Off.
Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)
Press button 1 again: Turn off Receiver 1 (disconnect B and C, connect A and B)
If you set delay time, such as 30 seconds:
Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)
After 30 seconds, Turn off Receiver 1 automatically (disconnect B and C, connect A and B). Or press button 1 again within 30 seconds: Turn off
Receiver 1 immediately.
...
Press button 8: Turn on Receiver 8 (connect B and C, disconnect A and B)
Press button 8 again: Turn off Receiver 8 (disconnect B and C, connect A and B)
If you set delay time, such as 30 seconds:
Press button 8: Turn on Receiver 8 (connect B and C, disconnect A and B)
After 30 seconds, Turn off Receiver 8 automatically (disconnect B and C, connect A and B). Or press button 8 again within 30 seconds: Turn off
Receiver 8 immediately.
Setting control mode Momentary: Disconnect Jumper.
SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: sale@carymart.com