Unverferth BLU-JET Legacy NH3 Manual
  1. Manuals
  2. Brands
  3. Unverferth Manuals
  4. Farm Equipment
  5. BLU-JET Legacy NH3
  6. Manual

Unverferth BLU-JET Legacy NH3 Manual

Applicator
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
NH3 Applicator
Legacy
Beginning with Serial Number A66360100
Part No. J0605010

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BLU-JET Legacy NH3 and is the answer not in the manual?

Questions and answers

Related Manuals for Unverferth BLU-JET Legacy NH3

Summary of Contents for Unverferth BLU-JET Legacy NH3

  • Page 1 NH3 Applicator Legacy Beginning with Serial Number A66360100 Part No. J0605010...
  • Page 2 The information, specifications, and illustrations in the manual are based on the information avail- able at the time it was written. Due to continuing improvements in the design and manufacture of Unverferth products, all specifications and information contained herein are subject to change without notice.
  • Page 3 — Introduction Legacy Product Information When ordering parts or when requesting further information or assistance, always give the following information: • Machine name • Model • Serial number All products manufactured by Blu-Jet are warranted to be free from material and workmanship defects for one full year from time of consumer delivery.

  • Page 4: Table Of Contents

    — Introduction Legacy TABLE OF CONTENTS Foreword ............................... 2 Pre-Operation Checklist ..........................2 SECTION I Safety General Hazard Information ........................1-2 Safety Decals .............................1-3 Following Safety Instructions ........................1-6 Before Servicing ............................1-6 Before Operating ............................1-7 During Operation ............................1-7 Before Transporting ............................1-8 During Transport ............................1-8 Pressurized Oil ............................1-9 Chemical Hazzards ...........................1-10 Preparing for Emergencies ........................1-10...
  • Page 5 — Introduction Legacy TABLE OF CONTENTS SECTION III Operation Preparing Tractor ............................3-2 Preparing Applicator ...........................3-2 Hardware .............................3-2 Pivot Pins ............................3-2 Hitch ..............................3-2 Hydraulic System ..........................3-2 Tires/Wheels ............................3-3 Lubrication ............................3-3 Hitching to the Tractor ..........................3-4 Drawbar Hitching ..........................3-4 Transport Chain ..........................3-5 Hydraulic Connections .........................3-6 Electrical Connection ..........................3-6 Jack Usage ..............................3-7...
  • Page 6 — Introduction Legacy TABLE OF CONTENTS SECTION IV Maintenance Lubrication ..............................4-2 Legacy Maintenance ..........................4-4 Seasonal Storage ..........................4-4 Purging A Hydraulic System .......................4-5 Schematics ..............................4-6 Wheel, Hub and Spindle Disassembly and Assembly ................4-8 Wheels and Tires .............................4-10 Wheel Nut Torque Requirements ......................4-10 Tire Pressure ............................4-11 Tire Warranty ............................4-11 Complete Torque Chart ..........................4-12...
  • Page 7 — Introduction Legacy TABLE OF CONTENTS SECTION V Parts Clean Water Tank Components .........................5-2 Hitch, Transport Chain, Manual Holder and Jack ..................5-4 Depth Control Components ........................5-6 Main Frame Components ...........................5-8 Primary Wing Components ........................5-10 Secondary 5’8” Wing Components ......................5-12 Secondary 3’2” Wing Components ......................5-14 Secondary Wing Extension to 50 Ft.
  • Page 8 — Introduction Legacy TABLE OF CONTENTS SECTION V Parts (continued) SuperShooter III Connection Single 1.25” Plumbing ................5-68 SuperShooter III Connection Double 1.25” Plumbing ................5-70 SuperShooter III Components - 1.25” Connection ................5-72 SuperShooter III Single 1 1/4” Assembly ....................5-74 SuperShooter III Max Single 1 1/2” Assembly ..................5-75 SuperShooter III Connection Single 1.5”...

  • Page 9: Section I

    — Safety Legacy SECTION I Safety General Hazard Information ........................1-2 Safety Decals .............................1-3 Following Safety Instructions ........................1-6 Before Servicing ............................1-6 Before Operating ............................1-7 During Operation ............................1-7 Before Transporting ............................1-8 During Transport ............................1-8 Pressurized Oil ............................1-9 Chemical Hazzards .............................1-9 Anhydrous Ammonia (NH3) ........................1-10 Clean Water Tank ............................1-11 Preparing for Emergencies ........................1-11 Wearing Protective Equipment .........................1-11...

  • Page 10: Safety

    It is true that the designer, the manufacturer, and the safety engineer can help; and they will help, but their combined efforts can be wiped out by a single careless act of the operator. It is said that, “the best kind of a safety device is a careful operator.” We, at Unverferth Mfg.

  • Page 11: Safety Decals

    — Safety Legacy Safety Decals • Replace lost, damaged, painted, oR unReadable decals immediately. if paRts that have decals aRe Replaced, also make suRe to install new DECALS. THESE DECALS INFORM AND REMIND THE OPERATOR WITH OPERATIONAL INFORMATION AND SAFETY MESSAGES. 9501197 97048 97961...
  • Page 12 — Safety Legacy Safety Decals (continued) 97337 9003125 - Fluorescent Strip 9003126 - Reflector RED 9003127 - Reflector AMBER (Continued)
  • Page 13 — Safety Legacy Safety Decals (continued) JAP2227 JAP2973 9503899 - 1 1/4” Connection 9503900 - 1 1/2” Connection JAP2974...

  • Page 14: Following Safety Instructions

    — Safety Legacy Following Safety Instructions • Read and understand this operator’s manual before operating. • All machinery should be operated only by trained and authorized personnel. • To prevent machine damage, use only attachments and service parts approved by the manufacturer.

  • Page 15: Before Operating

    — Safety Legacy Before Operating • Do not stand between towing vehicle and implement during hitching. • Always make certain everyone and everything is clear of the machine before beginning operation. • Verify that all safety shields are in place and properly secured. •...

  • Page 16: Before Transporting

    — Safety Legacy Before Transporting • Secure transport chains to towing vehicle before transporting. DO NOT transport without chains. • Install transport locks before transporting. • Check for proper function of all available transport lights. Make sure that all reflectors are clean and in place on machine.

  • Page 17: Pressurized Oil

    — Safety Legacy Pressurized Oil • Relieve pressure before disconnecting hydraulic lines, loosening any hydraulic fittings or servicing hydraulic system. See the maintenance section of this manual for the procedure to relieve pressure. • High-pressure fluids can penetrate the skin and cause serious injury or death.

  • Page 18: Anhydrous Ammonia (Nh3)

    — Safety Legacy Anhydrous Ammonia (NH3) • Exposure to anhydrous ammonia (NH3) will cause serious injury or death. Anhydrous ammonia causes severe burns to the eyes, skin, and respiratory system. Immediately flush exposed areas with fresh water and seek medical treatment. •...

  • Page 19: Preparing For Emergencies

    — Safety Legacy Clean Water Tank • A clean water tank is provided as standard equipment. It is equipped with a spigot for general washing and a hose for emergency eye washing. • Always keep clean water in tank. Water in clean water tank is not suitable for human consumption.
  • Page 20 — Safety Legacy Notes 1-12...

  • Page 21: Set Up

    — Set Up Legacy SECTION II Set Up Set Up ...............................2-2 Tongue Assembly to Main Frame Assembly .....................2-3 Attaching Depth Stop and Routing Hoses ....................2-5 Nurse Tank Hitch Assembly ........................2-6 Transport Lighting Assembly ........................2-7 SMV Assembly ............................2-9 Mounting Offset Stagger & Double Extension Brackets .................2-10 Sealer II Assembly (JAAM2857) - Optional Sealer II Spring Add-On Kit ..........2-11 Torsion Arm Assembly ..........................2-12 Attaching Bearings and Basket to Mounting Arms .................2-12...

  • Page 22: Set Up

    — Set Up Legacy Set Up • Read and undeRstand safety Rules befoRe opeRating oR seRvicing this machine. Review the safety section in this manual if necessaRy. • tipping oR movement of the machine can cause seRious injuRy oR death. be suRe the machine is secuRely blocked.

  • Page 23: Tongue Assembly To Main Frame Assembly

    — Set Up Legacy Tongue Assembly to Main Frame Assembly 1. Using a safe lifting device rated for at least 2,000 lbs., secure tongue assembly to main frame with 2” Dia. x 10 1/4” pins (JBM3565), 5/8”-11UNC x 4” capscrews (9390-132), and 5/8”-11UNC elastic lock nuts (9398-019).
  • Page 24 — Set Up Legacy Tongue Assembly to Main Frame Assembly (continued) 2. Rotate tongue cylinder linkage (JAM6183) to the tongue cylinder arm linkage (JAM6182). Secure with 1 1/4” Dia. x 7 3/4” pin (JBM3465), 3/8”-16UNC x 2 1/2” capscrew (9390-061) and 3/8”-16UNC lock nut (902875) (FIG. 2-2). fig.

