Roland GR-33 Owner's Manual page 71

34: EH DLY (Enhancer
This effect connects an enhancer and delay in series.
fig.6-37
L in
Enhancer
Mix
R in Enhancer
Mix
EH SENS (Enhancer sensitivity) 0–127
Specify the sensitivity of the enhancer.
EH MIX (Enhancer mix level) 0–127
Specify the volume of the overtones generated by the
enhancer, relative to the original sound.
DLY TIME (Delay time) 0.0–500 ms
Specify the time delay from the original sound until the delay
sound is heard.
DLY FEEDBACK (Delay feedback level) -98–+98 % #
Specify the proportion (%) of the delay sound that is to be
returned to the input.
Positive (+) settings will return the sound to the input with
the original phase, while negative (-) settings produce an
inverted phase.
You can set a value from -98% to +98%, in steps of 2%. There
is no feedback when the value is zero.
DLY HF DAMP (Delay HF damp)
200/250/315/400/500/630/800/1000/1250/1600/2000/2500/3150/
4000/5000/6300/8000 (200–8000 Hz), Bypass
Specify the frequency at which the high frequency range of
the delayed sound returned to the input will be cut.
If you do not want the sound to be cut, select Bypass.
DLY BALANCE (Delay balance) D100:0E–D0:100E
Specify the volume balance between the enhancer sound that
does not pass through the delay and the enhancer sound that
does pass through the delay.
A setting of D100:0E will output only the enhancer sound,
and a setting of D0:100E will output only the enhancer sound
that is passed through the delay.
LEVEL (Output level) 0–127
Specify the output volume.
Delay)
L out
Balance D
Balance E
Delay
Balance E
Feedback
R out
Balance D
Chapter 6 Using the Built-in Effects
35: CHO DLY (Chorus
This effect connects a chorus and a delay in series.
fig.6-38
Balance D
L in
Balance E
Chorus
Balance E
R in
Balance D
CHO PRE DELAY (Chorus pre delay time) 0.0–100 ms
Specify the time delay from the original sound until the
chorus sound is heard.
CHO RATE (Chorus rate) 0.05–10.0 Hz #
Specify the modulation frequency of the chorus sound.
CHO DEPTH (Chorus depth) 0–127
Specify the modulation depth of the chorus sound.
CHO BALANCE (Chorus balance) D100:0E–D0:100E
Specify the volume balance between the original sound and
the chorus sound.
With a setting of D100:0E only the original sound will be
output, and with a setting of D0:100E only the chorus sound
will be output.
DLY TIME (Delay time) 0.0–500 ms
Specify the time delay from the original sound until the delay
sound is heard.
DLY FEEDBACK (Delay feedback level) -98–+98 %
Specify the proportion (%) of the delay sound that is to be
returned to the input.
Positive (+) settings will return the sound to the input with
the original phase, while negative (-) settings produce an
inverted phase.
You can set a value from -98% to +98%, in steps of 2%. There
is no feedback when the value is zero.
DLY HF DAMP (Delay HF damp)
200/250/315/400/500/630/800/1000/1250/1600/2000/2500/3150/
4000/5000/6300/8000 (200–8000 Hz), Bypass
Specify the frequency at which the high frequency range of
the delayed sound returned to the input will be cut.
If you do not want the sound to be cut, select Bypass.
DLY BALANCE (Delay balance) D100:0E–D0:100E
Specify the volume balance between the chorus sound that
passes through the delay and the chorus sound which does
not pass through the delay.
With a setting of D100:0E only the chorus sound will be
output, and with a setting of D0:100E only the chorus sound
that passes through the delay will be output.
Delay)
L out
Balance D
Balance E
Delay
Balance E
Feedback
R out
Balance D
71