Related Manuals for Compaq 7020
Summary of Contents for Compaq 7020
- Page 1 User’s Guide Compaq 7020 Flat Panel Monitor Document Part Number: 254041-003 April 2002 Enhanced for accessibility...
- Page 2 All other product names mentioned herein may be trademarks of their respective companies. Compaq shall not be liable for technical or editorial errors or omissions contained herein. The information in this document is provided “as is” without warranty of any kind and is subject to change without notice. The warranties for Compaq products are set forth in the express limited warranty statements accompanying such products.
-
Page 3: Installation
1.5M Stereo Jack Audio Cable (speaker models only) 1.8M Power Cord AC Adapter User’s Guide If you find that any of these items is missing or appears damaged, contact your dealer immediately. Compaq 7020 Flat Panel Monitor User’s Guide Installation... -
Page 4: Viewing Angle Adjustment
Top (-5°~ +35°) & Left / Right (-45° to +45°). Figure 1-1 Do not force the monitor over its maximum CAUTION: viewing angle settings as stated above. Attempting this will result in damaging the monitor and monitor stand. Compaq 7020 Flat Panel Monitor User’s Guide... - Page 5 1. Remove the rear panel 2. Remove the rear support panel support column. 3. Unscrew screws Figure 1-2 Compaq 7020 Flat Panel Monitor User’s Guide from the monitor. (see Fig. 1-2) from the swivel base the swivel base support column Installation...
- Page 6 5 mm access holes in the plastic covering as illustrated in Figure 1-3. These specifications meet the VESA Flat Panel Monitor Physical Mounting Interface Standard (paragraphs 2.1 and 2.1.3, version 1, dated 13 November 1997). Figure 1-3 Compaq 7020 Flat Panel Monitor User’s Guide...
-
Page 7: Cable Installation
3. Place the signal cable, the DC power cable and the audio cable into their correct respective grooves Figure 1-4 Compaq 7020 Flat Panel Monitor User’s Guide from the rear of the monitor. from the swivel base Installation... -
Page 8: Connecting The Display To Your Computer
FCC regulations. A ferrite-core interface cable is included in the monitor package. This device will not be in compliance with FCC regulations when a non-ferrite-core video cable is used. Compaq 7020 Flat Panel Monitor User’s Guide... -
Page 9: Connecting The Ac Power
AC Adapter and the electrical wall outlet for adding protection against power surges to prevent the effects of sudden voltage variations from reaching the monitor. Sudden power surges may damage your monitor. Compaq 7020 Flat Panel Monitor User’s Guide Installation... -
Page 10: Connecting The Audio Cable
PC's audio card or to the front panel's "AUDIO OUT" jack of your CD ROM drive. (See Fig. 1-7) 2. Connect the other end of the audio cable to the monitor's " LINE IN " jack. Figure 1-7 Compaq 7020 Flat Panel Monitor User’s Guide... -
Page 11: Setting Up The Monitor
Power Management System The monitor supports one low power mode. When the monitor is in the low power mode, the monitor screen will be blank and the power LED indicator will light amber. Compaq 7020 Flat Panel Monitor User’s Guide Installation... -
Page 12: Display Controls
External Headphone Jack (speaker models only) Menu Button Adjustment Control Buttons Compaq 7020 Flat Panel Monitor User’s Guide Display Controls PC Audio Stereo output. The monitor speakers will be disabled when using an external headphone or external speakers. Press the menu button to view the OSD (On Screen Display) menu selection. -
Page 13: Adjusting The Monitor's Display
“Power Saving Mode”. LED is off - Power is OFF. Press the power switch to switch the monitor ON/OFF. Increase Volume - Turn the knob clockwise. Decrease Volume - Turn the knob counter clockwise. Compaq 7020 Flat Panel Monitor User’s Guide... -
Page 14: Osd Menu
Save and Return Language Deutsch English Espanol Francais Italiano Nederlands Cancel Save and Return Compaq 7020 Flat Panel Monitor User’s Guide Advanced Menu Display Controls Menu Level 3 Adjustment Message Adjustment Scale Adjustment Scale Adjustment Scale Adjustment Scale Custom Color Adjustment... - Page 15 Vertical OSD Position OSD Timeout OSD Transparency Cancel Save and Return Factory Reset Exit Advanced Menu Compaq 7020 Flat Panel Monitor User’s Guide Menu Level 3 On/Off Selection On/Off Selection On/Off Selection Display serial number Timer Set Menu Adjustment Scale...
- Page 16 Basic Main Menu: To display the Basic Main Menu, press the Menu button on the monitor front panel. Advanced Main Menu: Select “Advanced Menu” from the Basic Main Menu to display the Advanced Main Menu shown below. Compaq 7020 Flat Panel Monitor User’s Guide Display Controls...