  • Page 25: Attaching Depth Stop And Routing Hoses

    — Set Up Legacy Attaching Depth Stop and Routing Hoses 1. Bolt the depth stop to the main frame. (FIG. 2-4) fig. 2-4 secure 2. Route hoses along the right side of the fig. 2-5 tongue. (FIG. 2-5)

  • Page 26: Nurse Tank Hitch Assembly

    — Set Up Legacy Nurse Tank Hitch Assembly 1. Using a safe lifting device rated at a miminum of 1000 lbs., attach the nurse tank hitch assembly to the main frame with twelve 3/4”-10UNC x 2 1/2” capscrews (9390-147) and 3/4”-10UNC lock nuts (97025).

  • Page 27: Transport Lighting Assembly

    See federal regulation 49 CFR 562; available at www.govinfo.gov for US federal law requirements. See your Unverferth dealer for additional brackets, reflectors, or lights to meet your requirements. NOTE: Consult row spacing layout for light kit placement.
  • Page 28 — Set Up Legacy Light Kit Assembly and Mounting Transport Lighting Assembly (continued) 1. Rear electrical wiring harness (JAP3222) is extended down the right-hand side of the tongue through hose holders to dust cap. 2. Attach electrical wiring harness extension (JAP3222) to electrical plug and socket harness (JAP3223).

  • Page 29: Smv Assembly

    — Set Up Legacy Light Kit Assembly and Mounting SMV Assembly 1. Mount SMV mounting bracket (JAM3420) near the center of the rear bar with 3/8”-16UNC x 5” x 6 7/16” U-bolt (JBP3045) and 3/8”-16UNC elastic lock nuts (9398-012). (FIG. 2-23) 2.

  • Page 30: Mounting Offset Stagger & Double Extension Brackets

    — Set Up Legacy Mounting Offset Stagger & Double Extension Brackets NOTE: For proper positioning, refer to “Overhead Layouts”, in SET UP section. 1. Using a safe lifting device rated for at least 100 lbs., attach 6” x 6” mounting offset stagger brackets (JAM4545BB) with 3/4”-10UNC x 6”W x 7 1/16”L U-bolts (JBP3350), and 3/4”-10UNC lock nuts (9802).

  • Page 31: Sealer Ii Assembly (Jaam2857) - Optional Sealer Ii Spring Add-On Kit

    — Set Up Legacy Sealer II Assembly (JAAM2857) Optional Sealer II Spring Add-On Kit 1 Row 1. Remove the 1/2”-13UNC x 1 1/2” capscrews 9404-025 (9390-101), 1/2” lock washer (9404-025) and 9394-010 9390-101 1/2”-13UNC hex nut (9394-010) from the lower clevis (JAM2489) (FIG. 2-32). 9390-109 94981 2.

  • Page 32: Torsion Arm Assembly

    — Set Up Legacy Torsion Arm Assembly Attaching Bearings and Basket to Mounting Arms 1. Loosely attach bearing (JAP2144) on strip-till fig. 2-39 basket mount arm (JAM2269), with 7/16”- 14UNC x 1 1/2” capscrews (9390-080), 7/16” lock washers (9404-023), and 7/16”-14UNC JAM2269 hex nuts (9394-008).

  • Page 33: Center Basket

    — Set Up Legacy Torsion Arm Assembly (continued) Center Basket 1. Position StripTill basket assembly on torsion spring assembly (FIG. 2-42). Insert 1/2”- fig. 2-42 JAM7568 13UNC x 1 1/2” capscrews (9390-101), top and bottom. Secure top pivot hex cap 9390-101 94981 screws with 1/2”...

  • Page 34: Attaching Torsion Arm Assembly To 6"X6" Tube (Jaam2630)

    — Set Up Legacy Torsion Arm Assembly (continued) Attaching Torsion Arm Assembly To 6”x6” Tube (Bundle #JAAM2630) 1. Center and attach torsion arm assembly fRont mount 6”x6” tube (J70210641), to the basket mount plate (JAM7637) with 5/8”-11UNC x 2 1/2”W x 4”L Parts List 9394-014 U-bolts (JBP3300), 5/8”...

  • Page 35: Maxpac Ar700 Assembly

    — Set Up Legacy MaxPac AR700 Assembly 1. Using a safe lifting device rated at a minimum of 150 lbs., secure MaxPac row unit (JAM2264) with 1 1/4” x 2” EdgeBent shank (JAP2125) with backing plate (JAM2262), 3/4”-10UNC x 8” capscrews (9390-161) 3/4” lock washers (9404-033), and 3/4”-10UNC hex nuts (9394-016).

  • Page 36: Residue Manager Assembly

    — Set Up Legacy Residue Manager Assembly Refer to Residue Manager manual #J0400023 for specific Set Up instructions. fig. 2-53 2-16...

  • Page 37: Legacy 38' And 42' Toolbars

    — Set Up Legacy Legacy 38’ and 42’, Toolbars Legacy 38’ Legacy 42’ Legacy SD 42’ 2-17...

  • Page 38: Legacy 47' And 52' Toolbars

    — Set Up Legacy Legacy 47’ and 52’, Toolbars Legacy 47’ Legacy 52’ 2-18...
  • Page 39 — Set Up Legacy Overhead Layout - Legacy - 12 Row 30” Spacing 164-1/4" 105" 60" BLU-JET Legacy 14-1/2" 12 Row 30" Spacing SCS row units SealPro II sealers AM4545 JAM4545BB 22" X 20" 22” x 20” 45" AM6160 & JAM6160BB AM6161 &...
  • Page 40 — Set Up Legacy Overhead Layout - Legacy - 13 Row 30” Spacing 180" 165" BLU-JET Legacy 120" 90" 13 Row 30" Spacing 57" 37" SCS row units 30" AM4510 JAM4510BB 22" X 8" SealPro II sealers 22” x 8” AM4545 JAM4545BB 22"...
  • Page 41 — Set Up Legacy Overhead Layout - Legacy - 13 Row 30” Spacing 180" 165" BLU-JET Legacy 120" 90" 13 Row 30" Spacing 57" 37" AM4510 MaxPac row units JAM4510BB 22" X 8" 30" 22” x 8” SealPro II sealers AM4545 JAM4545BB 22"...
  • Page 42 — Set Up Legacy Overhead Layout - Legacy - 15 Row 30” Spacing 2-22...
  • Page 43 — Set Up Legacy Row Spacing Overhead Layout - Legacy - 16 Row 30” Spacing BLU-JET LEGACY 16 ROW 30” SPACING Maxpac Row Units SealPro Il Sealers Residue Managers Firming Baskets 2-23...
  • Page 44 — Set Up Legacy Overhead Layout - Legacy - 16 Row 30” Spacing BLU-JET LEGACY 16 ROW 30” SPACING SCS Row Units SealPro Il Sealers 2-24...
  • Page 45 — Set Up Legacy Overhead Layout - Legacy - 17 Row 30” Spacing BLU-JET LEGACY 17 ROW 30” SPACING SCS Row Units SealPro Il Sealers 2-25...
  • Page 46 — Set Up Legacy Overhead Layout - Legacy - 18 Row 20” Spacing BLU-JET LEGACY 18 ROW 20” SPACING SCS Row Units SealPro II Sealer 2-26...
  • Page 47 — Set Up Legacy Overhead Layout - Legacy - 18 Row 30” Spacing BLU-JET LEGACY 18 ROW 30” SPACING SCS Row Units SealPro Il Sealers 2-27...
  • Page 48 — Set Up Legacy Overhead Layout - Legacy - 18 Row 30” Spacing BLU-JET LEGACY 18 ROW 30” SPACING MACPAC Row Units SealPro Il Sealers 2-28...
  • Page 49 — Set Up Legacy Overhead Layout - Legacy - 18 Row 30” Spacing BLU-JET LEGACY 18 ROW 30” SPACING Maxpac Row Units SealPro Il Sealers Residue Managers Firming Baskets 2-29...
  • Page 50 — Set Up Legacy Overhead Layout - Legacy - 19 Row 30” Spacing BLU-JET LEGACY 19 ROW 30” SPACING SCS Row Units SealPro Il Sealers 2-30...
  • Page 51 — Set Up Legacy Overhead Layout - Legacy - 21 Row 30” Spacing BLU-JET LEGACY 21 ROW 30” SPACING SCS Row Units SealPro Il Sealers 2-31...
  • Page 52 — Set Up Legacy Overhead Layout - Legacy - 24 Row 20” Spacing BLU-JET LEGACY 24 ROW 20” SPACING SCS Row Units SealPro Il Sealers 2-32...
  • Page 53 — Set Up Legacy Overhead Layout - Legacy Side Dresser - 13 Row 30” Spacing 180" 165" BLU-JET Legacy SD 120" 90" 13 Row 30" Spacing 57" 37" SCS row units 30" AM4510 JAM4510BB 22" X 8" SealPro II sealers 22”...
  • Page 54 — Set Up Legacy Overhead Layout - Legacy Side Dresser - 13 Row 30” Spacing 180" 165" 120" 90" AM4510 JAM4510BB 60" 22" X 8" 22” x 8” 47" 37" AM4509 JAM4509BB 33" X 20" 30" 33” x 20” AM4545 JAM4545BB 22"...
  • Page 55 — Set Up Legacy Overhead Layout - Legacy Side Dresser - 17 Row 30” Spacing BLU-JET LEGACY SD 17 ROW 30” SPACING MACPAC Row Units SealPro Il Sealers 2-35...
  • Page 56 — Set Up Legacy Overhead Layout - Legacy Side Dresser - 17 Row 30” Spacing BLU-JET LEGACY SD 17 ROW 30” SPACING SCS Row Units SealPro Il Sealers 2-36...
  • Page 57 — Set Up Legacy Overhead Layout - Legacy Side Dresser - 19 Row 30” Spacing BLU-JET LEGACY SD 19 ROW 30” SPACING MACPAC Row Units SealPro Il Sealers 2-37...
  • Page 58 — Set Up Legacy Overhead Layout - Legacy Side Dresser - 19 Row 30” Spacing BLU-JET LEGACY SD 19 ROW 30” SPACING SCS Row Units SealPro Il Sealers 2-38...

