Pioneer DDJ-SP1 Operating Instructions Manual page 22

Dj controller
Hide thumbs Also See for DDJ-SP1:
Table of Contents

Advertisement

4 Press the rotary selector.
This saves the parameters that have been set in this unit's memory.
While the parameters are being saved, the eight buttons in the effect
section flash. Do not disconnect the USB cable from this unit during this
time.
5 Press the [BACK] button.
This unit switches from the utilities mode back to normal operation.
Changing the setting of the illumination
when tracks are loaded
The pattern with which the illumination lights when tracks are loaded
can be switched.
! By default, illumination type 1 is set.
1 Press the [BACK] button for over 1 second to switch
to the utilities mode.
2 Turn the rotary selector so that the FX2 effect
parameter 3 button flashes.
1
1
3
2
2
4
ON
SELECT
3
4
3 Press pad 1 or pad 2 on the left performance pads.
The currently set value is indicated by which pads are flashing.
! Pad 1 flashing: Illumination type 1 selected
! Pad 2 flashing: Illumination type 2 selected
4 Press the rotary selector.
This saves the parameters that have been set in this unit's memory.
While the parameters are being saved, the eight buttons in the effect
section flash. Do not disconnect the USB cable from this unit during this
time.
5 Press the [BACK] button.
This unit switches from the utilities mode back to normal operation.
Enabling the advanced MIDI setting
The advanced MIDI function will be used with future feature enhance-
ments to the Serato DJ software. When the advanced MIDI function
is enabled, the effect parameter controls, [FX BEATS] control, effect
parameter buttons and [TAP] button switch to special MIDI codes when
this unit's [AUTO LOOP] control is pressed while pressing the [SHIFT]
button.
! By default, the advanced MIDI setting is disabled.
! To control Serato Video with this unit, disable the advanced MIDI
setting.
Buttons and controls to which advanced MIDI settings
are applied
ON
ON
ON
TAP
FX
FX
FX
SELECT
SELECT
SELECT
AUTO LOOP
SLIP
CENSOR
PARAM.1
SYNC
OFF
REL.
INT.
PARAM.2
HOT CUE
ROLL
SLICER
HOT LOOP
AUTO LOOP
MANUAL LOOP
LOOP ACTIVE
SAVE
SLOT
IN
OUT
RELOOP / EXIT
SLOT
22
En
ON
ON
TAP
FX
FX
FX
SELECT
SELECT
1
1
3
2
2
4
ON
ON
ON
FX
FX
FX
MODE
3
4
SELECT
SELECT
PANEL SELECT
SLIP
CENSOR
SYNC
OFF
REL.
INT.
• BACK
LOAD
— UTILITY
PREPARE
SAMPLER
HOT CUE
ROLL
VELOCITY
VIEW
AREA
HOT LOOP
AUTO LOOP
LOOP ACTIVE
SAVE
LOAD
LOAD
SHIFT
IN
OUT
RELOOP / EXIT
SAMPLER VOL
DJ CONTROLLER
1 Press the [BACK] button for over 1 second to switch
to the utilities mode.
2 Turn the rotary selector so that the FX2 [TAP] button
flashes.
1
2
3
3 Press pad 1 or pad 2 on the left performance pads.
! Pad 1 flashing: Advanced MIDI settings disabled
! Pad 2 flashing: Advanced MIDI settings enabled
4 Press the rotary selector.
This saves the parameters that have been set in this unit's memory.
While the parameters are being saved, the eight buttons in the effect
section flash. Do not disconnect the USB cable from this unit during this
time.
5 Press the [BACK] button.
This unit switches from the utilities mode back to normal operation.
FX
MODE
TAP
FX
FX
SELECT
MODE
AUTO LOOP
PARAM.1
PARAM.2
SLICER
SAMPLER
MANUAL LOOP
VELOCITY
SLOT
SLOT
DDJ-SP1
1
3
2
4
ON
ON
FX
FX
4
SELECT
SELECT
ON
TAP
FX
FX
SELECT
MODE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DDJ-SP1 and is the answer not in the manual?

Questions and answers

Table of Contents