kozy heat BELLINGHAM 44 Installation And Operation Manual

kozy heat BELLINGHAM 44 Installation And Operation Manual

Direct vent gas fireplace
Hide thumbs Also See for BELLINGHAM 44:
Table of Contents

Advertisement

Quick Links

HUSSONG MANUFACTURING CO., INC.
B E L L I N G H A M 4 4
Model #BHM-44
Direct Vent Gas Fireplace
English and French installation manuals are available through your
local dealer. Visit our website www.kozyheat.com.
Les manuels d'installation en français et en anglais sont disponibles
chez votre détaillant local. Visitez www.kozyheat.com .
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
ͷ Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
ͷ WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do
not use any phone in your building.
• Leave the building immediately.
• Immediately call your gas supplier from
a neighbor's phone. Follow the gas
supplier's instructions.
• If you cannot reach your gas supplier,
call the fire department.
ͷ Installation and service must be performed
by a qualified installer, service agency or
the gas supplier.
Hussong Mfg. Co., Inc.
BHM-44 Report No: 20-605
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
INSTALLATION AND
OPERATION MANUAL
This
appliance
an
aftermarket,
manufactured home (USA only) or mobile
home, where not prohibited by local codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with other
gases, unless a certified kit is used.
DANGER
A barrier designed to reduce the risk of burns
from the hot viewing glass is provided with this
appliance and shall be installed for the protection
of children and other at-risk individuals.
may
be
installed
permanently
located,
HOT GLASS WILL
CAUSE BURNS
DO NOT TOUCH GLASS
UNTIL COOLED
NEVER ALLOW CHILDREN
TO TOUCH GLASS
Rev.1, August 2020
Starting Serial Number: 20 200000 36
in

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BELLINGHAM 44 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for kozy heat BELLINGHAM 44

  • Page 1 INSTALLATION AND OPERATION MANUAL HUSSONG MANUFACTURING CO., INC. B E L L I N G H A M 4 4 Model #BHM-44 Direct Vent Gas Fireplace English and French installation manuals are available through your local dealer. Visit our website www.kozyheat.com. Les manuels d’installation en français et en anglais sont disponibles chez votre détaillant local.
  • Page 3 Please retain this owner’s manual for future reference. CON GRAT ULAT I ON S! We welcome you as a new owner of a Kozy Heat gas fireplace. Kozy Heat products are designed with superior components and materials, and assembled by trained craftsmen who take pride in their work.
  • Page 5: Table Of Contents

    7.3 Natural Draft Vent Restriction ............... 44 LIMITED LIFETIME WARRANTY ............ 75 7.4 Natural Draft Installation ................45 7.5 Class A Chimney/Masonry Chimney Conversion ......48 #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces TABLE OF CONTENTS 5...
  • Page 7: Introduction

    Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified. #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces INTRODUCTION 7...
  • Page 8: Specifications

    Verify the household breaker is shut off prior to working on any electrical lines. • The AC power supply to this appliance must be hot at all times and shall not have a switch installed in it. 8 SPECIFICATIONS Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 9: Appliance Dimensions

    (349mm) Access ¾ ” (120mm) ⁄ ” ⁄ ” (450mm) (1286mm) Power Vent Wire Harness Hole (see KPV manual for more information) Figure 2.1, BHM-44 Dimensions #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces SPECIFICATIONS 9...
  • Page 10: Safety Barrier Screen Dimensions

    For installation instructions, refer to Section 4.2 Safety Barrier Installation on page 35. ⁄ ” (1102mm) ⁄ ” (606mm) Safety Barrier Screen (only) BH44-ES Figure 2.2, Safety Barrier Screen Dimensions 10 SPECIFICATIONS Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 11: Framing

    See Section 8.5 Control Board Access, Removal and Installation on page 53 for access to the control board before and after installation. #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FRAMING 11...
  • Page 12: Nailing Flange Assembly And Installation

    Front View Top View Nailing ange Stand-o ange Framing stud Framing stud Nailing ange ½ ” (89mm) clearance ALL DESIGN OPTIONS INSTALLATION Figure 3.2, Nailing Flange Installation 12 FRAMING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 13: Stand-Off Assembly And Header Heat Shield

