CommScope RUCKUS SmartZone 300 Quick Setup Manual

RUCKUS SmartZone 300
Spare Solid State Drive
Quick Setup Guide
This Quick Setup Guide provides basic instructions for ordering
and installing a spare solid state drive (SSD) into the Ruckus
SmartZone 300 (SZ300) controller.
For information on advanced configuration and management
options, see the Getting Started Guide and other appropriate
documents, which are available for download from the Ruckus
Support website:
https://support.ruckuswireless.com/documents.
This Guide in Other Languages
请从以下网站获得该指南的简体中文版
https://
support.ruckuswireless.com.
Vous trouverez la version française de ce guide à l'adresse
suivante https://support.ruckuswireless.com.
このガイドの日本語版は
https://support.ruckuswireless.com
でご覧ください。
이 가이드의 한국어 버전은 웹 사이트
(https://
support.ruckuswireless.com) 에서 확인하시기 바랍니다.
Veja a versão em português (Brasil) deste guia em
support.ruckuswireless.com.
Puede ver la versión en español (América Latina) de esta guía en
https://support.ruckuswireless.com.
Solid State Drive Ordering Information
To order a spare solid state drive (SSD) for the SmartZone 300
controller, contact Ruckus Support.
For information on how to contact Ruckus Support, visit
support.ruckuswireless.com/contact-us. When asked for the part
number, provide the information in the following table.
Part Number Description
902-S351-0000 Kit, Spare (FRU), solid state disk 64KB, SZ300
Copyright © 2021 CommScope, Inc. All rights reserved.
Published December 2021, Part Number 800-72229-001 Rev D
Opening the Front Bezel
The front bezel helps prevent accidental access to the controller's
modules. Before you can install a module, you must open the
front bezel.
NOTE: If the controller is mounted in a rack with adjacent units
below the unit where a module needs to be serviced, Ruckus
recommends extracting the controller from the rack
approximately 5cm (2 in.). This will provide clearance of the
bezel when rotated out towards you.
Follow these steps to open the front bezel.
1. With the controller in front of you, place your fingers on both
sides of the front bezel.
2. Pull the bezel toward you until it opens.
3. Gently lower the bezel to expose the controller's replaceable
modules.
FIGURE 1 Controller with the front bezel open
https://
Installing a Spare SSD
After you have obtained a spare solid state drive (SSD) and
opened the front bezel of the SmartZone 300 controller, you are
ready to install the SSD.
ATTENTION-QSG: Unlike the two hard disk drives (HDDs) in the
controller, the single SSD is neither redundant nor hot-
https:// swappable.
Follow these steps to install the SSD.
1. On the controller, run the shutdown command from the CLI.
device# shutdown
2. When the controller has completely powered down, locate
the SSD tray on the front panel. From the top of the front
panel, disk tray 1 is for the SSD, and disk trays 2 and 3 are for
hard disk drives (HDDs) (see the following figure).
NOTE: Tray 4 is unused.
FIGURE 2 Disk trays on the front panel of the controller
NOTE: If you are replacing a failed disk, check the LED of
each tray. A red or amber LED indicates that the disk is not
operational.
3. Unlock the disk tray by moving the orange disk tray lock to
the left (unlock) position.
4. Press the black/blue tray button to open the tray handle.
Page 1 of 2