  • Page 59: Raven Rcm Guide

    — Set Up Legacy Raven RCM Guide RCM Set-Up Whenever the tractor is turned off or the ECU for the anhydrous applicator loses power, the following steps will have to be performed in order for the RCM to function properly right away. NOTE: Before programming the RCM, ensure the RCM monitor is connected to the battery.
  • Page 60 — Set Up Legacy Raven RCM Guide (continued) 7. Under Application Type, select “NH3” or “NH3 HP+” depending on cooler type. NOTE: “NH3 HP+” is only used with the Raven AccuFlow HP+ cooler equipped with a PWM boost pump. 8. Press the Next Page icon. 9.
  • Page 61 — Set Up Legacy Raven RCM Guide (continued) 11. Verify or enter the widths of the individual sections. NOTE: If section widths are unknown, simply count the number of rows plumbed into each section and multiply by the row width. Section 1 will start on the left hand side of the machine when facing the machine form the rear.
  • Page 62 — Set Up Legacy Raven RCM Guide (continued) 15. Review the information on the Section Summary screen. 16. If the information is correct, press the Next Page icon. To make adjustments to the configuration, press Back and adjust settings as needed. 17.
  • Page 63 — Set Up Legacy Raven RCM Guide (continued) 19. Select “0-250psi (1-5V)” for pressure sensor 1. If cooler is equipped with PWM Boost Pump, select “0-250psi (1-5V)” for pressure sensor 2 as well. 20. Press the Next Page icon. 21. Setup desired pressure alarms for each of the pressure sensors.
  • Page 64 — Set Up Legacy Raven RCM Guide (continued) 23. Select the control valve type, either “AccuFlow Dual Valve” or “AccuFlow Single Valve”. These correspond to the number of control valves at the cooler. 24. Enter the desired Valve Response Rate, Control Deadband, and Control Effort. If “AccuFlow Dual Valve”...
  • Page 65 — Set Up Legacy Raven RCM Guide (continued) 28. Enter the Tank Capacity, Current Tank Level, and Low Tank Level values. 29. If desired, select the Alarm? Checkbox to be notified when the tank fill level falls below the low tank level threshold. 30.
  • Page 66 — Set Up Legacy Raven RCM Guide (continued) 36. Enter 20 for Off Rate Alarm and check Alarm? box. NOTE: Alarm prompts when over 20% off target rate. 37. Make sure Section Valve Status Feedback Alarm is unchecked. 38. Press the Next Page icon. 39.
  • Page 67 — Set Up Legacy Raven RCM Guide (continued) Flow Meter Calibration Flow Meter Calibration can be accomplished using the Applied Product Calibration. This calibration should only be done if the applied lbs of N is varying greatly from actual applied lbs of N.
  • Page 68 — Set Up Legacy Raven RCM Guide (continued) 4. Read the calibration directions carefully. Touch the blue checkmark. 5. Touch Stop Accumulating when complete. 6. Follow on screen steps to finish calibration. 2-48...
  • Page 69 — Set Up Legacy Raven RCM Guide (continued) Energize System An energize system test allows the operator to pressurize the system after connecting to a new nurse tank or re-energizing the system to begin a job. 1. Navigate to the Diagnostics page and select the Tests tab.
  • Page 70 — Set Up Legacy Raven RCM Guide (continued) 3. Press begin to start the process. A warning alarm will pop up saying that the test will discharge anhydrous ammonia. Make sure to read the warning carefully. Touch the green checkmark. 4.
  • Page 71 — Set Up Legacy Raven RCM Guide (continued) Bleed System Test A Bleed System Test allows the operator to bleed the system after the nurse tanks have been disconnected. NOTE: The bleed system test will not evacuate all of the NH3 entirely. Perform the manual bleed procedure for the system to ensure NH3 is completely evacuated.
  • Page 72 — Set Up Legacy Raven RCM Guide (continued) 3. Press begin to start the process A warning alarm will pop up saying that the test will discharge anhydrous ammonia. Make sure to read the warning carefully. Touch the green checkmark. 4.
  • Page 73 — Operation Legacy SECTION III Operation Preparing Tractor ............................3-2 Preparing Applicator ...........................3-2 Hardware .............................3-2 Pivot Pins ............................3-2 Hitch ..............................3-2 Hydraulic System ..........................3-2 Tires/Wheels ............................3-3 Lubrication ............................3-3 Hitching to the Tractor ..........................3-4 Drawbar Hitching ..........................3-4 Transport Chain ..........................3-5 Hydraulic Connections .........................3-6 Electrical Connection ..........................3-6 Jack Usage ..............................3-7 Parked Position ...........................3-7...

  • Page 74: Preparing Tractor

    — Operation Legacy Preparing Tractor Before operating applicator, read the tractor operator’s manual and gain an understanding of its safe methods of operation. Check the tractor brakes and transport lights. Make sure they are in proper working order. Check the tractor hydraulic oil reservoir and add oil if needed. Verify that the tractor is adequately ballasted for drawbar operation at the anticipated draft and vertical tongue load.

  • Page 75: Tires/Wheels

    — Operation Legacy Preparing Applicator (continued) Tires/Wheels Check tire pressures and maintain at recommended values listed in the MAINTENANCE section. • IMPROPERLY TORQUED WHEEL NUTS/BOLTS CAN CAUSE A LOSS OF IMPLEMENT CONTROL AND MACHINE DAMAGE. WHEEL NUTS/BOLTS MUST BE CHECKED REGU- LARLY.

  • Page 76: Hitching To The Tractor

    — Operation Legacy Hitching to the Tractor Drawbar Hitching • DO NOT STAND BETWEEN THE IMPLEMENT AND TRACTOR WHEN HITCHING. ALWAYS ENGAGE PARKING BRAKE AND STOP ENGINE BEFORE INSERTING HITCH PIN. Connect the hitch to the tractor drawbar. Do not attempt to hitch to any other location on FIG.

  • Page 77: Transport Chain

    — Operation Legacy Hitching to the Tractor (continued) Transport Chain Always use a transport chain when connecting Transport chain connection shown for the implement directly to a tractor. Make sure illustration purposes only. Refer to the intermediate chain support is in use. tractor manufacturer for proper attachment.

  • Page 78: Hydraulic Connections

    — Operation Legacy Hitching to the Tractor (continued) Hydraulic Connections After cleaning hydraulic hose couplers, connect to tractor hydraulic circuits. • DO NOT UNFOLD OR FOLD TOOLBAR WITHOUT HITCHING TO THE TRACTOR. 1. Connect the toolbar hydraulic hoses to the tractor remote couplers. The 1/2” hoses supply oil to the toolbar lift cylinders.

  • Page 79: Jack Usage

    — Operation Legacy Jack Usage Parked Position Lower drop leg to contact the ground. Crank jack leg downward to completely remove the FIG. 3-4 hitch weight from tractor drawbar. (FIG. 3-4) Transport Position After tractor connection is established, raise jack leg of the jack to highest position to FIG.

  • Page 80: Transporting

    — Operation Legacy Transporting Drawbar Connection • THIS IMPLEMENT IS NOT EQUIPPED WITH BRAKES. ENSURE THAT THE TOWING VE- HICLE HAS ADEQUATE WEIGHT AND BRAKING CAPACITY TO TOW THIS IMPLEMENT. • IMMEDIATELY PRIOR TO ROAD TRANSPORT, RUN THE FULL FOLD SEQUENCE FOR PROPER SYSTEM PRESSURES AND TO AVOID INADVERTENT MOVEMENT.

  • Page 81: Leveling Machine

    — Operation Legacy Toolbar Operation (continued) Leveling Machine • Never unfold the unit without attaching to tractor first. Refer to “Hitching to the Tractor” and “Jack Usage” in this section. 1. Before leveling the machine the tire pressure should be checked. Inflate center section lugged tractor tires to 51 PSI maximum;...

  • Page 82: Leveling Adjustable Gauge Wheels

    — Operation Legacy Toolbar Operation (continued) Leveling Adjustable Gauge Wheels NOTE: Adjust until toolbar is level across the entire bar 1. Check tire pressure before adjusting. Loosen the two 1” x 4” hex bolts at the top of the adjust linkage. Loosen 1” hex nut on inside of threaded rod. Turn 1” hex nut on outside clockwise to lower wing and counter clockwise to raise wing.