    Contact point for non-combustible material above the fireplace • Attachment for the header heat shield STANDARD AND VENTED CAVITY INSTALLATIONS ONLY Figure 3.3, Standard Installation for Stand-off Assembly and Header Heat Shield #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FRAMING 13...
  • Page 14: Clearances To Combustibles

    ½ ” (572mm) ¼ ” (1123mm) ½ ” ½ ” ⁄ ” (1588mm) (2248mm) 2” (1463mm) (51mm) ALL DESIGN OPTIONS INSTALLATION Figure 3.4, Clearance to Combustibles 14 FRAMING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 15: Rough Framing

    ” (2235mm) ¼ ” (1463mm) (1175mm) 22” ¼ ” (558mm) (1175mm) ALL DESIGN OPTIONS INSTALLATION Figure 3.5, Standard Installation Rough Opening Dimensions and TV Recess Construction #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FRAMING 15...
  • Page 16: Natural Draft Vent Termination Rough Framing

    Please consult the vent manufacturer’s instructions to determine the elbow dimension used for installation. Adjust the wall pass-through rough opening dimensions to maintain clearance requirements. 16 FRAMING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 17 Figure 3.6, Vent Termination Minimum Framing Clearances Natural gas and propane Natural draft minimum horizontal terminations 22” (558mm) ¾ ” (1721mm) ALL DESIGN OPTIONS INSTALLATION Figure 3.7, Vent Termination Minimum Framing Dimensions #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FRAMING 17...
  • Page 18: Outdoor Covered Fireplace Installation

    5’ (1.5m) or greater. The width of the overhang to EACH side of the replace (C) must be 5’ or greater. ALL DESIGN OPTIONS INSTALLATION Figure 3.8, Outdoor Covered Fireplace Install - 1 18 FRAMING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 19 OUTSIDE INSIDE Free standing structure (weatherproof enclosure) ALL DESIGN OPTIONS INSTALLATION Figure 3.9, Outdoor Covered Installation 2 (your fireplace may look different than the one shown) #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FRAMING 19...
  • Page 20: Exterior And Interior Heat Transfer Kit Cover Plates

    Remove (1) square cover plate per kit, up to (2) kits may be used. See heat transfer kit manuals (HTK-EXT/HTK-INT) for more information Figure 3.10, Heat Transfer Kit Cover Plate Removal 20 FRAMING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 21: Vented Cavity And Komfort Zone Kit Installation

    Remove (2) cover plate for a Komfort Zone Kit or vented cavity options for the front or top vent cavity Figure 3.13, Convection Baffle Removal Figure 3.11, Cover Plate Removal #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FRAMING 21...
  • Page 22 Remove (4) screws securing the header heat shield to the stand- off assembly. Discard header heat shield KZK INSTALLATIONS ONLY Figure 3.14, Komfort Zone Kit Installation for Stand-off Assembly 22 FRAMING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 23 60” (1524mm) Ceiling Air Discharge Opening VENTED CAVITY INSTALLATIONS ONLY Figure 3.15, Clearance from Air Discharge Opening to Sprinkler Head #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FRAMING 23...
  • Page 24 (1118mm) 44” (1118mm) VENTED CAVITY INSTALLATIONS ONLY VENTED CAVITY INSTALLATIONS ONLY Figure 3.16, Front Vented Cavity Installation Figure 3.17, Vented Cavity Rear to Adjacent Room Installation 24 FRAMING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 25 (2235mm) Enclosure *must maintain 3” (76mm) clearance for full length of crown molding/trim projection VENTED CAVITY INSTALLATIONS ONLY Figure 3.19, Front Vented Cavity Crown Molding Installation #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FRAMING 25...
  • Page 26 44” Air discharge overhang (101mm) (1118mm) 6” Air discharge opening (152mm) 52” (1321mm) VENTED CAVITY INSTALLATIONS ONLY Figure 3.20, Front Vented Cavity Alternative Installation with Overhang 26 FRAMING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 27 Requires a minimum1½” (38mm) clearance from replace enclosure top to ceiling on all three sides ½ ” (38mm) ½ ” (38mm) ½ ” (38mm) VENTED CAVITY INSTALLATIONS ONLY Figure 3.21, Top Vented Cavity Installation #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FRAMING 27...
  • Page 28 Air discharge overhang Air discharge opening 6” (152mm) Width of replace chamber 8” (203mm) VENTED CAVITY INSTALLATIONS ONLY Figure 3.23, Top Vented Cavity Alternative Installation with Overhang 28 FRAMING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 29: Facing And Finishing

