I [Event] Function For Events - Panasonic WJ-HD309 Operating Instructions Manual

I [Event] Function for Events

Perform the settings for event actions of each event type
(motion detection, video loss, command alarm and terminal
alarm).
SETUP MENU
Event Setup
VMD Setup
Alarm Setup
Terminal Setup
G [Event Setup] Settings for the alarm output
duration and the buzzer duration
Perform the settings for the alarm output duration and the
buzzer sound duration for each event type (motion detec-
tion, video loss, command alarm and terminal alarm).
SETUP MENU
Event Setup
VMD Setup
Alarm Setup
Terminal Setup
SETUP MENU
Event Setup
VMD Setup
Alarm Setup
Terminal Setup
The following are available for the alarm output duration.
When OFF is selected, the alarm output will not be sup-
plied.
(s: second, m: minute)
OFF: No alarm output is supplied.
1 s - 30 s (in 1 second intervals)
/40 s/50 s/1 m/2 m/3 m/4 m/5 m
EXT: Alarm output will continue until the ALARM RESET
button is pressed.
Important:
The alarm output duration cannot be set for video loss.
Signals will be supplied continuously from the camera
error output terminal (pin no. 17) of the ALARM/CON-
TROL connector on the rear panel during the period
when the video signal is lost. (Refer to page 83.)
100
Maintenance Recording Event Schedule
LIVE
Switcher Display Comm System
I
VMD
SETUP
I
Video Loss
SETUP
I
Terminal/Command Alarm
SETUP
Maintenance Recording Event Schedule
LIVE
Switcher Display Comm System
I
VMD SETUP
I
Video Loss
SETUP
I
Terminal/Command Alarm
SETUP
Maintenance Recording Event Schedule
LIVE
Switcher Display Comm System
I
VMD
SETUP
I
Video Loss Setup
SETUP
I
Terminal/Command Alarm Setup
SETUP
I
Alarm Output
1 0 s
I
Buzzer
1 0 s
O K CANCEL
The following are available for the buzzer sound duration.
When OFF is selected, a buzzer will not sound.
(s: second, m: minute)
OFF: The buzzer will not sound.
1 s - 30 s (in 1 second intervals)
/40 s/50 s/1 m/2 m/3 m/4 m/5 m
EXT: The buzzer will continue until the ALARM RESET but-
ton is pressed.
G [VMD Setup] Perform the settings for the
motion detection function
Select ON or OFF to determine whether to enable or dis-
able the motion detection function for each camera chan-
nel.
When ON is selected, perform the settings for the motion
detection area for each camera channel. Up to 4 areas can
be set for a camera channel for the detection area. Refer to
page 45 for further information about the motion detection
function.
SETUP MENU
Maintenance Recording
Switcher Display
I
CAM1
Event Setup
I
CAM2
VMD Setup
I
CAM3
I
Alarm Setup CAM4
I
CAM5
Terminal Setup
I
CAM6
I
CAM7
I
CAM8
I
CAM9
I
CAM10
I
CAM11
I
CAM12
I
CAM13
I
CAM14
I
CAM15
I
CAM16
[Screenshot 1]
Start operation from the camera channel selection menu of
the "VMD Setup" window.
SETUP MENU
Maintenance Recording
Switcher Display
I
CAM1
Event Setup
I
CAM2
VMD Setup
I
CAM3
I
Alarm Setup CAM4
I
CAM5
Terminal Setup
I
CAM6
I
CAM7
I
CAM8
I
CAM9
I
CAM10
I
CAM11
I
CAM12
I
CAM13
I
CAM14
I
CAM15
I
CAM16
z Rotate the jog dial to select ON for a desired camera
channel for which the motion detection function is to be
applied, and press the SET button.
Event Schedule
LIVE
Comm System
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Event Schedule
LIVE
Comm System
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF