Installation - Pioneer Premier DEH-P510UB Installation Manual

Conexión de las unidades Español
Cuando conecte altavoces sin utilizar el amplificador interno
• Cuando utilice este sistema, se recomienda apagar el amplificador interno de esta unidad.
Para los detalles, consulte el manual de instrucciones.
20 cm
Cable USB CD-U150E Pioneer
(vendido separadamente)
50 cm
Salida trasera
Este producto
Entrada remota por cable
iPod
Es posible conectar un adaptador
Salida delantera
de mando a distancia por cable
Salida de altavoz
(se vende por separado).
de subgraves
Toma de antena
Fusible (10 A)
Entrada IP-BUS (Azul)
Conector del Dock
Cable de interfaz Cable IP-BUS
Amarillo
Conecte el terminal de suministro de 12 V
constante.
Rojo
Conecte al terminal controlado por del
Amarillo/negro
interruptor de encendido (12 V CC).
Si se utiliza un equipo con función de
silenciamiento, conecte este conductor con el
Anaranjado/blanco
conductor de silenciamiento de audio en tal
Conecte al terminal de interruptor de iluminación.
equipo. De lo contrario, mantenga el
conductor de silenciamiento de audio libre de
conexiones.
Negro (masa de la carrocería)
Conecte a un punto de metal limpio, libre de
pintura.
Blanco Gris
No se usa.
Blanco/negro Gris/negro
Verde Violeta
Verde/negro Violeta/negro
Conexión de las unidades
Puerto USB 2
Utilice un cabo USB para conectar el dispositivo
de almacenamiento USB al puerto USB 2.
El cable USB CD-U150E Pioneer también está
disponible. Para los detalles, consulte
su revendedor.
Conecte los cables
A la salida
trasera RCA (vendidos
separadamente)
A la salida
delantera
A la salida del
altavoz de
Reproductor de
subgraves
Multi-CD (vendido
separadamente)
Control remoto de sistema
Azul/blanco
Conecte al terminal de control de sistema del
amplificador de potencia o al terminal de control de
relé de antena automática (máx. 300 mA 12 V CC).
Altavoz de
subgraves
Altavoz
delantero
Altavoz trasero
Español

Installation

Note
• Check all connections and systems before final
installation.
• Do not use unauthorized parts. The use of
unauthorized parts may cause malfunctions.
• Consult with your dealer if installation requires
drilling of holes or other modifications of the
vehicle.
• Do not install this unit where:
— it may interfere with operation of the vehicle.
Amplificador de
— it may cause injury to a passenger as a result of
potencia (vendido
a sudden stop.
separadamente)
• The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places
Amplificador de
such as near the heater outlet.
potencia (vendido
• Optimum performance is obtained when the unit
separadamente)
is installed at an angle of less than 60°.
Amplificador de
potencia (vendido
60°
separadamente)
DIN Front/Rear-mount
This unit can be properly installed either from
"Front" (conventional DIN Front-mount) or
"Rear" (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit
chassis). For details, refer to the following
installation methods.
DIN Front-mount
Installation with metal strap and
screws
1. Insert the mounting sleeve into the
dashboard.
• When installing in a shallow space, use a
supplied mounting sleeve. If there is enough
space behind the unit, use factory supplied
mounting sleeve.
Altavoz de
subgraves
Altavoz
delantero
Altavoz trasero
English Installation
2. Secure the mounting sleeve by 2. Insert the supplied extraction keys
using a screwdriver to bend the into both sides of the unit until
metal tabs (90°) into place. they click into place.
Mounting sleeve
Dashboard
182
53
3. Install the unit.
• Use commercially available parts when
installing.
Nut
Firewall or
3. Pull the unit out of the dashboard.
metal support
DIN Rear-mount
Metal strap
Screw
1. Extend top and bottom of the trim
ring outwards to remove the trim
ring. When reattaching the trim ring,
push the trim ring onto the unit until
Screw (M4 8)
it clicks. (If the trim ring is attached
upside down, the trim ring will not
fit properly.)
• It becomes easy to remove the trim ring if the
front panel is released.
• Make sure that the unit is installed securely
in place. Unstable installation may cause this
unit to malfunction, such as sound skip.
Removing the Unit
1. Extend top and bottom of the trim
ring outwards to remove the trim
ring. When reattaching the trim ring,
push the trim ring onto the unit until
2. Determine the appropriate position
it clicks. (If the trim ring is attached
where the holes on the bracket and
upside down, the trim ring will not
the side of the unit match.
fit properly.)
• It becomes easy to remove the trim ring if the
front panel is released.
Trim ring
English
3. Tighten two screws on each side.
• Use either truss screws (5 mm × 8 mm)
or flush surface screws (5 mm × 9 mm),
depending on the shape of screw holes in the
bracket.
Screw
Dashboard or Console
Factory radio mounting bracket
Fastening the front panel
If you do not plan to detach the front panel,
the front panel can be fastened with supplied
screw.
Screw
Trim ring