    Screws can only penetrate the fireplace outer shell up to 1/2" (13mm) in the allowed areas. #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FACING AND FINISHING 29...
  • Page 30 (635mm) ½ ” (699mm) ½ ” (64mm) Bottom nishing edge 14” (356mm) Combustible Floor STANDARD INSTALLATION Figure 4.1, Standard Installation Combustible Mantel and Hearth 30 FACING AND FINISHING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 31 ONLY 6” (152mm) 6” (152mm) 88” Top nishing edge (2235mm) ½ ” (851mm) Combustible Floor STANDARD INSTALLATION Figure 4.2, Standard Installation Non-combustible Mantel Clearances #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FACING AND FINISHING 31...
  • Page 32 Finishing Edge (25mm) 3” 1” (76mm) (25mm) 88” 6” (2235mm) (152mm) unlimited 3” (76mm) 6” (152mm) STANDARD INSTALLATION Figure 4.3, Standard Adjacent Sidewall Clearances 32 FACING AND FINISHING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 33 ⁄ ” (1129mm) ⁄ ” ⁄ ” (632mm) (167mm) ½ ” (63mm) ⁄ ” (1464mm) ALL DESIGN OPTIONS INSTALLATION Figure 4.4, Framed Opening Clearances #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FACING AND FINISHING 33...
  • Page 34 ⁄ ” (633mm) ½ ” (1130mm) ½ ” (63mm) Non-combustible material only Combustible material allowed ALL DESIGN OPTIONS INSTALLATION Figure 4.5, Minimum Finishing Dimensions 34 FACING AND FINISHING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 35: Safety Barrier Installation

    • To remove safety barrier screen: lift the screen up and out of slots. Recessed mount Flush mount Figure 4.6, Safety Screen Installation #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FACING AND FINISHING 35...
  • Page 36: Vented Cavity And Kzk Facing And Finishing Requirements

    • For a painted surface, use a high quality acrylic latex primer and finish coat. Avoid flat or light-colored paints to prevent discoloring. 36 FACING AND FINISHING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 37 Bottom (64mm) nishing edge 14” (356mm) Combustible Floor VENTED CAVITY AND KZK INSTALLATIONS ONLY Figure 4.7, Vented Cavity & KZK Facing and Finishing Clearances #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FACING AND FINISHING 37...
  • Page 38 1” (25mm) 88” 6” (2235mm) (152mm) unlimited 6” (152mm) VENTED CAVITY AND KZK INSTALLATIONS ONLY Figure 4.8, Vented Cavity and KZK Adjacent Sidewall Clearances 38 FACING AND FINISHING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 39 88” Top nishing edge (2235mm) Bottom nishing edge VENTED CAVITY AND KZK INSTALLATIONS ONLY Figure 4.9, Combustible Wall Finish up to 1" (25mm) thick #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FACING AND FINISHING 39...
  • Page 40: Gas Line Connection

    5” WC (1.25 kPa) 10.5” WC (2.62 kPa) 7” WC (1.74 kPa ) recommended Propane 12” WC (2.99 kPa) 13” WC (3.24 kPa) recommended 40 GAS LINE CONNECTION Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 41: Natural Draft Termination Locations

    Over 12/12 to 14/12 1.52 Over 14/12 to 16/12 1.83 Over 16/12 to 18/12 2.13 Over 18/12 to 20/12 2.27 Over 20/12 to 21/12 2.44 #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces NATURAL DRAFT TERMINATION LOCATIONS 41...
  • Page 42: Minimum Natural Draft Vent Termination Clearances

    Manufacturing Co., Inc. will not be held responsible for heat damage caused from terminating under vinyl overhangs, vinyl ceilings, or vinyl ventilated/unventi- lated soffits. 42 NATURAL DRAFT TERMINATION LOCATIONS Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 43: Venting