  • Page 83: Pin Adjust Gauge Wheels

    — Operation Legacy Toolbar Operation (continued) Pin Adjust Gauge Wheels 1. Adjust pin adjust gauge wheel to level position with the hydraulic gauge wheel. FIG. 3-9 3-11...

  • Page 84: Depth Adjustment

    — Operation Legacy Toolbar Operation (continued) Depth Adjustment 1. One complete revolution equals 1/2” of depth increase. FIG. 3-11 JAP2584 LOCKED POSITION Locking Depth Adjustment Linkage 1. Rotate depth control adjuster latch over handle and lock in place with 1/4” x 2” FIG.

  • Page 85: Hydraulic System Charging

    — Operation Legacy Hydraulic System Charging ALWAYS RELIEVE HYDRAULIC SYSTEM PRESSURE BEFORE DISCONNECTING HOSES • FROM TRACTOR OR SERVICING HYDRAULIC SYSTEM. SEE TRACTOR OPERATOR’S MANUAL FOR PROPER PROCEDURES. HYDRAULIC SYSTEM MUST BE PURGED OF AIR BEFORE OPERATING TO PREVENT • SERIOUS INjURY OR DEATH.

  • Page 86: Folding Toolbar

    — Operation Legacy Folding Toolbar 1. Fold slowly! Check hoses, fittings and row mountings for folding interference or leaks. FIG. 3-14 21 Row 30” Spacing Shown FIG. 3-15 3-14...

  • Page 87: Nurse Tank Hitch

    — Operation Legacy Nurse Tank Hitch 1. Nurse tank hitch can be retracted and moved from side to side for easy hookup. Hitch will automatically lock in the extended position. NOTE: Periodically check latch mechanism to ensure proper latching in the extended position. FIG.

  • Page 88: Anhydrous Ammonia Operating Instructions

    — Operation Legacy Anhydrous Ammonia Operating Instructions • ALWAYS WEAR PERSONAL PROTECTIVE EQUIPMENT WHEN WORKING WITH OR NEAR CHEMICALS. THIS EQUIPMENT INCLUDES, BUT IS NOT LIMITED TO: PROTECTIVE EYE WEAR, GLOVES, SHOES, SOCKS, LONG-SLEEVED SHIRT, AND LONG PANTS. AD- DITIONAL PROTECTION MAY BE REQUIRED FOR MANY TYPES OF CHEMICALS. •...

  • Page 89: Disconnecting Nurse Tank

    — Operation Legacy Anhydrous Ammonia Operating Instructions (continued) Disconnecting Nurse Tank • ALWAYS WEAR PERSONAL PROTECTIVE EQUIPMENT WHEN WORKING WITH OR NEAR CHEMICALS. THIS EQUIPMENT INCLUDES, BUT IS NOT LIMITED TO: PROTECTIVE EYE WEAR, GLOVES, SHOES, SOCKS, LONG-SLEEVED SHIRT, AND LONG PANTS. AD- DITIONAL PROTECTION MAY BE REQUIRED FOR MANY TYPES OF CHEMICALS.

  • Page 90: Coupler Operations

    — Operation Legacy Coupler Operations • ALWAYS WEAR PERSONAL PROTECTIVE EQUIPMENT WHEN WORKING WITH OR NEAR CHEMICALS. THIS EQUIPMENT INCLUDES, BUT IS NOT LIMITED TO: PROTECTIVE EYE WEAR, GLOVES, SHOES, SOCKS, LONG-SLEEVED SHIRT, AND LONG PANTS. AD- DITIONAL PROTECTION MAY BE REQUIRED FOR MANY TYPES OF CHEMICALS. Coupler release handle Female coupler Male coupler neck...
  • Page 91 — Operation Legacy Coupler Operations (continued) Connecting 1. Stand on the upwind side. Close all feed-line valves and inspect all components for proper condition. 2. Relieve pressure in nurse tank hose between male coupler (F) and first shutoff valve towards nurse tank by carefully opening coupler bleed valve (E). The Squibb Flo-Max coupler is designed to re-couple safely with pressure on the female coupler half (B).

  • Page 92: Orifice Block Setting

    — Operation Legacy Orifice Block Setting To minimize the amount of ammonia going out the dump lines, follow the chart below to determine the dump orifice hose barb to use and install. The chart is based on GPM, gallons per minute. Use the formula below to determine your GPM then refer to the chart for the recommended dump orifice hose barb needed for your application.

  • Page 93: Clean Water Tank

    — Operation Legacy Clean Water Tank Change water daily to provide fresh clean water to flush exposed skin or eyes. Drain water daily in cold temperatures to prevent freezing and bursting tank. In case of exposure to anhydrous ammonia, open faucet or pull top end of hose loose to flush exposed part of body.

  • Page 94: Supershooter (Options)

    — Operation Legacy SuperShooter III SuperShooter (Options) Squibb Coupler Super Task Procedures Illustrations BodyGuard III Shooter III AM3514 See manual #J04000041 or J04000026 for complete operating procedures. Manual Number Manual 04000026 SUPERSHOOTER III 1 1/4” NPT OR 1 1/2” NPT SUPERSHOOTER III (MANUAL #j04000041) SQUIBB COUPLER...
  • Page 95 — Maintenance Legacy Section IV Maintenance Lubrication ..........................4-2 Legacy Maintenance ........................4-4 Seasonal Storage ......................... 4-4 Purging A Hydraulic System ....................4-5 Schematics ..........................4-6 Wheel, Hub and Spindle Disassembly and Assembly ............... 4-8 Wheels and Tires ........................4-10 Wheel Nut Torque Requirements ..................

  • Page 96: Lubrication

    — Maintenance Legacy Lubrication...
  • Page 97 — Maintenance Legacy Lubrication (continued) To keep your applicator in top operating condition and to assure its proper performance and reliability for a long period of time, periodic inspection and lubrication is a must. Use EP-2 lubricant at the locations described in the chart. All exposed cylinder rods should be coated with grease before seasonal storage to prevent rusting.

  • Page 98: Legacy Maintenance

    — Maintenance Legacy Legacy Maintenance • ELECTROCUTION WILL CAUSE SERIOUS INJURY OR DEATH. THE IMPLEMENT IS NOT INSULATED. KEEP AWAY FROM ALL ELECTRICAL LINES AND DEVICES. ELECTROCU- TION CAN OCCUR WITHOUT DIRECT CONTACT. • TIPPING OR MOVEMENT OF THE MACHINE CAN CAUSE SERIOUS INJURY OR DEATH. BE SURE MACHINE IS SECURELY BLOCKED.

  • Page 99: Purging A Hydraulic System

    — Maintenance Legacy Legacy Maintenance (continued) Coat exposed cylinder piston rods with rust FIG. 4-1 preventative material. Inspect machine for parts that may need to be replaced so they may be ordered in the off season. Lubricate machine at all points outlined. Post Check coulter hubs for free rotation.

  • Page 100: Schematics

    — Maintenance Legacy Schematics - Electrical Item No E.C. # AP3221 1461 ELECTRICAL HARNESS, 33' 7 PIN SAE J560 EXTENSION, Item Electrical Harness - Main 33’ (JAP3221) WITH 6-PIN LIGHTING CONNECTION CONNECTOR: 7 F-TERMINAL PLUG CONFORMING TO SAE J560 CONNECTOR: PACKARD, FLAT 6 M-TERMINAL WEATHER-PACK SHROUD CONNECTOR: 7 M-TERMINAL SOCKET CONFORMING TO SAE J560 CABLE: 5-WIRE 16AWG, (WHT, YEL, RED, GRN, BRN) TRAILER CABLE: 7-WIRE, 12AWG (BLK, YEL, GRN, BRN), 10AWG (RED, BLU),...
  • Page 101 — Maintenance Legacy Schematic — Electrical         Electrical Harness AG Plug to RV Socket (JAP3223)                   ...

  • Page 102: Wheel, Hub And Spindle Disassembly And Assembly

    — Maintenance Legacy Wheel, Hub and Spindle Disassembly and Assembly • TIPPING OR MOVEMENT OF THE MACHINE CAN CAUSE SERIOUS INJURY OR DEATH. BE SURE MACHINE IS SECURELY BLOCKED. • FALLING ObJECTS CAN CAUSE SERIOUS INJURY OR DEATH. DO NOT wORK UNDER THE MACHINE AT ANY TIME WHILE BEING HOISTED.
  • Page 103 — Maintenance Legacy Wheel, Hub and Spindle Disassembly and Assembly (continued) 5. Inspect the spindle and replace if necessary. If spindle does not need to be replaced, skip to Step 6; otherwise continue with Step 5. Remove the bolt and lock nut that retain the spindle to the axle. Using a lifting device rated for 200 lbs., remove the old spindle.

