Installation; Specifications; Technical Data - Nakayama NP1010 Manual

EN
SAFETY INSTRUCTIONS
Note: After opening the package, please ensure that no parts are missing or damaged. If parts are missing or damaged, do not use the machine and send it
back to your dealer.
Important: This manual must always accompany the equipment upon its resale.
• To ensure proper and safe operation of this equipment, the operator must read and understand these instructions before first use.
• This manual should be kept close in a safe spot and be made available to all operators of this machine.
• All electrical sockets must be earthed.
• No power cord should be used for transporting or fixing the equipment.
• Don't pull the power cord on the sharp edge and don't press the power cord.
• The power supply voltage must be the same as the voltage given on the model board.
• To avoid hazards, all installation and replacement of components can only be carried out by authorized customer service personnel.
• Electrical connections can only be performed by electrical professionals, and please comply with state regulations for this.
• The pump must be connected with a current type leakage current breaker which carry a rated leakage current of no more than 30 MA.
• Check the connection of the plug before running. If the wire is damaged, it must be replaced by the manufacturer, the agent or the relevant technical
personnel to avoid any danger.
• The device is suitable for children at eight or older. People with sensory or physical disabilities or deficiencies are required to use under supervision or
knowledge of safety, use and danger. Children are not allowed to wash or maintain equipment without supervision.
• Liquid contamination may be caused by leakage of lubricating oil.
• The water pump can be connected with a shock proof plug installed in accordance with the regulations.
• Do not use pumps when there is someone in the water.
• When cleaning and maintaining, please disconnect the water pump from the main power supply.
• Please contact technical staff in the case of equipment damage.
• Connectors for power plugs and extension cables must be made sure that they are watertight and must not be placed in the water. Furthermore, connectors
cannot be placed on the ground. It is recommended to ensure that the outlet is at least 60 mm from the ground.
Attention!
Danger!
Attention!

INSTALLATION

Sufficiently long and strong ropes should be attached to the handle before first use. When the pump is immersed into the liquid, the rope along with a handle
can be used to balance the pump.
The equipment requires an area of at least 60x60cm.
Submersion depth of equipment is written in technical data.
When installing the equipment, make sure that the suction opening will not be blocked by foreign objects to keep the equipment stable.

SPECIFICATIONS

Technical Data

NP1010
Model
Nominal voltage 230V / 50Hz
Nominal Output 400W
Protection type IPX8
Max. supply height 8m
Max. conveying amount 7000 L/h
Max. submersion depth 7m
Max. grain size 5mm
2
Failure to follow these safety instructions can lead to electrical shock,
which endangers the life of the operator or of bystanders.
Do not repair the power cord if there is any external damage to the
power cord or plug. Danger of electrical shock.
Risk of equipment damage: The maximum grain size mentioned in
the technical data does not refer to gravel but to material that can be
dissolved in the pump. Suction of gravel can cause the pump to fail.
NP1020 NP1030
230V / 50Hz 230V / 50Hz
750W 550W
IPX8 IPX8
8.5m 7m
12500 L/h 10000 L/h
7m 7m
5mm 35mm
WWW.NIKOLAOUTOOLS.GR
* The manufacturer reserves the right to make minor changes to product
design and technical specifications without prior notice unless these
changes significantly affect the performance and safety of the products.
NP1060 NP1130
The parts described / illustrated in the pages of the manual that you hold
in your hands may also concern other models of the manufacturer's
product line with similar features and may not be included in the product
230V / 50Hz 230V / 50Hz
you just acquired.
1100W 1300W
* To ensure the safety and reliability of the product and the warranty
validity, all repair, inspection, repair or replacement work, including
IPX8 IPX8
maintenance and special adjustments, must only be carried out by
technicians of the authorized service department of the manufacturer.
10.5 11m
* Always use the product with the supplied equipment. Operation of the
product with non-provided equipment may cause malfunctions or even
16500 L/h 25000 L/h
serious injury or death. The manufacturer and the importer shall not be
liable for injuries and damages resulting from the use of non-conforming
7m 7m
equipment.
35mm 40mm