-
Page 17: Energy Saver Feature
Upon detecting the absence of these signals, the monitor screen is blanked, the backlight is turned off, and the Power LED is turned Compaq 7020 Flat Panel Monitor User’s Guide... - Page 18 Sleep Less than 5 watts Programmable Less than 5 watts Sleep Compaq 7020 Flat Panel Monitor User’s Guide Power Usage ON = Normal operation Power LED is green Monitor screen is blanked. Backlights are turned off. Power LED turns amber.
-
Page 19: Technical Information
Input Signal Input Impedance Polarity Amplitude Multi-mode Supported Dimension (W x H x D) Weight Compaq 7020 Flat Panel Monitor User’s Guide Technical Information 17.0” (43 cm) Active matrix color TFT LCD 1280 x 1024 1280 x (RGB) x 1024 337.92 x 207.34 (HxV) -
Page 20: Preset Display Modes
70.087 37.879 60.317 48.077 72.188 49.726 74.551 48.363 60.004 56.476 70.069 60.023 75.029 68.68 75.06 71.71 76.05 Compaq 7020 Flat Panel Monitor User’s Guide Pixel (Hz) Clock (MHz) 25.175 31.500 31.500 28.322 40.000 50.000 57.284 65.000 75.000 78.750 100.000 105.561 Sync. - Page 21 Signal out of Range” message for five seconds. You should adjust the monitor’s display setting to one of the preset modes in the table above for proper screen display. Compaq 7020 Flat Panel Monitor User’s Guide H. Freq. V. Freq.
- Page 22 Green Video/Sync on Green Blue Video Open Return Red GND Green GND Blue GND +5V (for cable detect) Sync GND Open Bidirectional DDC Data (SDA) H. Sync. V. Sync. DDC Data Clock (SCL) Compaq 7020 Flat Panel Monitor User’s Guide...
- Page 23 Pin Assignment - Digital DVI-D Connector Description TX2- TX2+ Shield 2/4 TX4- Compaq 7020 Flat Panel Monitor User’s Guide Technical Information...
- Page 24 Pin Assignment - Digital DVI-D Connector TX4+ DDC Clk DDC Data TX1- TX1+ Shield 1/3 TX3- TX3+ TXO- TXO+ Shield 0/5 TX 5- TX 5+ TX CLK SHLD TX CLK + TX CLK - Compaq 7020 Flat Panel Monitor User’s Guide...
-
Page 25: Troubleshooting
3. Move to "Phase" function in OSD menu again and adjust the monitor screen to its most clear display. 4. Click "No" on "Shut Down Windows" and back to the normal PC operating environment. Compaq 7020 Flat Panel Monitor User’s Guide Troubleshooting... - Page 26 Choose a mode that is supported by your monitor. Also, if the signal cable is not connected to monitor at all or properly, the monitor screen will display a message "No Input Signal". Compaq 7020 Flat Panel Monitor User’s Guide...
-
Page 27: Agency Regulatory Notices
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Compaq Computer Corporation may void the user's authority to operate the equipment. Compaq 7020 Flat Panel Monitor User’s Guide... -
Page 28: Declaration Of Conformity For Products Marked With Fcc Logo, United States Only
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Avis Canadien Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Compaq 7020 Flat Panel Monitor User’s Guide... -
Page 29: Epa Energy Star Compliance
Monitors that are marked with the Energy Star Logo meet the requirements of the EPA Energy Star program. As an Energy Star Partner, Compaq Computer Corporation has determined that this product meets the Energy Star guidelines for energy efficiency. Specific details on using the Energy Saving features can be found in the energy saver or power management section of the computer manual. -
Page 30: Power Cord Set Requirements
18AWG, and the length of the cord must be between 6 feet (1.8 m) and 12 feet (3.6 m). If you have questions about the type of power cord to use, contact your Compaq authorized service provider. A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it. - Page 31 Since it is not so far possible to satisfactorily recycle the majority of electronics equipment, most of these potentially damaging substances sooner or later enter nature. Compaq 7020 Flat Panel Monitor User’s Guide...
- Page 32 Labelled products must meet strict environmental demands, for example, in respect of the reduction of electric and magnetic fields, physical and visual ergonomics and good usability. Compaq 7020 Flat Panel Monitor User’s Guide...
-
Page 33: Environmental Requirements
The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available. Compaq 7020 Flat Panel Monitor User’s Guide TCO ‘99... - Page 34 CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a consequence. Compaq 7020 Flat Panel Monitor User’s Guide...
- Page 35 *Bioaccumulative is defined as substances which accumulate within living organisms. **Lead, Cadmium and Mercury are heavy metals that are Bioaccumulative. Compaq 7020 Flat Panel Monitor User’s Guide TCO ‘99...