  • Page 104: Wheels And Tires

    — Maintenance Legacy Wheels and Tires Wheel Nut Torque Requirements • IMPROPERLY TORQUED wHEEL NUTS/bOLTS CAN CAUSE A LOSS OF IMPLEMENT CONTROL AND MACHINE DAMAGE. TORQUE wHEEL NUTS/bOLTS TO VALUES IN TAbLE. CHECK TORQUE bEFORE USE, AFTER ONE HOUR OF UNLOADED USE OR AFTER FIRST LOAD, AND EACH LOAD UNTIL wHEEL NUTS/bOLTS MAINTAIN TORQUE VALUE.

  • Page 105: Tire Pressure

    — Maintenance Legacy Wheels and Tires (continued) Tire Pressure The following is to be used as a general guide for tire inflation and figures can vary de- pending on specific brand of tire used. It is important that tires are inspected after unit is loaded.

  • Page 106: Complete Torque Chart

    — Maintenance Legacy Complete Torque Chart Capscrews - Grade 5 NOTE: • Grade 5 capscrews can be identified by three radial dashes on the head. • For wheel torque requirements, refer to Wheels and Tires. • Tighten U-bolts evenly and equally to have the same number of threads exposed on each end.
  • Page 107 — Maintenance Legacy Complete Torque Chart Capscrews - Grade 8 NOTE: • Grade 8 capscrews can be identified by six radial dashes on the head. • For wheel torque requirements, refer to Wheels and Tires. • Tighten U-bolts evenly and equally to have the same number of threads exposed on each end.

  • Page 108: Hydraulic Fittings - Torque And Installation

    — Maintenance Legacy Hydraulic Fittings – Torque and Installation SAE Flare Connection (J. I. C.) 1. Tighten nut with finger until it bottoms the seat. 2. Using a wrench, rotate nut to tighten. Turn nut 1/3 turn to apply proper torque. SAE Straight Thread O-Ring Seal 1.

  • Page 109: Nh3 Fittings - Torque And Installation

    — Maintenance Legacy NH3 Fittings – Torque and Installation NPT - NPTF Threads The proper method of assembling pipe threaded connectors is to assemble them finger tight and then wrench tighten further to the specified number of turns from finger tight (T.F.F.T.) given in the table below.
  • Page 110 — Maintenance Legacy Notes 4-16...
  • Page 111 — Parts Legacy SECTION V Parts Clean Water Tank Components ........5-2 Torsion Arm Basket (Short Arms) Components ... 5-58 Hitch, Transport Chain, Manual Holder and Jack ..5-4 Torsion Arm/Rigid Basket Mounting Brackets ..... 5-59 Depth Control Components ..........5-6 Basket Flat Mount with Hardware ......

  • Page 112: Clean Water Tank Components

    — Parts Legacy Clean Water Tank Components Please visit www.unverferth.com/parts/ for the most current parts listing.
  • Page 113 — Parts Legacy Clean Water Tank Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JAAM2427 Clean Water Tank & Toolbox INCLUDES ITEMS 1-10 JPKG00040 9 Gallon Clean Water Tank Package Includes Items 2-8...

  • Page 114: Hitch, Transport Chain, Manual Holder And Jack

    — Parts Legacy Hitch, Transport Chain, Manual Holder and Jack Components Please visit www.unverferth.com/parts/ for the most current parts listing. To Tractor...
  • Page 115 — Parts Legacy Hitch, Transport Chain, Manual Holder and Jack Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 45581B Clevis Hitch Assembly Includes Items 2-6 9928 Lock Nut/Top, 3/8”-16UNC JAM2144 Clevis Hitch JAM2145...

  • Page 116: Depth Control Components

    — Parts Legacy Depth Control Components Please visit www.unverferth.com/parts/ for the most current parts listing. To Tractor...
  • Page 117 — Parts Legacy Depth Control Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 9390-145 Capscrew, 3/4"-10UNC x 2" G5 9392-182 Roll Pin, 3/8" Dia. x 2 1/2" 9405-104 Flat Washer, 3/4” SAE 96732 Lock Nut/Center, 3/4"-10UNC...

  • Page 118: Main Frame Components

    — Parts Legacy Main Frame Components Please visit www.unverferth.com/parts/ for the most current parts listing. To Tractor Position For Tractor Tires Position For Truck Tire Duals...
  • Page 119 — Parts Legacy Main Frame Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 9390-130 Capscrew, 5/8"-11UNC x 3 1/2" G5 9390-132 Capscrew, 5/8"-11UNC x 4" G5 9390-189 Capscrew, 1"-8UNC x 3 1/2" G5 9390-191 Capscrew, 1"-8UNC x 4"...

  • Page 120: Primary Wing Components

    — Parts Legacy Primary Wing Components Please visit www.unverferth.com/parts/ for the most current parts listing. To Tractor 5-10...
  • Page 121 — Parts Legacy Primary Wing Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 9801 Lock Nut/Top, 5/8”-11UNC 9404-029 Lock Washer, 5/8” JBP3354 U-Bolt 5/8”-11UNC x 7 3/4”, 6 11/16”CC 91174 Machinery Bushing, 1 7/8” OD x 1 1/4” ID x 14GA 9390-057 Capscrew, 3/8”-16UNC x 1 1/2”...

  • Page 122: Secondary 5'8" Wing Components

    — Parts Legacy Secondary 5’8” Wing Components Please visit www.unverferth.com/parts/ for the most current parts listing. To Tractor 5-12...
  • Page 123 — Parts Legacy Secondary 5’8” Wing Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 81145SM Mounted Tire & Wheel Includes Items 2A, 2B, 2C W615-6SM 6 x 15 Implement Wheel Not Shown Tire TL7.6B15 8-Ply...

  • Page 124: Secondary 3'2" Wing Components

    — Parts Legacy Secondary 3’2” Wing Components Please visit www.unverferth.com/parts/ for the most current parts listing. 5-14...
  • Page 125 — Parts Legacy Secondary 3’2” Wing Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 9390-059 Capscrew, 3/8"-16UNC x 2" G5 9390-061 Capscrew, 3/8"-16UNC x 2 1/2" G5 9390-145 Capscrew, 3/4”-10UNC x 2” G5 9398-012 Elastic Lock Nut, 3/8"-16UNC...

  • Page 126: Secondary Wing Extension To 50 Ft

    — Parts Legacy Secondary Wing Extension to 50 Ft. Please visit www.unverferth.com/parts/ for the most current parts listing. To Tractor 5-16...
  • Page 127 — Parts Legacy Secondary Wing Extension to 50 Ft. Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 9003735 Cable Tie 11 x 0.30 91174 Machinery Bushing, 1 7/8" OD x 1 1/4" ID x 14GA...

  • Page 128: Straight Extension Kit

    — Parts Legacy Straight Extension Kit Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES J55000106BB Straight Extension Kit 28” Bundle Includes Items 1-4A J55000107 Straight Extension Kit 14” Bundle Includes Items 1-4B 9390-149 Capscrew, 3/4”-10UNC x 3” G5 9394-016 Hex Nut, 3/4"-10UNC...

  • Page 129: Pin Adjust Gauge Wheel Leg Assembly

    — Parts Legacy Pin Adjust Gauge Wheel Leg Assembly (JAM24024) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION 9162 Hub Cap 9391-036 Cotter Pin, 5/32” Dia. x 1 3/4” 9393-020 Slotted Nut, 1”-14UNS JEM3700 Gauge Wheel Leg Weldment, Pin Adjust...

  • Page 130: Dual Wheel Lift With 385/65R22.5 Tires

    — Parts Legacy Dual Wheel Lift with 385/65R22.5 Tires (J66000127) Please visit www.unverferth.com/parts/ for the most current parts listing. Right-Hand Wheel Leg Valve Stems to the Inside Left-Hand Wheel Leg Valve Stems to the Inside 5-20...
  • Page 131 — Parts Legacy Dual Wheel Lift with 385/65R22.5 Tires (J66000127) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 9390-132 Capscrew, 5/8”-11UNC x 4” G5 9398-019 Elastic Lock Nut, 5/8”-11UNC 111274SM Wheel and Tire Assembly 11.75x22.5/65R22.5 Includes Valve Stem, Tire &...

  • Page 132: Dual Wheel Lift With 295/75R22.5 Tires

    — Parts Legacy Dual Wheel Lift with 295/75R22.5 Tires (J66000124) Please visit www.unverferth.com/parts/ for the most current parts listing. Right-Hand Wheel Leg Valve Stems to the Outside Left-Hand Wheel Leg Valve Stems to the Outside 5-22...
  • Page 133 — Parts Legacy Dual Wheel Lift with 295/75R22.5 Tires (J66000124) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES J66000124 Dual Wheel Lift with 295/75R22.5 Tires Includes Items 1-15 9390-132 Capscrew, 5/8”-11UNC x 4” G5 9398-019 Elastic Lock Nut, 5/8”-11UNC...

  • Page 134: Single Wheel Lift Components

    — Parts Legacy Single Wheel Lift Components (J66000104) Please visit www.unverferth.com/parts/ for the most current parts listing. Right-Hand Wheel Leg Left-Hand Wheel Leg NOTE: Valve stem on each wheel is positioned to the inside on 30”, 15” and 20”. 5-24...
  • Page 135 — Parts Legacy Single Wheel Lift Components (J66000104) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JAM6226 Wheel Leg Weldment, LH Includes Items 2 & 3 JBP3538 Split Tension Bushing 2” OD x 1 3/4” ID x 1 1/2”...

