POSIFLEX KS-6115 User Manual
POSIFLEX KS-6115 User Manual

POSIFLEX KS-6115 User Manual

Fan free touch terminal w/ slim base
Hide thumbs Also See for KS-6115:

Advertisement

Quick Links

KS – 6115 / KS – 6115 UPS
Fan Free Touch Terminal
w/ Slim Base
User's Manual
Rev. A1
FCC Notes:
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.
Warranty Limits:
Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.
About This Manual:
Posiflex Technologies, Inc. has made every effort for the accuracy of the content in this
manual. However, Posiflex Technologies, Inc. will assume no liability for any technical
inaccuracies or editorial or other errors or omissions contained herein, nor for direct,
indirect, incidental, consequential or otherwise damages, including without limitation
loss of data or profits, resulting from furnishing, performance, or use of this material.
This information is provided "as is" and Posiflex Technologies, Inc. expressly
disclaims any warranties, expressed, implied or statutory, including without limitation
implied warranties of merchantability or fitness for particular purpose, good title and
against infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex Technologies, Inc. reserves the
right to alter product designs, layouts or drivers without notification. The system
integrator shall provide applicative notices and arrangement for special options utilizing
this product. The user may find the most up to date information of the hardware from:
http://www.posiflex.com or http://www.posiflex.com.tw or http://www.posiflexusa.com
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex Technologies, Inc. will not be responsible for any loss of data
resulting from the use, disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Technologies, Inc. the publisher of this documentation.
© Copyright Posiflex Technologies, Inc. 2007
All brand and product names and trademarks are the property of their respective holders.
Part 1
P/N: 16520901030

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KS-6115 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for POSIFLEX KS-6115

  • Page 1 About This Manual: Posiflex Technologies, Inc. has made every effort for the accuracy of the content in this manual. However, Posiflex Technologies, Inc. will assume no liability for any technical inaccuracies or editorial or other errors or omissions contained herein, nor for direct, indirect, incidental, consequential or otherwise damages, including without limitation loss of data or profits, resulting from furnishing, performance, or use of this material.
  • Page 2 ALERT TO OUR HONORABLE CUSTOMERS: l Please always read thoroughly all the instructions and documents delivered with the product before you do anything about it. Don’t take any premature action before you have a full understanding of the consequences. l This product contains inside a Lithium battery. Please always follow local environmental protection laws / regulations for disposal of used batteries and always replace only with battery of same type.
  • Page 3: Product Pictures

    INTRODUCTION PRODUCT PICTURES Front Views Side Views Rear View Bottom View (standard) (for 2.5” HDD in base) PARTS IDENTIFICATION 1. Main unit 2. Touch panel / LCD panel 3. Optional side mount kit e.g. SD-400 4. Power indicator / Logo 5.
  • Page 4: Product Features

    9. Lock / release button for main unit detach 10. Touch open cover 11. Power switch 12. Brightness adjust thumb wheel 13. Touch open door latch 14. PS/2 KB port 15. Rear connect cover 16. Cable exit 17. 2 cable exit 18.
  • Page 5 5. one proprietary USB port for optional side mount kit (e.g. SD-400) 6. one LAN port 10/100 base T Ethernet with LAN status indicators on jack (green for link, orange for data transmission), upgradeable to 1 Gbps 7. one external VGA monitor port 8.
  • Page 6: Opening Cable Cover

    INSTALLATION GUIDES CAUTION: Before any installation or cable connection to the set, please always make certain that the system is turned off and the external power source to the set is removed to prevent electric hazard! Never touch any metal pin in the connectors or circuits to avoid high voltage hazard or electrostatic discharge damage unless the operator is well grounded.
  • Page 7: Separating Main Unit

    SEPARATING MAIN UNIT In order to settle the touch terminal properly in a point of sale system, all the cable connections have to be routed through its base. Therefore, please observe the procedures from A to C below to separate the main unit from the slim base stand assembly after all cables in cable cover disconnected.
  • Page 8: Cable Passage

    4. Velcro Strap for UPS Battery (for KS-6115UPS) 5. Cable Passage To Main Unit For Desktop Mount Application 6. HDD Bracket Fixing Screw CABLE PASSAGE Please route all cables through the cable passage to main unit in desktop mount application. Hold them together with the cable tie. Pass all cables (but those for HDD and UPS battery for KS-6115UPS) through the cable exit to external connections.
  • Page 9: Routing The Cables

    12” 2 LCD Panel Or Customer Display Fit the joint base of PD-2501, PD-2602, PD-305, PD-306/U, PD-7622 or LM-6101 to the rear connect cover opening. Please route the interface cable through the normal cable exit (under the joint base) as in the 2 pictures.
  • Page 10: Side Mount Upgrade Kit

    Please note that only those qualified technicians may adjust in this window with information from Posiflex and the contents in the service window may change without notice as time develops. Jumpers Service Window...
  • Page 11: Wall Mounting

    Consequently, the mass storage device for KS-6115 series in wall mount application has to be either the CF card or the 2.5” HDD in main unit unless the type of wall mount kit is checked and found to fit the usage.
  • Page 12: Operating System Recovery

    CF Card no longer bootable. For KS systems preloaded with Windows XP Pro or WEPOS on HDD, Posiflex provides recovery CD or DVD delivered with the touch terminal for the preloaded operating system. The System Integrator shall take care of software restoration after OS recovered.
  • Page 13: Application Environment

    USING THE TOUCH TERMINAL APPLICATION ENVIRONMENT It is very important that you check the following operational guidelines: Ventilation This terminal must NOT be operated in an environment with restricted ventilation. There must be at least 25 mm air clearance around any top or side ventilation holes with a free flow of air around the unit at ALL times for the installation.
  • Page 14: Power On/Off

    Emergency treatment: The battery is constructed maintenance free and leakproof. It is well protected in KS system as long as the ambient temperature remains below 30°C and the ventilation of the KS system remains free. However, should any accident happen and the sulfuric acid from the battery spills on skin or clothing, wash immediately with water.
  • Page 15 In preloaded Windows, “Posiflex Power Switch Manager” in “Posiflex Tools” in the Program Files helps managing these functions. Software Support Features The KS series provides a software power off command for application program maneuvers for KS-6115UPS.
  • Page 16: Display Issues

    DC adaptor to connect into the monitor (for TM-4115 / TM-7112) or its VGA cable (for LM-6112) or use Posiflex VGA + power cable and set an internal jumper in KS main unit to supply the required power through the VGA connector (for LM-6101).
  • Page 17: Touch Panel

    before “G” or already standard RS232 serial ports without conversion cables for system revision since “G” as status at delivery. When a serial Modem is to be used in KS system, it is most recommended to use COM2 port for this purpose. In this way any hardware resource conflict is eliminated.
  • Page 18 Posiflex Touch Terminal Manager A program named “Posiflex Touch Terminal Manager” and a right- click sticky button tool in the program group “Posiflex Tools” is installed in the preloaded Windows system with a PS/2 interface touch panel controller. This program can also be obtained by download from the POSIFLEX web site.
  • Page 19 Part 19...
  • Page 20 T31454 警告使用者 這是甲類的資訊產品,在居住的環 境 中 使 用 時 , 可 能 會 造 成 射 頻 干 擾,在這種情況下,使用者會被要 求採取某些適當的對策。 Part 20...

This manual is also suitable for:

Ks-6115 ups

Table of Contents