Muse M-57 BT - Micro System Cd/Mp3 With Bluetooth Manual

Please read the instruction carefully before operating

LOCATION OF CONTROLS

1. LED display
2. Standby indicator
3. Remote sensor
4. Play/Pause button
5. Standby button
6. button: Stop; Auto scan and memorizing
7. source button
8. , buttons: Skip/search /Tuning
9. VOL+/- knob
10. LINE IN jack (Aux in)
11. USB port
12. Disc door open button
13. Disc compartment
14. FM antenna
15. AC cord
16. Speaker terminal
17. Speaker box
18. Speaker wire

REMOTE CONTROL

R1. Standby button
R2. MUTE button
R3. 0-9,10+ number buttons
R4. PROG button: To program playback sequences.
R5. ALB-/+ buttons: Folder down /up
R6. VOL-/+ button
R7. / /M- (memory -) button: Skip/search / preset down
R8. / / M+ (memory +) button: Skip/search / preset up
R9. Play/Pause button
R10. TUN-/+ buttons: Tuning
R11. CD button
R12. USB button
R13. FM button
R14. SOURCE button
R15. INTRO button
R16. REPEAT button
R17. RANDOM button
R18. AUTO/STOP button
R19. SLEEP button
R20. EQ button
R21. MEMORY button
R22. ST/MONO button

INSTALLING BATTERY

Insert 2 "AAA/ UM4" batteries to the remote control prior to use. Make sure to match their polarities (+/-) to the markings inside the compartment.

Before throwing any batteries away, consult your distributor who may be able to take them back for specific recycling.

NOTES:

• Never recharge the batteries, apply heat to them or take them apart.
• If the remote control is not going to be used for a long time, remove the battery to avoid damage caused by battery leakage corrosion.
• Attention should be drawn to the environmental aspects of battery disposal.
• Do not throw batteries in fire!
• Battery shall not be exposed to excessive heat such as sunshine, fire or the like.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

SPEAKER CONNECTION

1. Insert the speaker wires by pushing down the terminal lever of the Left Speaker Terminal and the Right Speaker Terminal.
2. Connect the speaker to Speaker Terminals, with BLACK wire to BLACK terminals and WHITE/BLACK wire to WHITE terminals.
   Push Speaker terminal tab down to insert wire.
   
   Release tab to lock wire in the terminal.
   

POWER SUPPLY

This set operates on AC 100-240V ~ 50/60Hz. Connect the power cord to a convenient AC wall outlet.

AUDIO CONTROLS

1. Press STANDBY button to turn on the unit.
2. The function (CD/ USB/ FM/ LINE IN/ BLUETOOTH) is selected by pressing or SOURCE button repeatedly, or pressing CD, USB or FM button on remote control respectively.

Note: In a concern of saving energy, when playback has reached to the end or listening volume is set at a very low level and no control is operated on the device for a period of 2 hours, the unit will automatically switch to Standby mode.

VOLUME

Turn VOL+/- control to adjust the sound to comfortable level. The volume level will be displayed for a few seconds.

MUTE

To cut off the sound from the speakers temporarily, press MUTE button on remote control. The "MUTE" icon is shown on the display. Press MUTE button again to cancel Mute mode and restore the sound from the speakers.

EQ

Press EQ button on remote control to toggle among the different sound effects (FLAT / POP / ROC (ROCK) /JAZZ /CLASSIC). The selection will show on display for few seconds.

DISC OPERATION

1. Press STANDBY button to turn on the unit.
2. Open the CD door by pushing the CD door Open button .
3. Place the CD with label side up inside the CD compartment and close the CD door.
4. Press , SOURCE or CD button to select CD function. After a few seconds, the total number of track and total play time will appear on display. The "CD" icon is displayed. Playback starts automatically.

BASIC OPERATION

PLAY/PAUSE

To temporarily stop playing, press button. To resume play, press this button again.

STOP

If the button is pressed in the course of playing, the disc will cease to play. (Total number of tracks will show on display).

Select a track

• By /
  Press / to select a track.
• By number buttons 10+, 0-9
  Use the number buttons to input the track number, and it will start playback from the selected track automatically.
  If you want to input the track number bigger than 9, use the 10+, 0-9 button.
  Example 1, to select the 10th track:
  Method 1: Press 10+ button once, "01-" will blink on display for 2 seconds and playback starts automatically.
  Method 2: Press 1 and then 0. "010" will blink on display for 2 seconds and playback starts automatically.
  Example 2, to select the 25th track:
  Method 1: Press 10+ button twice, "02-" blinks on display, then press 5 button when "02-" is blinking. After that, "025" will blink on display for 2 seconds and playback starts automatically.
  Method 2: Press 2 and then 5. "025" will blink on display for 2 seconds and playback starts automatically.