  • Page 136: Hub And Spindle Components

    — Parts Legacy Hub and Spindle Components (JAAM2800) For 295/75R22.5 Tires Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 9247 Bearing Cone, 1.625” Bore (LM501349) TA37809 Cotter Pin, 7/32” Dia. x 1 3/4” JAP2171 Spindle, 2 3/4”...
  • Page 137 — Parts Legacy Hub and Spindle Components (JAAM2800-1) For 385/65R22.5 Tires Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 9247 Bearing Cone, 1.625” Bore (LM501349) TA37809 Cotter Pin, 7/32” Dia. x 1 3/4” JAP2171 Spindle, 2 3/4”...
  • Page 138 — Parts Legacy Hub and Spindle Components (JAAM2788-1) For 385/85R34 Tires Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 9247 Bearing Cone, 1.625” Bore (LM501349) TA37809 Cotter Pin, 7/32” Dia. x 1 3/4” 9442B Hub Cap, 3.125”...

  • Page 139: Decals

    — Parts Legacy Decals Please visit www.unverferth.com/parts/ for the most current parts listing. Installed on bottom side ITEM PART NUMBER DESCRIPTION NOTES JAP2215 Decal, BLU-JET, 3” X 8” 94094 Decal, WARNING “Rising or Falling Tongue” 91605 Decal, FEMA 97337 Decal, WARNING “Folding or Unfolding Wings”...

  • Page 140: Main Frame To Primary Wing Hydraulics

    — Parts Legacy Main Frame to Primary Wing Hydraulics Please visit www.unverferth.com/parts/ for the most current parts listing. Hose End To Rod End Of Hose End To Base End Of Main Frame Secondary RH Wing Gauge RH Transport Wheel Cylinder...
  • Page 141 — Parts Legacy Main Frame to Primary Wing Hydraulics Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JDP4398-1 Cylinder 5” x 36” w/2 3/4” Spacer 98801 Reducer 7/8-14 O-Ring Male x 3/4-16 O-Ring Female...

  • Page 142: Main Frame Transport Wheel & Depth Control Hydraulics

    — Parts Legacy Main Frame Transport Wheel & Depth Control Hydraulics Please visit www.unverferth.com/parts/ for the most current parts listing. 5-32...
  • Page 143 — Parts Legacy Main Frame Transport Wheel & Depth Control Hydraulics Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JAM2090 Depth Collar & Lock-Up Storage Bracket JAM6280 Transport Lock 9514 Hairpin Cotter 0.092” Dia. x 1 7/8”...

  • Page 144: Wing Gauge Wheel Hydraulics

    — Parts Legacy Wing Gauge Wheel Hydraulics Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JBM3559 Clevis Pin Weldment 1” Dia. x 3 7/8” 9405-118 Flat Washer, 1” USS 9391-045 Cotter Pin, 3/16” Dia. x 1 3/4”...

  • Page 145: Primary Wing To Secondary Wing Hydraulics

    — Parts Legacy Primary Wing to Secondary Wing Hydraulics Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JDP4579 Cylinder 4 1/2” x 20” 98079 90° Elbow 916-18 JIC Male x 7/8-14 O-Ring Male JDP5314 Hydraulic Hose, 3/8”...

  • Page 146: Secondary Wing Extension Hydraulics (52' Units Only)

    — Parts Legacy Secondary Wing Extension Hydraulics (52’ Units ONLY) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JDP4579 Cylinder 4 1/2” x 20” 91465 Tee 9/16-18 JIC Male x 9/16-18 JIC Female x 9/16-18 JIC Male...

  • Page 147: Coulter Mounting Bracket Components

    — Parts Legacy Coulter Mounting Bracket Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JAAM2428 Coulter Mounting Bracket Assembly Includes Items 1-4 9388-108 Carriage Bolt, 1/2”-13UNC x 2 1/2” G5 9800 Lock Nut/Top, 1/2”-13UNC...

  • Page 148: Offset Stagger Bracket & Bracket Extension

    — Parts Legacy Offset Stagger Bracket & Bracket Extension Components Please visit www.unverferth.com/parts/ for the most current parts listing. 5-38...
  • Page 149 — Parts Legacy Offset Stagger Bracket & Bracket Extension Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JAAM2141BB Offset Stagger Bracket w/Hdw 22” x 8”, 6” x 6” Mounting Includes Items 2-4 JAM4510BB Offset Stagger Bracket Weldment 22”...

  • Page 150: Super 1200 Flex Coulter Hub Assembly Components

    — Parts Legacy Super 1200 Flex Coulter Hub Assembly Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JAP2707 HUB ASSEMBLY, 4 BOLT 90024 HUB CAP, 1610 JAP2706-1 HUB W/ CUPS, 4 BOLT, 5” BC, 3.62” PILOT, W/ZERK HOLE...

  • Page 151: Super 1200 Flex Coulter Assembly Components

    — Parts Legacy Super 1200 Flex Coulter Assembly Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTE JAM2799 ASSEMBLY, COULTER ARM WITH HUB & KNEE CASTING, HD JAM2743B CASTING, COULTER KNEE, HD, MACHINED WITH BUSHINGS JAP2274 BUSHING, 1-17/32”...
  • Page 152 — Parts Legacy SealPro II (JAAM2856) & Blades For 1 1/4” Edge Bent Shank Please visit www.unverferth.com/parts/ for the most current parts listing. Coulter Blade Fluted Blade 20” JAP2701 Blade Options JAM2479 JAP2728 17” Notched Blade 17” Wavy 5-42...
  • Page 153 — Parts Legacy SealPro II (JAAM2856) & Blades For 1 1/4” Edge Bent Shank Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JAAM2856 SealPro II, 1 1/4” Edge Bent Shank, 1 Row Includes Items 1-29...

  • Page 154: Disccover Sealer

    — Parts Legacy DiscCover Sealer (JAAM2893) For 1 1/4” Edge Bent Shank Please visit www.unverferth.com/parts/ for the most current parts listing. 5-44...
  • Page 155 — Parts Legacy DiscCover Sealer (JAAM2893) For 1 1/4” Edge Bent Shank Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JAAM2893 DiscCover Sealer, 1 1/4" Edge Bent Shank, 1 Row Includes Items 1-23 JAM2485...
  • Page 156 — Parts Legacy Disc Sealer Spring Add-On Kit (JAAM2857) Optional Please visit www.unverferth.com/parts/ for the most current parts listing. (BLaDES NOT INcLuDED) (BLaDES NOT INcLuDED) ITEM PART NUMBER DESCRIPTION NOTES JAAM2857 Disc Sealer Spring Add-On Kit Option (Blades Not Included)

  • Page 157: Sealer Hanger With Blade Mounting

    — Parts Legacy Sealer Hanger with Blade Mounting (JAM2481) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JAM2481 Sealer Hanger Assembly with Blade Mounting Includes Items 1-14 JAM2482 Hub Cap Retainer JAP2216 Decal, BLU-JET (1 1/2" x 4) 91821 Bearing Cone #L44649 (1.0625"...

  • Page 158: Row Clamp W/Edgebent Shank & Coulter Mount

    — Parts Legacy Row Clamp w/EdgeBent Shank & Coulter Mount (JAAM2132) Please visit www.unverferth.com/parts/ for the most current parts listing. NOTE: No threads in shear area. 5-48...
  • Page 159 — Parts Legacy Row Clamp w/EdgeBent Shank & Coulter Mount (JAAM2132) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JAAM2132 Row Clamp with EdgeBent Shank & Coulter Mount 6” x 6” Includes Items 1-17...

  • Page 160: Shank Assembly 1 1/4" Edgebent Scs Less Coulter

    — Parts Legacy Shank Assembly 1 1/4” EdgeBent SCS Less Coulter (JAAM2134) Please visit www.unverferth.com/parts/ for the most current parts listing. 5-50...
  • Page 161 — Parts Legacy Shank Assembly 1 1/4” EdgeBent SCS Less Coulter (JAAM2134) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 44822B Spring Bundle Assembly, EdgeBent Shank Includes Items 2-12 JAM2156 Spring Sleeve Weldment 9006849...

  • Page 162: Row Clamp, 1 1/4" Edgebent Maxpac

    — Parts Legacy Row Clamp, 1 1/4” EdgeBent MaxPac w/Shank & Coulter Mount Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JAAM2135 Row Clamp, 1 1/4” EdgeBent MaxPac w/Shank & Coulter Mount Includes Items 1-13...

  • Page 163: Maxpac Basket Mount Arm Components

    — Parts Legacy MaxPac Basket Mount Arm Components (JAAM2623) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JAAM2623 MaxPac Basket Mount (AR700) Includes Items 1-5 JAM2271 MaxPac Basket Mount Weldment JAM2273 Nut Plate Weldment 9390-101 Capscrew, 1/2”-13UNC x 1 1/2”...

