Motorola HDT101 Quick Setup Manual page 2

1
Connecting Component Video (YPbPr)
L R
AUDIO
Y Pb Pr
RF IN S/PDIF OUT S-VIDEO RS-232
TV
Component
Video Input
Y
Component video cable
Pb
Pr
Component video provides the highest level of picture quality. If your television has component video inputs
(Y, Pb, and Pr connectors), connect to the component video connections on your HDT101 instead of the VIDEO or
S-VIDEO connections. (To connect for S-Video or Composite Video, see the instructions in the HDT101 User Guide.)
To connect component video:
- Connect the component video cable supplied with the HDT101 to the , Y Pb , and
Now proceed to the instructions for the audio connections.
AUTO SCAN
Before you can start using the HDT101, you need to program it with the station numbers of the over-the-air digital TV stations available in
your area. This is done by simply running Auto Scan from the HDT101's on-screen menu
Navigate the on-screen menu using the remote control:
- Use the and arrow keys to move up and down the on-screen menu
- Use the SELECT button to select the highlighted item on the on-screen menu
- Use the EXIT button to return to the main menu from a submenu or to leave the main menu
To run auto scan:
1 Press POWER on the HDT101 front panel or remote control to turn on the receiver.
2 Press MENU on the remote control. The Menu screen is displayed:
3 Using the arrow key, highlight Installation and press SELECT . The Password window is displayed.
2
HDT101
VIDEO
DC IN
To connect your audio connections:
- Connect the stereo audio cable supplied with your HDT101 to the and connectors on the HDT101 and the
and connectors on your TV.
LEFT RIGHT
Once you complete your audio connections, proceed to the instructions for connecting the antenna and power cord.
Pr connectors on your TV and HDT101.
Now proceed to the next step, Connecting the Antenna and Power Cord.
4 Enter the default password:
after you have completed steps 1-3 above.
5 Highlight Auto Scan
The HDT101 starts scanning from Channels 2 to 69. The entire scan will take about four minutes. An indicator is displayed
showing the scan's progress:
Connecting Audio
HDT101
L R
AUDIO VIDEO
Y Pb Pr
RFIN S/PDIF OUT S-VIDEO RS-232 DC IN
TV
Input
Audio cable
Audio left
Audio right
L R
0000 . The Installation menu is displayed:
in the Installation menu and press SELECT .
3
Connecting the Antenna and Power Cord
RFIN S/PDIF OUT S-VIDEO
To
antenna
To receive over-the-air high definition TV signals use an outdoor or indoor antenna.
- Connect your antenna's coaxial cable to the connector on your HDT101.
RF IN
INPUT AUDIO
- Plug the power cord supplied with your HDT101 into the HDT101's power connector and then plug the cord into a wall outlet.
Now that you've completed hooking up your HDT101, log on to the
digital TV stations in your area and view instructions for positioning your antenna:
After visiting the website, proceed to "Auto Scan" below to program your HDT101 with over-the-air digital TV stations.
As each digital TV signal is scanned, you'll see the signal's channel number and program name displayed
on the Program List:
The auto scan will end on channel 69.
6 Press EXIT to return to the main menu.
7 Press EXIT again to exit the main menu and start enjoying digital TV programs!
If the picture displayed on your TV is too small, use the A. RATIO
to change the picture size. Use the V. FORMAT button to select the desired Video Format to match your TV.
If you have questions, see the HDT101 User Guide or contact the Motorola Customer Support Center at
1-866-668-2271 or 1-866-MOT-BCS1.
HDT101
L R
AUDIO VIDEO
Y Pb Pr
RS-232 DCIN
To
power
supply
http://www.antennaweb.org/ website to find the
(Aspect Ratio) button on your remote control