Fast search backward/forward

Press and hold / to search quickly within a track.

Select a folder (mp3 only)

• Press ALB+ on remote control to select the first track of next folder of your current disc or USB.
• Press ALB- on remote control to select the first track of previous folder of your current disc or USB.

USB OPERATION

USB PLAYBACK

1. Press STANDBY button to turn on the unit.
2. Connect an USB device to the USB port on unit.
3. Press , SOURCE or USB button to select USB mode. After a few seconds, the total number of folder and track will appear on display. Playback starts automatically.

Notes:

• The total number of MP3 files on the USB device should not exceed 999.
• The device may not contain more than 99 directories.
• The reading time takes about a few seconds or more depending on the amount of MP3 files and folders on USB device.
• Do not put anything other than a USB device to the port of this unit. Other objects may damage the USB mechanism.
• The USB socket must not be connected to the computer directly, for that may damage the unit.
• There are many USB devices in the market. We cannot guarantee to support all different models. Please try another USB device if your device is not supported.

USB CHARGING

This unit is equipped with a built-in USB charging port (Output: 5V 300mA) for recharging your mobile device (e.g. Smart phone, tablet, etc.) Simply plug the USB charging cable (not included) into the USB charging port and connect it to your mobile device.

Note:
The charging time of mobile device will vary depending on factors such as temperature or battery capacity.

RADIO

Listening to the radio

1. Press STANDBY button to turn on the unit.
2. Press , SOURCE or FM button to select FM Radio mode. "FM" appears on display.
3. Tune to a desired station with / on unit or TUN-/+ on remote control.

Note:

• For a better reception in FM, extend the antenna.
• If a stereo broadcast is received, "ST" is displayed. Press ST/MONO button on remote control to switch between Mono and Stereo mode.

Presetting radio stations

The unit can store up to 30 FM stations in its memory.

Manual preset

1. Tune to a desired station.
2. Press MEMORY button on remote control. "" flashes on display.
3. Press M-/+ on remote control to select a desired preset location. Press MEMORY again to save the radio station as the selected preset station.
4. Repeat above steps to preset a maximum of 30 stations.

Auto preset

In FM mode, hold and press AUTO to start automatic preset programming.
Radio frequencies will be browsed and radio stations stored automatically. When all the available radio stations are stored or all memory locations are full, the auto preset programming function will stop.

Retrieving the preset stations

In radio mode, press M-/+ on remote control to access a preset station.

PLAY MODES (CD/MP3 ONLY)

Intro playback

Press INTRO button on remote control and "INTRO" appears on display. It will start to play the first 10 seconds of each track. Press INTRO button again to cancel this function and "INTRO" disappears on display.

Repeat playback

Press REPEAT button on remote control repeatedly to a play mode:

• Repeat One: display shows "REP".
• Repeat folder: display shows "REP ALB" (MP3 only).
• Repeat All: display shows "REP ALL".

To cancel repeat playback, press REPEAT button repeatedly until repeat indicator disappears.

Random playback

Press RANDOM button on remote control and "RND" appears on display. It will play all tracks in random order. Press RANDOM button again to cancel this function and "RND" disappears on display.

Program playback

1. In stop mode, press PROG button on remote control. The display will show "00 P01" ("000 P01" for MP3).
2. Use number buttons to input the track number and press PROG button to conform.
3. Repeat above steps to program up to 20 tracks for CD and 99 tracks for MP3.
4. Press to start program playback.
5. Press STOP / to stop the program playback and cancel this function.

BLUETOOTH FUNCTION

1. Press or SOURCE button repeatedly to select Bluetooth mode. "" is displayed.
2. On the Bluetooth device, enable Bluetooth and select "M-57BT" from the Device List. (Refer to the user manual of the device to be connected for detailed operations.) If the Bluetooth device prompts for a passcode, use "0000". Some Bluetooth devices will ask you to accept the connection. "" appears when pairing is successful.

Tip: If you want to connect your Bluetooth speaker to another Bluetooth audio device, you need to disconnect current device first and follow the steps above to make a new connection.

If the pairing fails, perform the following:
Press and hold the button until "" displays to enter the Pairing mode. On the Bluetooth device, enable Bluetooth and select " M-57BT " from the Device List (see step 2 above).

• On some devices such as computers, once paired you must select the unit from the Bluetooth menu and choose "Use as Audio Device (stereo)" or similar.
• Pairing remains intact when the unit and/or your Bluetooth device is taken out of communication range. An active connection will be re-established when your Bluetooth device returns within range.
• When the unit is turned on again, it will automatically try to reconnect with the most recently paired Bluetooth device.