  • Page 164: Maxpac Mount With Edgebent Shank Bundle

    — Parts Legacy MaxPac Mount with Edgebent Shank Bundle #43599 Please visit www.unverferth.com/parts/ for the most current parts listing. 5-54...
  • Page 165 — Parts Legacy MaxPac Mount with Edgebent Shank Bundle #43599 Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 43599 Max Pac Shank Mount w/ 1 1/4” Edge-Bent Shank Assembly Includes Items 1-47 44429 Max Pac Shank Assembly...

  • Page 166: Coulter Bracket Extension 9 7/8" Kit

    — Parts Legacy Coulter Bracket Extension 9 7/8” Kit (JAAM2637) Please visit www.unverferth.com/parts/ for the most current parts listing. NOTE: Used when residue managers are mounted on coulters. ITEM PART NUMBER DESCRIPTION NOTES JAAM2637 Coulter Bracket Extension 9 7/8” Kit, 1 Row...

  • Page 167: Coulter Bracket Extension 16 7/8" Kit

    — Parts Legacy Coulter Bracket Extension 16 7/8” Kit (JAAM2852) Please visit www.unverferth.com/parts/ for the most current parts listing. NOTE: Use when residue managers are mounted on coulters, SCS Spring Cushion. ITEM PART NUMBER DESCRIPTION NOTES JAAM2852 Coulter Bracket Extension 16 7/8” Kit, 1 Row...

  • Page 168: Torsion Arm Basket (Short Arms) Components

    — Parts Legacy Torsion Arm Basket (Short Arms) Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES J70210641 Torsion Arm & 12 3/4” Basket Assembly, Short Includes Items 1-16 JAM2269 Strip-Till Basket Mount, Short (18 3/4”)

  • Page 169: Torsion Arm/Rigid Basket Mounting Brackets

    Legacy Torsion Arm/Rigid Basket Mounting Brackets Rigid Fertilizer Rows - 6” x 6” - Bundle #J70210592 Rigid Fertilizer Rows - 4” x 6” - Bundle #J70210591 Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES...

  • Page 170: Basket Flat Mount With Hardware

    — Parts Legacy Basket Flat Mount with Hardware 6” x 6” Mounting - Bundle #JAAM2630 4” x 6” Mounting - Bundle #JAAM2722 Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JAAM2630 Basket Flat Mount w/Hardware, For 6x6 Mounting...

  • Page 171: Residue Manager Blade Mounting Assembly

    — Parts Legacy Residue Manager Blade Mounting Assembly (JAM7670) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JAM7670 Residue Manager Blade Mounting Assembly Includes Items 1-9 9789 Bearing Cone, .750” ID (LM11949) 9391-023 Cotter Pin, 1/8” Dia. x 1”...

  • Page 172: Striptill Residue Manager Components

    — Parts Legacy StripTill Residue Manager Components (J70210646) Please visit www.unverferth.com/parts/ for the most current parts listing. 5-62...
  • Page 173 — Parts Legacy StripTill Residue Manager Components (J70210646) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES J70210646 StripTill Residue Manager, 1 Row Includes Items 1-26 JAM2489 Lower Clevis Plate JAM2490 Upper Spring Tube JAM2491...

  • Page 174: Supershooter Hitch Assembly Components

    — Parts Legacy SuperShooter Hitch Assembly Components Please visit www.unverferth.com/parts/ for the most current parts listing. 5-64...
  • Page 175 — Parts Legacy SuperShooter Hitch Assembly Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JPKG00234BB SuperShooter Hitch Package Includes Item 2-17 JAAM2931BB Assembly, SuperShooter Hitch, Auto-Lok, Without Pin JAM6220BB Hitch Mounting Bracket JAM6273BB...

  • Page 176: Supershooter Hitch, Low Mounting Components

    — Parts Legacy SuperShooter Hitch, Low Mounting Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JPKG00247BB SuperShooter Hitch Assembly, Low Mounting Includes Item 2-17 JAAM2931BB Assembly, SuperShooter Hitch, Auto-Lok, Without Pin JAM6234BB Bracket, Low Hitch Mounting, At6020 SuperShooter...

  • Page 177: Auto-Lok Supershooter Hitch Components

    — Parts Legacy Auto-Lok SuperShooter Hitch Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 902875 Lock Nut/Center, 3/8”-16UNC 91160 Grease Zerk 1/4”-28 STT 91192 Retaining Ring, 1" 91299-157 Capscrew, 3/4”-10UNC x 6” G8 9390-055 Capscrew, 3/8”-16UNC x 1”...

  • Page 178: Supershooter Iii Connection Single 1.25" Plumbing

    — Parts Legacy SuperShooter III Connection - Single 1.25” Plumbing Please visit www.unverferth.com/parts/ for the most current parts listing. 5-68...
  • Page 179 — Parts Legacy SuperShooter III Connection - Single 1.25” Plumbing Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 44258B Support Mounting Plate 44260B Inlet Plumbing Support Plate 44568 Leak Test Tag (Double Sided) 44635 NH3 Supply Plumbing Assembly - Single 1.25”...

  • Page 180: Supershooter Iii Connection Double 1.25" Plumbing

    — Parts Legacy SuperShooter III Connection - Double 1.25” Plumbing Please visit www.unverferth.com/parts/ for the most current parts listing. 5-70...
  • Page 181 — Parts Legacy SuperShooter III Connection - Double 1.25” Plumbing Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 44258B Support Mounting Plate 44568 Leak Test Tag (Double Sided) Includes 44678 NH3 Supply Plumbing Assembly - Double 1.25”...

  • Page 182: Supershooter Iii Components - 1.25" Connection

    — Parts Legacy SuperShooter III Components - 1.25” Connection (JAAM3514) Please visit www.unverferth.com/parts/ for the most current parts listing. 5-72...
  • Page 183 — Parts Legacy SuperShooter III Components - 1.25” Connection (JAAM3514) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JAAM3514 SuperShooter III / 1 1/4” Squibb Coupler / Bodyguard III Includes Items 2-32 JAM7634 Valve Mounting Weldment...

  • Page 184: Supershooter Iii Single 1 1/4" Assembly

    — Parts Legacy SuperShooter III Single 1 1/4” Assembly, Less Distribution Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES J66000136 SuperShooter III Single 1 1/4” Assembly, Less Distribution Includes Items 1-12 JAAM3514 SuperShooter III / 1 1/4” Squibb Coupler / Bodyguard III...

  • Page 185: Supershooter Iii Max Single 1 1/2" Assembly

    — Parts Legacy SuperShooter III Max Single 1 1/2” Assembly, Less Distribution Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES J66000150 SuperShooter III Max Single 1 1/2” Assembly, Less Distribution Includes Items 1-12 JAAM3516 SuperShooter III Max / 1 1/2”...

  • Page 186: Supershooter Iii Connection Single 1.5" Plumbing

    — Parts Legacy SuperShooter III Connection - Single 1.5” Plumbing Please visit www.unverferth.com/parts/ for the most current parts listing. 5-76...
  • Page 187 — Parts Legacy SuperShooter III Connection - Single 1.5” Plumbing Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 44258B Support Mounting Plate 44260B Inlet Plumbing Support Plate 44568 Leak Test Tag (Double Sided) Includes Items 44690 NH3 Supply Plumbing Assembly - Single 1.5”...

  • Page 188: Supershooter Iii Connection Double 1.5" Plumbing

    — Parts Legacy SuperShooter III Connection - Double 1.5” Plumbing Please visit www.unverferth.com/parts/ for the most current parts listing. 5-78...
  • Page 189 — Parts Legacy SuperShooter III Connection - Double 1.5” Plumbing Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 44258B Support Mounting Plate 44568 Leak Test Tag (Double Sided) Includes 44679 NH3 Supply Plumbing Assembly - Double 1.5”...

  • Page 190: Supershooter Iii Components - 1.5" Connection

    — Parts Legacy SuperShooter III Components - 1.5” Connection (JAAM3516) Please visit www.unverferth.com/parts/ for the most current parts listing. 5-80...
  • Page 191 — Parts Legacy SuperShooter III Components - 1.5” Connection (JAAM3516) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES JAAM3516 SuperShooter III Max / 1 1/2” Squibb Coupler / Bodyguard III Includes Items 2-36 JAM7635...

  • Page 192: Impellicone And Mounting Hardware

    — Parts Legacy Impellicone and Mounting Hardware - 2 Section John Blue Please visit www.unverferth.com/parts/ for the most current parts listing. 5-82...
  • Page 193 — Parts Legacy Impellicone and Mounting Hardware - 2 Section John Blue Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION 43692 NH3 Applicator 2-Section/13-Port 44669 NH3 Applicator 2-Section/6-Port 44263B Distribution Tee Mounting Bracket =Black= JDP4037 Pipe Tee 1 1/4-11.5 NPT Female...
  • Page 194 — Parts Legacy Impellicone and Mounting Hardware - 3 Section John Blue Please visit www.unverferth.com/parts/ for the most current parts listing. 5-84...
  • Page 195 — Parts Legacy Impellicone and Mounting Hardware - 3 Section John Blue Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION 43748 NH3 Applicator 3-Section/6-Port 43436 NH3 Applicator 3-Section/13-Port 44117B Splitter Mounting Bracket Weldment =Black= 91263 Nut/Large Flange 3/8”-16UNC...
  • Page 196 — Parts Legacy Impellicone and Mounting Hardware - 4 Section John Blue Please visit www.unverferth.com/parts/ for the most current parts listing. 16 ROW 30” 17 ROW 30” 18 ROW 30” 19 ROW 30” 21 ROW 30” 24 ROW 20” 5-86...
  • Page 197 — Parts Legacy Impellicone and Mounting Hardware - 4 Section John Blue Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION 43437 NH3 Applicator 4-Section/6-Port 44117B Splitter Mounting Bracket Weldment =Black= 91263 Nut/Large Flange 3/8”-16UNC 92350 Plug, 1/4”-18 NPTF Male w/Square Head...

