Aiphone JDW-C Installation Manual

Do not disassemble
or alter.
Do not disassemble or alter this
equipment. Doing so would be
dangerous. Fire or electric shock
could result.
Wall gasket
\
Electric shock caution
Do not touch the main unit with
damp or wet hands. Electric shock
and equipment damage could
result. When existing chime wiring
is used, it is possible that it contains
AC power. This can cause
equipment damage and electric
shock. Have the installation done
by an electrical contractor, low
voltage contractor, or qualified
personnel.
A
4ny place too close to a source
If electrical noise, for example a
xoadcasting station or wireless
station of any kind.
Any place where the detection
area or camera angle of view will
be blocked off.
0305
@
Accessories
Installation manual (this document) x 1
Sensor detection area adjustment sheet x 1
Manual for adjusting sensor detection area x 1 Mounting screws x 2
W Precaution notation
This installation manual uses various symbols for the sake of safe usage.
The results that can occur from ignoring these indications and handling this equipment incorrectly are categorized as follows.
*No power is being supplied from the
master station.
Wire the master station correctly to supply power.
The wiring is incorrect or a line is open or
shorted.
Wire correctly. (See "MOUNTING AND CONNECTION".)
DThe unit does
not operate.
'The unit was wired to the master station
with power supplied.
Keep the power OFF until the wiring is completed.
Icon display example
@
symbol indicates a prohibition. The specific content
prohibited is drawn in or near the figure. (For the figure
on the left, disassembly is prohibited.)
@
symbol indicates behavior that is mandatory and gives
Q
directions.
The master station select switch setting is
reversed.
Set "A" and "B" correctly. (See "SETTINGS".)
When you open up the package, make sure all the accessories are present.
JDW-C
The detection area is not correctly set. .Check the detection area and camera angle of view area and install so that
people are detected. (See ''ADJUSTMENTS''.)
This indicates that ignoring the contents of
the warning and handling the equipment
injury.
A w A
R N I N G
incorrectly can result in death or severe
This indicates that ignoring the contents of
the waming and handling the equipment
ACAUTION
incorrectly can result in personal injury
ndor damage to equipment.
People are passing nearly directly under
the sensor camera.
Adjust the upldown angle to point down so that they are detected.
.This is not a breakdownt. Because of the characteristics of a heat ray type
sensor, it may have difficulty detecting people coming directly at the camera.
As much as possible, install in such a way that people cut across the detection
area. (See "ADJUSTMENTS".)
This product is weather resistant,
but do not install it in a bathing
room or other place with extremely
high humidity, any place where
Do not spray water directly on this
equipment, for example with a hose.
Fire, electric shock, and equipment
damage could result.
water might get into it, or in water.
People are coming directly at the camera.
Use in areas with water
or high humidity is
prohibited.
BThe system does
not detect
people.
*Connect an external sensor in "OR mode" so that people cut across the
detection area. (See "SETTINGS".)
ur"t
This is not a breakdown. A heat ray type sensor cannot detect objects through
glass. Install in a place where the detection area is not cut off by the glass.
(See "MOUNTING AND CONNECTION".)
The detection area is cut off by glass.
This is not a breakdown. Set the detection area for each sensor so that people
are detected by both sensors. (See "SETTINGS".)
With the external sensor input function in
"AND mode", people are only detected
by the main sensor or by the external
sensor but not by both.
* The internal sensor switch is "OFF".
Install securely to a solid location
so that the equipment can not drop
from its own weight. Equipment
falling could result in injury.
Q
Install securely.
Switch "ON" the internal sensor switch.
The speaker select switch is "OFF". Switch "ON" the speaker select switch.
Main unit cover
Camera window
-A
CAUTION
- 1
@Sound cannot be
heard from the
unit.
'The master station select switch is "B" -Switch the master station select switch to "A". (Sound cannot be heard from
the unit when the master station is JA-2MECD or JA-2MCD.)
r
Be careful not to soil or damage.
1
The wiring is incorrect or a line is open or
shorted.
Wire correctly. (See " M 0 U " G AND CONNECTION".)
Notice
This product detects a person, provides notice, and shoots images. It is not an anti-theft device.
Aiphone does not bear responsibility for any damage incurred in the event of theft or other such incident.
@Sound cannot be
heard from the
master station.
The mic. sensitivity volume is at the
"Low" side.
Turn the mic. sensitivity volume to the "High' side. (See "SE'ITINGS".)
The sensor camera is installed too close
to the master station.
This is not a breakdown. Install the sensor camera farther from the master
station or turn the mic. sensitivity volume to the "Low" side until there is no
howling.
Sensor
\ I
4
display window
rA
Do not touch the sensor or the reflectwe
7
Operation
!
CAUTION
@There is
howling.
1
mirror.
I I
There is a dog or cat or other small
animal in the detection area.
Set the sensor sensitivity switch to "L (Low)". (See "SETTINGS".)
-
Installation precautionsA
H
For correct installation
Do not install in the following places.
