4. Do not use strong or abrasive detergents
objects. Otherwise, blooming or smear may
when cleaning the camera body.
be caused.
Use a dry cloth to clean the camera when it is
7. Do not operate the camera beyond its
dirty.
specified temperature, humidity or power
In case the dirt is hard to remove, use a mild
detergent and wipe gently. Afterwards, wipe
source ratings.
off the remained part of the detergent in it
Use the camera under conditions where tem-
with a dry cloth.
perature is between –10 °C - +50 °C {14 °F -
122 °F}, and humidity is below 90 %.
5. Clean the CCD faceplate with care.
The input power source is 120 V AC 60 Hz for
Do not clean the CCD with strong or abrasive
WV-CP240EX, 12 V DC for WV-CP242EX, and
detergents. Use lens tissue or a cotton tipped
24 V AC 60 Hz for WV-CP244EX.
applicator and ethanol.
Caution:
6. Never face the camera towards the sun.
To prevent fire or electric shock hazard, use
Do not aim the camera at bright objects.
a UL listed cable (VW-1, style 1007) for the
Whether the camera is in use or not, never
DC 12 V or AC 24 V Input Terminal.
aim it at the sun or other extremely bright
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
<WV-CP240EX>
ALC
BLC ON
ALC
BLC ON
VIDEO
SHARP
INT
VIDEO
SHARP
INT
LOCK
VIDEO OUT
DC
SOFT
LL
ELC
OFF
<WV-CP244EX>
SOFT
LL
DC
OFF
ELC
AC 24V IN
GND
1
2
ALC
BLC ON
VIDEO
SHARP
INT
VIDEO OUT
LL
DC
SOFT
ELC
OFF
ALC
BLC ON
<WV-CP242EX>
VIDEO
SHARP
DC 12V IN
DC
SOFT
ELC
OFF
ALC
BLC ON
VIDEO
SHARP
VIDEO OUT
Mount Adapter
DC
SOFT
ELC
OFF
q ALC Lens Connector
ON: Select this mode when a strong light
such as a spotlight is in the background.
Supplies power and control signals to an auto
OFF: Normal picture.
iris lens (not supplied).
!1 Detail/Aperture Level Selector [SHARP,
w Flange-back Adjusting Ring
SOFT]
This ring adjusts the back-focal distance or
The detail/aperture level can be selected with
picture focus. Rotate this ring clockwise for a
this selector. Set it to the desired position
C-mount lens or counterclockwise for a CS-
while observing the picture on the monitor.
mount lens.
SHARP: Normal position.
e Lens (option)
SOFT: Select this position when a Quad
System is connected to this camera.
r Mount Adapter
!2 Automatic Light Control/Electronic Light
The camera mounting screw hole is for
Control Selector [ALC, ELC]
mounting the camera onto a mounting brack-
Lets you select the mode according to the
et. The camera is originally designed to be
lens type used.
mounted from the bottom, however, a top-
ALC: Select this mode when an auto iris lens
mounting type is also available. To mount
(ALC lens) is used with this camera.
from the top, remove the mount adapter from
ELC: Select this mode when a fixed iris lens
the bottom of the camera by removing two
or manual iris lens is used with this cam-
fixing screws. Attach the mount adapter to
era.
the top as shown in the diagram, then mount
the camera on the mounting bracket. Make
!3 Lens Drive Signal Selector [VIDEO, DC]
sure that two original screws are used when
Lets you select the mode according to the
mounting the mount adapter; longer type
type of auto iris lens drive signal to be sup-
screws may damage inner components, too
plied to the lens from the auto iris lens con-
shorter type screws may cause the camera
nector.
drop.
VIDEO: Select this mode if you are using a
t Focus Fixing Screw
auto iris lens that requires a video drive
signal.
y Power Cord (only for WV-CP240EX)
DC: Select this mode if you are using a auto
iris lens that requires a DC drive signal.
Connect this power cord to an electrical out-
let of 120 V AC 60 Hz.
!4 Video Output Connector [VIDEO OUT]
u DC 12 V Input Terminal
This connector is for connecting with the
VIDEO IN connector of the video monitor.
[DC 12V IN] (only for WV-CP242EX)
Whenever the multiplexed vertical drive (VD2)
This terminal is for connecting the 12 V DC
signal is supplied to this connector, the cam-
power supply cord.
era synchronization mode is automatically set
i AC 24 V Input Terminal
to Vertical Drive.
[AC 24V IN] (only for WV-CP244EX)
This terminal is for connecting the 24 V AC
60Hz power supply cord.
Cautions:
• Connect to 12 V DC (10.5 V-16 V) or 24 V
o Synchronization Mode Selector
AC (19.5 V-28 V) class 2 power supply
[INT, LL] (only for WV-CP240EX and WV-
only. Make sure to connect the grounding
CP244EX)
lead to the GND terminal when the power
Selects the camera synchronization mode as
is supplied from a 24 V AC power source.
either internal sync mode (INT) or line-lock
• To prevent fire or electric shock hazard,
mode (LL).
use a UL listed cable (VW-1, style 1007)
INT: Sets to internal 2:1 interlace.
for the DC 12 V or AC 24 V Input
LL: Sets to Line-lock mode.
Terminal.
!0 Back Light Compensation Mode Selector
[BLC ON, OFF]
Lets you select the mode according to the
position of the object and light conditions on
the screen.