  • Page 198: Manifold And Mounting Hardware

    — Parts Legacy Manifold and Mounting Hardware - 2 Section Continental Please visit www.unverferth.com/parts/ for the most current parts listing. 9 PORT SHOWN 10 PORT SHOWN 8 PORT SHOWN 5-88...
  • Page 199 — Parts Legacy Manifold and Mounting Hardware - 2 Section Continental Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION 45312B NH3 Applicator 2-Section/6-Port 43419 NH3 Applicator 2-Section/7-Port 44862 NH3 Applicator 2-Section/8-Port 43749 NH3 Applicator 2-Section/9-Port...
  • Page 200 — Parts Legacy Manifold and Mounting Hardware - 3 Section Continental Please visit www.unverferth.com/parts/ for the most current parts listing. 6 PORT SHOWN 7 PORT SHOWN 8 PORT SHOWN 5 PORT SHOWN 5-90...
  • Page 201 — Parts Legacy Manifold and Mounting Hardware - 3 Section Continental Please visit www.unverferth.com/parts/ for the most current parts listing. PART ITEM DESCRIPTION NUMBER 45313B NH3 Applicator 3-Section/4-Port 43750 NH3 Applicator 3-Section/5-Port 43751 NH3 Applicator 3-Section/6-Port 44024 NH3 Applicator 3-Section/7-Port...
  • Page 202 — Parts Legacy Manifold and Mounting Hardware - 4 Section Continental Please visit www.unverferth.com/parts/ for the most current parts listing. 4 PORT SHOWN 4 PORT SHOWN 5 PORT SHOWN 6 PORT SHOWN 5-92...
  • Page 203 — Parts Legacy Manifold and Mounting Hardware - 4 Section Continental Please visit www.unverferth.com/parts/ for the most current parts listing. PART ITEM DESCRIPTION NUMBER 45361B NH3 Applicator 4-Section/4-Port 44028 NH3 Applicator 4-Section/5-Port 43441 NH3 Applicator 4-Section/6-Port 44508B Splitter Mounting Bracket 91432 90°...

  • Page 204: Distribution 2-Section Hoses And Electrical

    Legacy Distribution 2-Section Hoses and Electrical Components Please visit www.unverferth.com/parts/ for the most current parts listing. NOTE: 3/8” EVA hose comes partially pre-cut to length. Length of hose is determined by width of toolbar. Number of pre-cut sections are determined by number of rows.
  • Page 205 — Parts Legacy Distribution 2-Section Hoses and Electrical Components Please visit www.unverferth.com/parts/ for the most current parts listing. QTY PER DISTRIBUTION SIZE 2-SECTION JOHN BLUE & CONTINENTAL PART ITEM DESCRIPTION NUMBER 46043 Manifold Hose Routing Package 46046 Manifold Hose Routing Package...

  • Page 206: Distribution 3-Section Hoses And Electrical

    Legacy Distribution 3-Section Hoses and Electrical Components Please visit www.unverferth.com/parts/ for the most current parts listing. NOTE: 3/8” EVA hose comes partially pre-cut to length. Length of hose is determined by width of toolbar. Number of pre-cut sections are determined by number of rows.
  • Page 207 — Parts Legacy Distribution 3-Section Hoses and Electrical Components Please visit www.unverferth.com/parts/ for the most current parts listing. QTY PER DISTRIBUTION SIZE 3-SECTION JOHN BLUE & CON- TINENTAL PART ITEM DESCRIPTION NUMBER 46059 Manifold Hose Routing Package 46061 Manifold Hose Routing Package...

  • Page 208: Distribution 4-Section Hoses And Electrical

    Legacy Distribution 4-Section Hoses and Electrical Components Please visit www.unverferth.com/parts/ for the most current parts listing. NOTE: 3/8” EVA hose comes partially pre-cut to length. Length of hose is determined by width of toolbar. Number of pre-cut sections are determined by number of rows.
  • Page 209 — Parts Legacy Distribution 4-Section Hoses and Electrical Components Please visit www.unverferth.com/parts/ for the most current parts listing. QTY PER DISTRIBUTION SIZE 4-SECTION JOHN BLUE & CONTINENTAL PART ITEM DESCRIPTION NUMBER 46069 Manifold Hose Routing Package 46070 Manifold Hose Routing Package...

  • Page 210: 1.5" Flow Control Valve

    — Parts Legacy 1.5” Flow Control Valve Please visit www.unverferth.com/parts/ for the most current parts listing. Single 1.5" Flow Control Kit #43426 Dual 1.5" Flow Control Kit #43742 5-100...
  • Page 211 — Parts Legacy 1.5” Flow Control Valve Please visit www.unverferth.com/parts/ for the most current parts listing. Single Dual PART 1.5” Flow 1.5” Flow ITEM DESCRIPTION NUMBER Control Kit Control Kit #43426 #43742 9503297 Gauge Tree Manifold Weldment 9503299 Pressure Transducer 1-5 Volt, 0-250 PSI 9503333 Pipe Nipple 1/2”...

  • Page 212: Flow Control Valve (Optional)

    — Parts Legacy 1.0” Flow Control Valve (Optional) Please visit www.unverferth.com/parts/ for the most current parts listing. Single 1.0" Flow Control Kit #43427 ITEM Dual 1.0" Flow Control Kit #43428 5-102...
  • Page 213 — Parts Legacy 1.0” Flow Control Valve (Optional) Please visit www.unverferth.com/parts/ for the most current parts listing. Single Dual PART 1.0” Flow 1.0” Flow ITEM DESCRIPTION NUMBER Control Kit Control Kit #43427 #43428 44638B Support Bracket 84735B Clamp Casting 9503299...

  • Page 214: Cooler - Vortex

    — Parts Legacy Cooler - Vortex Please visit www.unverferth.com/parts/ for the most current parts listing. 5-104...
  • Page 215 — Parts Legacy Cooler - Vortex Please visit www.unverferth.com/parts/ for the most current parts listing. 50 GPM Cooler 80 GPM Cooler ITEM PART NUMBER DESCRIPTION Kit #43701 Kit #43429 44241B Mounting Plate 46126B Mounting Bracket 44460 EVA Tubing, 1.31" OD x 1.0" ID x 180", Reinforced 44461 EVA Tubing, 1.0"...

  • Page 216: Cooler - Continental

    — Parts Legacy Cooler - Continental (Optional) Please visit www.unverferth.com/parts/ for the most current parts listing. 5-106...
  • Page 217 — Parts Legacy Cooler - Continental (Optional) Please visit www.unverferth.com/parts/ for the most current parts listing. Single Dual PART ITEM DESCRIPTION Cooler Kit Cooler Kit NUMBER #43424 #43425 44241B Mounting Plate 44275B Flow Control Support Plate 44462 EVA Tubing, 0.59” OD x 3/8” ID x 84”...

  • Page 218: Isobus Rate Controller

    — Parts Legacy ISOBUS Rate Controller Please visit www.unverferth.com/parts/ for the most current parts listing. PART ITEM DESCRIPTION NOTES NUMBER 43836 ISOBUS Rate Controller 44277B RCM Mounting Plate 9000106 Cable Tie 7 1/2” 9005916 Foot Switch, ISO NODE w/Harness 9008095...

  • Page 219: Raven 450 Rate Controller Option

    — Parts Legacy Raven 450 Rate Controller Option Please visit www.unverferth.com/parts/ for the most current parts listing. PART ITEM DESCRIPTION NOTES NUMBER 43443 Raven 450 Rate Controller 9000106 Cable Tie 7 1/2” 9007549 Harness - Console 9503298 Temperature Gauge 9503395 Wire Harness, Console 10 Ft.

  • Page 220: Lighting Components

    — Parts Legacy Lighting Components Please visit www.unverferth.com/parts/ for the most current parts listing. 5-110...
  • Page 221 — Parts Legacy Lighting Components Please visit www.unverferth.com/parts/ for the most current parts listing. PART ITEM DESCRIPTION NOTES NUMBER Lighting Kit, Includes Items 1-27, J41000023 For 12/13/15/16/17/18/19 Row 30” Spacing Units 29-30 Includes Items 2-3, J41000024 Lighting Kit, For 20 & 21 Row 30” Spacing Units...
  • Page 222 L:\MaNuaLS\BLu-JET\J0605010\\DEcEMBER 2021-1//JuLY 2022-2...

Table of Contents