    This appliance is equipped for use with a 5” (127mm) exhaust by 8” (203mm) air intake co-axial vent pipe system. American Metal Products 4DHCS This appliance is approved for use for Kozy Heat Power Venting #KPV (Ameri-Vent) 4DHC (sold separately).
  • Page 44: Natural Draft Vent Restriction

    Remove all inner rings for the least restriction Insert restrictor plate into 5” (127mm) exhaust pipe in firebox ceiling with tabs facing towards you Figure 7.1, Restrictor Plate Installation 44 VENTING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 45: Natural Draft Installation

    (4) 45° elbows may be used. No 90° elbows are allowed. For every 45° elbow used, 18” (457mm) must be subtracted from maximum venting allowed. 36” (914mm) 50’ (15.24m) 36” (914mm) #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces VENTING 45...
  • Page 46 (D) Termination Cap 8’ 6” (2.44m) (152mm) 24” 6” (610mm) (152mm) 36” (914mm) 24” (610mm) 12’ 25’ (3.66m) (7.62m) 6” 6” (152mm) (152mm) 48” 25’ (1219mm) (7.62m) 46 VENTING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 47 Section 7.1 Approved Vent Systems on page • (2) 45° degree elbows may be used in place of (1) 90° elbow. Figure 7.2, Natural Gas and Propane Natural Draft Combination Venting #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces VENTING 47...
  • Page 48: Class A Chimney/Masonry Chimney Conversion

    90° horizontal elbow + reducer + retro connector + 10’ (3.05m) minimum length of 4” aluminum flexible pipe / 50’ (15.24m) maximum length of 4” aluminum flexible pipe + top adapter + termination cap 48 VENTING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 49: Fireplace Setup

    PROVIDED LATCH TOOL ATTACHED VALANCE AGAINST UNIT TO TOP LATCH ASSEMBLY TWO LATCHES SECURING VALANCE Figure 8.2, Gas Valve Access Cover Plate Figure 8.1, Glass Frame Assembly Removal #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FIREPLACE SETUP 49...
  • Page 50: Panel Installation

    Figure 8.3, Back Refractory Panel Installed Figure 8.5, Side Black Glass Panels Installed Figure 8.4, Side Refractory Panel Installed 50 FIREPLACE SETUP Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 51: Bh44-500 Log Set Installation

    Studs for log BH44-3 Studs for log BH44-2 Studs for log BH44-4 Log stop bracket Figure 8.6, Burner Stud Locations and Log Stop Brackets Figure 8.7, Base Logs #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FIREPLACE SETUP 51...
  • Page 52 Align log BH44-9 with the notches on log BH44-1 (Figure 8.8) and log BH44-4, as shown in Figure 8.9. Figure 8.8, Base Log Notches Figure 8.9, Completed Install 52 FIREPLACE SETUP Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 53: Control Board Access, Removal And Installation

    Figure 8.11, Control Board Removal and Installation - 1 side burners. Release the burner tube venturis off of the burner orifices and remove from firebox. Instructions continue on the next page. #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FIREPLACE SETUP 53...
  • Page 54 15. Turn the manual valve counterclockwise to the ON position. 16. Reconnect electrical power. 17. Verify proper log placement, operation of fireplace, and any electrical components. 54 FIREPLACE SETUP Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 55: Electrical Information

    National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1. Figure 9.1, Wiring Schematics #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces ELECTRICAL INFORMATION...
  • Page 56: Outlet Junction Box

    Remove the media tray. Install (6) halogen bulbs (included in component packet) into lamp bases. Reinstall media tray. Reinstall glass frame assembly and safety barrier. 56 ELECTRICAL INFORMATION Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 57: Top Light Kit #600-Tlk

    Figure 9.3, Top Light Kit Location YELLOW FEMALE CONNECTORS RED MALE CONNECTORS BLUE FEMALE CONNECTORS RED MALE CONNECTORS (from control module) Figure 9.4, Top Light Kit Wiring #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces ELECTRICAL INFORMATION...
  • Page 58: Operating Instructions

    This fireplace may produce noises of varying degree as it heats and cools due to metal expansion and contraction. This is normal, and does not affect the performance or longevity of the fireplace. 58 OPERATING INSTRUCTIONS Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 59: Setup Proflame