Recommend to connect an external sensor and use it in "AND mode". (See
"SETTINGS'.) @The sensor is
detecting but
the detected
objects are not
displayed on the
screen.
There is something that moves in the
detection area, for example a flag or
tree
blowing in the wind, or there are sudden
temperature changes.
Set the sensor sensitivity switch to "L (Low)". (See ''SETTINGS''.)
*Either move the moving object or the object causing the sudden temperature
changes outside the detection area or change the area setting. (See
"SETTINGS'.)
\
The external sensor area does not match
the camera angle of view.
.Align the external sensor area and the camera angle of view. (See
"ADJUSTMENTS' and "SETTINGS".)
Model No. JDW-C
The wiring is incorrect or a line is open or
shorted.
Check the wiring and wire correctly. (See "MOUNTING AND
CONNECTION'.)
@The picture is
dark, blurred, or
not displayed at
all.
Power SuDDlied from the master station
The camera window is dirtv. Clean the lens with lens cleaner or with a clean, soft, damD cloth.
Any place blown on by a fan, the
outdoor unit of an &-conditioner,
or any other place subject to
sudden temperature changes.
4ny place where sunlight gets in
he angle of view of the sensor
:amera directly or indirectly.
4ny place too close to
luorescent lamps or directly
'acing powerful illumination.
Any unstable place subject to
vibration or mechanical shock.
-10
-
+50 "C Operating temperature range
Storage temperature range
Operating humidity range
The outside temperature dropped
suddenly and the camera window has
fogged up.
When the temperatures inside and outside the product even out, the camera
window returns to normal.
-20
-
+60 "C
85% (max.)
@There are white
lines on the
screen.
@The screen is
t
flickering.
Picture element 1/3-inch color CCD
There is a bright light source in the
camera angle of view.
*Either remove the light source, adjust the angle so that the light does not come
into the angle of view, or change the mounting location of the main unit. (See
"ADJUSTMENTS".)
/
Camera anale of view (horizontal x vertical) 71 5" x 53.4" (f=3.8)
Minimum illumination 1
.o
lux
There is a fluorescent lamp nearby. This is not a breakdown. Block out the light from the fluorescent lamp.
Sensor operation display light
Sensor detection method
Sensor detection area
Lights up green when the sensor detects something (Can be switched OFF with the select switch)
Heat ray type
Max. 5 meters, approx. 70"
Sensor detection speed 0.3
-
1.5 mlsec.
Sensor sensitivitv switchina Switchable among three levels H (high), M (medium), and L (low)
Amrox. 30 sec. after Dower comes on Sensor startuD time
On any surface that moves or is
affected by wind.
In or near any place subject to
steam or oil from an exhaust
duct.
External sensor input
Internal sensor switching
An external sensor can be connected and operated in either an "AND" or "OR" configuration with this unit.
The internal body detection sensor can be controlled to be "ON" or "OFF".
Aiphone warrants its products to be free from defects of material and workmanship under normal use and service for a period of
two years after delivery to the ultimate user and will repair free of charge or replace at no charge, should it become defective upon
which examination shall disclose to be defective and under warranty. Aiphone reserves unto itself the sole right to make the final
decision whether there is a defect in materials and/or workmanship; and whether or not the product is within the warranty. This
warranty shall not apply to any Aiphone product which has been subject to misuse, neglect, accident, or to use in violation of
instructions furnished, nor extended to units which have been repaired or altered outside of the factory. This warranty does not
cover batteries or damage caused by batteries used in connection with the unit. This warranty covers bench repairs only, and any
repairs must be made at the shop or place designated in writing by Aiphone. Aiphone will not be responsible for any costs incurred
involving on site service calls.
Internal speaker The internal speaker can be controlled to be "ON" or "OFF" with the speaker select switch.
Internal mic. The mic. sensitivitv can be adiusted with the mic. sensitivitv volume.
Master station switch Switchable accordina to the master station version.
- Connection precautionsA
.Use two conductor wire from the JDW-C to the master station. Do not use coaxial cable.
.When using two cameras, always use one two conductor wire for each camera. If you connect two cameras with one multi-
conductor wire, the cameras may not operate correctly.
@If
the wiring is routed together with high voltage AC wiring, other power wiring, wiring for electrical lights, and telephone
lines, this can disrupt the picture and sound quality and cause malfunction. Either use separate conduits or run wires in
separate paths from each other.
.When existing wiring is used, for some type of wiring, this system may not operate correctly. Changing the wiring restores
normal operation.
k50" leftlright, -20" to -55" up/down (The horizontal direction is O".)
(The IeWright and up/down angles can both be changed in increments of 5".)
Camera
Sensor
Angle adjustment range
k50" leftlright, -20" to -55" up/down (The horizontal direction is
OO.)
(The left/riaht angle can be changed in increments of 10" and the uddown angle in increments of
5 O . I
Installation Dlaces Indoors/Outdoors
Weather-resistant Protective structure
Weight
Dimensions (mm)
Approx. 400 g
102 (W) x 182 (H) x 94 (D)