HERKULES BS 200 Original Operating Instructions page 18

Anleitung_BS_200_SPK7:_
GB
22. Have repairs carried out only by a qualified
electrician!
- This electric tool complies with the pertinent
safety regulations. Repairs are to be carried out
only by a qualified electrician using original
replacement parts or the user may suffer an
accident.
23. Wear safety gloves whenever you carry out any
maintenance work on the blade!
24. In the case of miter cuts when the table is tilted,
the guide must be positioned on the lower part of
the table.
25. When cutting round wood, use a device to stop
the workpiece from twisting.
26. When cutting boards in upright position, use a
device to prevent kick-back.
27. A dust extraction system designed for an air
velocity of 20 m/s should be connected in order
to comply with woodworking dust emission
values and to ensure reliable operation.
28. Give these safety regulations to all persons who
work on the machine.
29. Do not use this saw to cut fire wood.
30. The machine is equipped with a safety switch to
prevent it being switched on again accidentally
after a power failure.
31. Before you use the machine for the first time,
check that the voltage marked on the rating plate
is the same as your mains voltage.
32. If you use a cable reel, the complete cable has to
be pulled off the reel.
33. Persons working on the machine should not be
distracted.
34. Note the direction of rotation of the motor and
blade.
35. Never dismantle the machineʼs safety devices or
put them out of operation.
36. Never cut workpieces which are too small to hold
securely in your hand.
37. Never remove loose splinters, chips or jammed
pieces of wood when the saw blade is running.
38. It is imperative to observe the accident
prevention regulations in force in your area as
well as all other generally recognized rules of
safety.
39. Note the information published by your
professional associations.
40. Position the blade guard so it is approx. 3 mm
above the material you want to saw.
41. Important! Support long workpieces (e.g. with a
roller table) to prevent them sagging at the end
of a cut.
42. Make sure the blade guard (10) is in its lower
position when the saw is being transported.
43. Safety guards are not to be used to move or mis-
use the machine.
18
04.10.2010 10:02 Uhr Seite 18
44. Blades that are misshapen or damaged in any
way must not be used.
45. If the table insert is worn, replace it.
46. Never operate the machine if either the door
protecting the blade or the detachable safety
device are open.
47. Ensure that the choice of blade and the selected
speed are suitable for the material to be cut.
48. Do not begin cleaning the blade until it has come
to a complete standstill.
49. In the case of straight sawing against the parallel
stop, a push stick must be used.
50. The bandsaw blade guard should be in its lowest
position close to the bench during transport.
51. For miter cuts when the table is tilted, the parallel
stop must be positioned on the lower part of the
table.
52. When cutting round timber, use a suitable
holding device to prevent the workpiece turning.
53. Never use guards to lift or transport items.
54. Ensure that the bandsaw blade guards are used
and correctly adjusted.
55. Keep your hands a safety distance away from the
bandsaw blade. Use a push stick for narrow cuts.
5. Technical data
Voltage:
Power:
Ideal speed no:
Blade length:
Max. blade width:
Blade speed:
Cutting height:
Throat:
Table size:
Tilting range of table:
Workpiece size:
Weight:
230V ~ 50 Hz
S1 180 W S2 15 min. 250 W
1400 min -1
1400 mm
8 mm
900 m/min
80 mm / 90°
45 mm / 45°
200 mm
300 x 300 mm
0° to 45°
400 x 400 mm
18.5 kg