    Once replaced, the IFC module will emit a ‘beep’ as soon as it is powered. Remote learn button ON/OFF toggle switch Figure 10.1, ON/OFF Toggle Switch and Remote Learn Button Location #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces OPERATING INSTRUCTIONS 59...
  • Page 60: Control System 7 Day Timeout

    Press the remote control down arrow key during flame adjustment mode to reduce the flame to OFF (indicated by OFF displayed on the LCD screen). 60 OPERATING INSTRUCTIONS Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 61: Remote Control Operation

    LCD screen. Simultaneously press the mode key and the up arrow key to activate or deactivate this function. #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces OPERATING INSTRUCTIONS 61...
  • Page 62 HI. A single ‘beep’ will confirm reception of the command. Flame Off Flame Level 1 Flame Level 5 Flame Level Maximum 62 OPERATING INSTRUCTIONS Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 63 The temperature bulb graphic will not be displayed on the LCD screen. • To reactivate remote thermostat operation, follow the same key sequence procedure above. The temperature bulb graphic will reappear on the LCD screen. #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces OPERATING INSTRUCTIONS 63...
  • Page 64 Press the up arrow key to turn the ember bed light kit ON. Press the down arrow key to turn the ember bed light kit OFF. A single ‘beep’ will confirm reception of the command. 64 OPERATING INSTRUCTIONS Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 65: Adjustment

    Low - High Low - High Manifold Pressure 1.1” - 3.8” WC 2.9” - 11” WC Tap (B) (0.27 - 0.95 kPa) (0.72 - 2.74 kPa) #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces ADJUSTMENT 65...
  • Page 66: Burner Flame Adjustments

    Venturi settings(s) closed too far. Open venturi(s) slightly OR gas pressure too high - check manometer settings Figure 11.2, Burner Venturis Figure 11.3, Flame Appearance and Characteristics 66 ADJUSTMENT Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 67 (127mm) exhaust pipe. Make necessary modifications to achieve desired flame appearance. Insert restrictor plate into the 5” (127mm) exhaust pipe with the tabs pointing towards you. Reinstall all components previously removed. #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces ADJUSTMENT 67...
  • Page 68: Troubleshooting

    Remote control not working Replace batteries. properly No call for heat Verify remote control is powered ON and thermostat operation is turned OFF. 68 TROUBLESHOOTING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 69 A maximum number of failed Reset IFC module. Refer to Section 10.7 IFC Module Ignition Sequence ignitions or flame restorations has on page 60. been reached #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces TROUBLESHOOTING 69...
  • Page 70: Maintenance

    Performed by: Qualified Service Person Frequency: Annually Action: • Examination of the vent system is required. • The flow of combustion and ventilation air must not be obstructed. Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020 MAINTENANCE...
  • Page 71: Burner And Pilot System

    Figure 13.2, Pilot and Burner Correct Flame Appearance safety system. It must de-energize the safety shutoff in no more than (30) seconds. Burner Ports Burner ori ce Figure 13.1, Burner System #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces MAINTENANCE...
  • Page 72: Replacement Parts List

    BH44-005 SAFETY BARRIERS Safety Barrier Screen (only) BH44-ES Hussong Manufacturing Co., Inc. P.O. Box 577 204 Industrial Park Drive Lakefield, MN 56150-0577, USA BHM-44 72 REPLACEMENT PARTS LIST Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BHM-44 R.1 August 2020...
  • Page 73 BLACK GLASS PANEL SET Black Glass Panel Set BH44-BG900 Hussong Manufacturing Co., Inc. P.O. Box 577 204 Industrial Park Drive Lakefield, MN 56150-0577, USA BHM-44 #BHM-44 R.1 August 2020 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces REPLACEMENT PARTS LIST 73...
  • Page 74: Limited Lifetime Warranty

    • All parts and material except the items listed in the 30 day Kozy Heat gas appliance from the date of purchase to the original warranty and any exclusions or limitations that may apply. purchaser, that it is free of defects in materials and workmanship at *Hussong Mfg.

This manual is also suitable for:

Bhm-44

Table of Contents