Using a Bluetooth Device

1. With a unit paired (see previous section), operate your Bluetooth device and its sound will be heard through the M-57 BT's speakers.
2. Press the button to pause playback. Press again to resume playback.
3. Select desired track with / .
4. Adjust the volume using the Volume buttons. You can also adjust the volume on the device to which you are paired.

CONNECTING AUXILIARY SOURCE

1. Connect your auxiliary source (e.g. mp3 player) to the LINE IN jack. (Cable not included).
2. Press or SOURCE repeatedly to select Line in mode. The display will show "LINE IN".
3. Start playback from your auxiliary source.
4. Adjust the volume to desired level.
5. To stop playback, disconnect your auxiliary source from the LINE IN jack.

SLEEP FUNCTION

In sleep mode, the unit will turn off automatically after a specified time.

You can select duration in minutes before the unit turns off automatically.

1. Press SLEEP button on remote control repeatedly to select 90-80-70-60-50-40-30-20-10- 00. Release SLEEP button. "SL" icon remains on display.
   Notes:
   • Sleep time can only be set when the unit is turned ON.
   • The sleep function is cancelled when "00" is selected, and "SL" icon disappears.
2. If you want to switch off the radio before sleep ends, press STANDBY button.

MAINTENANCE

Cleaning

Disconnect the unit from the mains supply before cleaning.

• Use a soft, dry, clean cloth. Regularly dust the vents at the back or sides.
• Using solvents, abrasive or alcohol-based products risks damaging the appliance.
• If an object or liquid enters inside the appliance, unplug it immediately and have it checked by an authorized engineer.

Notes on disc

• Do not use irregular shape CDs (example: heart-shaped, octagonal ones). It may result in malfunctions.
• Do not place more than one disc in the disc compartment.
• Do not try to open the disc compartment during playing.
• Do not touch the lens. Doing so may cause malfunction.
• If there is a scratch, dirt or fingerprints on the disc, it may cause tracking error. Before playing, clean the disc with a cleaning cloth. Wipe the disc from the center out. Don't store discs in places with high temperatures or high humidity, they can become warped. After playing, store the disc in its case.
• CD-Rs or CD-RWs playback capability at this player may vary depending on quality of media, CD-Burner, speed of burning and application software.

• Before transporting the unit, remove the disc from the disc compartment.

SPECIFICATION

Power supply: AC 100-240V ~ 50/60Hz
Power consumption: 10W
Speaker: 4 ohms
Radio: FM 87.5-108MHz
Bluetooth: 2.402-2.48GHz
RF Output Power: -1.53 dBm

MORE INFORMATION

To reduce the risk of electric shock, do not remove the cover (or back). There are no user serviceable parts inside the unit. Refer all servicing to qualify personnel.

The lightening flash with arrowhead symbol within the triangle is a warning sign alerting the user of "dangerous voltage" inside the unit.

The exclamation point within the triangle is a warning sign alerting the user of important instructions accompanying the product.

The caution mark is located on back of the device.

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

Invisible laser radiation when open and interlocks defeated. Avoid exposure to beam.

This compact disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT marking is located on the bottom cabinet.

• The use of apparatus in moderate climates.
• The Marking plate is located at the back of the device.
• Make sure to have a minimum distance of 5 cm around the unit for sufficient ventilation.
• Ensure that the ventilation openings are not covered with items such as newspapers, tablecloths, curtains, etc.
• No naked flame sources, such as lighted candles, should be placed on the apparatus.
• Do not expose this appliance to dripping or splashing water.
• Do not place objects filled with liquids, such as glass, vases on the device.
• Do not throw batteries into fire! Respect the environment when disposing of used batteries.
• Batteries should not be exposed to excessive heat such as sunshine, fire or other similar heat source.
• The power plug is used as a disconnect device and must be easily accessible. To be completely disconnected from the power, the plug of the appliance should be disconnected completely. The socket must not be obstructed and should be easily accessible during intended use.
• Under the influence of fast transient and / or electrostatic electric phenomenon, the product may malfunction and the user must perform a power reset of the device.

If in the future, you need to get rid of this product, please note that Waste electrical products should not be disposed of with household waste. Recycling facilities exist. Check with your municipality or ask your dealer for advice. (Directive for Waste Electrical and Electronic Equipment)

Note: Design and specification are subject to change without notice.

The Bluetooth^® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by New One S.A.S is under license. Other trademarks and trade names are those of their respective owners.

Hereby, NEW ONE S.A.S, declares that this MUSE M-57 BT is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at http://www.muse-europe.com/conformity/M-57BT.pdf

NEW ONE S.A.S
10, Rue de la Mission, 25480 Ecole Valentin, France