Download  Print this page

Programming The Remote Control - Mitsubishi Electric WD-60737 Owner's Manual

C9 series 737 series 837 series home theater television.
Hide thumbs

Advertisement

Appendix A: Programming the Remote Control, continued

Programming the Remote Control

1.
Press the side button on the remote control to
change to the correct mode for the product you
want to control. Refer to the table below. Only
one of each device type can be controlled in each
mode.
Mode
Affected Device
CABLE/SAT
Cable Box
DTV Receiver
Satellite Receiver
VCR
VCR
DVR
DVD Player/Recorder
DVD
DVD Player/Recorder
DVR
VCR
AUDIO
A/V Receiver
Audio Amplifier
CD Player
2.
Press and hold
POWER on the remote control for
several seconds until the mode indicator blinks
twice and goes off.
3.
Release the
POWER key.
4.
Enter the first five-digit code listed for your equip-
ment.
The mode indicator blinks twice when you
start to enter the code and then once for each
additional keypress.
The mode indicator blinks twice when you finish
entering a valid code.
If you need to start over or wish to exit pro-
gramming mode, temporarily change to a
different mode using the side button.
5.
Point the remote control at the equipment and
press POWER. If the product has no power on/off
function, press a different key, such as
(STOP), VOLUME UP, or MUTE.
If the equipment responds, the remote control
is properly programmed.
If the equipment does not respond, repeat
steps 2–4 with the next five-digit code listed for
your equipment.
6.
Once you have found the correct code, write it in
the space below for future reference.
Mode
CABLE/SAT
VCR
DVD
AUDIO
You may need to reprogram the remote control after
changing the batteries. Record the codes for each
mode in the space provided to make this faster.
Code Verification
To determine the code programmed for any mode:
1.
Set the mode to the one you wish to verify.
2.
Press and hold
several seconds until the mode indicator blinks twice
and goes off.
3.
Press keys
4.
Press
Write down the number of blinks as the first digit of
the code.
5.
Repeat step 4 for the second, third, fourth, and fifth
digits of the code.
Audio Lock: Universal A/V Receiver
Control
With Audio Lock enabled, the remote control operates
volume and mute on the A/V receiver in all modes set by
the side button. Activate Audio Lock if you normally use
an A/V receiver with your TV and other A/V equipment.
1.
Program
described in "Programming the Remote Control" on
this page.
2.
(PLAY),
With the remote control in
on the remote control for several seconds until the
mode indicator blinks twice and goes off.
3.
Press keys
The mode indicator will blink twice to indicate Audio
Lock is active.
To Reset the Remote Control to Operate Volume
and Mute for the TV Speakers
1.
Press and hold
mode indicator blinks twice and goes off.
2.
Press keys
The mode indicator will blink four times to indicate
Audio Lock has cleared.
Appendices
Device Type
IMPORTANT
POWER on the remote control for
9 9 0
1 and count the blinks of the power key.
AUDIO mode for your A/V receiver as
AUDIO mode, hold POWER
9 9 3 ENTER
POWER for several seconds until the
9 9 3 VOLUME UP.
59
Code

Advertisement

Table of Contents

   Also See for Mitsubishi Electric WD-60737

   Related Manuals for Mitsubishi Electric WD-60737

This manual is also suitable for:

Wd-60c9Wd-65737Wd-65837Wd-65c9Wd-73737Wd-73837 ... Show all

Comments to this Manuals

Symbols: 0
Latest comments:
  • Jerry Oct 17, 2016 07:38:
    My 6037 won't do turn on any experience​d about this
  • samir messaoudii Jul 13, 2016 12:33:
    I m looking for originl remote control,or setup on my android phone reote for my mitsubishi tv.
  • Judy Smith Sep 12, 2015 11:21:
    I have little white specs of light in the picture, what is this?
  • kirk smith Dec 14, 2014 03:34:
    question, can you make this tv read bluetooth or wifi signals
  • Linda Miles Jun 08, 2014 06:00:
    I have a Mitsubishi Wd-60737 it is stuck in standby mold.