Architects’ And Engineers’ Specifications - Mackie Art Series ART200A Specifications

ART200A
Two-Way Active Speaker System
Architects' and Engineers' Specifications
The amplified loudspeaker system shall be a self-con-
tained unit, housed in a reinforced polypropylene enclosure
and consisting of the following sub-systems: (1) vented two-
way loudspeaker system, (2) integrated power amplifiers and
crossover network, (3) integrated mic/line input with music
and voice equalizers.
The loudspeakers shall consist of a 12 inch low-
frequency, cone driver, and a 90° x 70° high-frequency,
constant-directivity polynomial horn with a horn-loaded, 1
inch compression driver. The drivers shall be aligned with
an analog circuit and crossed over at 1.8kHz by a 4-pole
network built into the power amplifiers. Together they shall
be capable of producing 122dB SPL (1m, anechoic).
Two discrete amplifiers shall be provided, capable of con-
tinuously delivering 120W RMS to the low-frequency driver
and 40W RMS to the high-frequency driver. Distortion shall
be less than 0.1% when measured at 1kHz and 10kHz. They
shall be equipped with a multi-function protection circuit to
peak limit and protect the loudspeakers from overheating,
over-excursion, short circuits and extreme operating temper-
atures. An indicator lamp shall illuminate when any aspect of
the protection circuit engages.
The integrated mic/line input shall be actively balanced,
may accept an unbalanced input, and shall be paralleled to
an output. Both shall have XLR connectors. The input shall
have a switch to select between 8mV mic and 125mV line
levels. The unit shall be provided with both voice and music
optimization equalization that can be activated with buttons
on the rear panel. The voice equalizer shall provide +4dB at
3kHz and 6kHz. The music equalizer shall provide +4dB at
65Hz and +4dB at 12kHz. A continuously variable, rotary
master volume control shall be provided.
The power supply shall be internal and connected to 50 or
60Hz source current through a detachable IEC power cord. It
shall have an on/off switch, fuse holder, and threaded
grounding screw on the rear panel. AC voltage shall be selec-
table between 115 and 230VAC. The power supply shall draw
a maximum of 2A and illuminate an indicator light when on.
The reinforced polypropylene enclosure shall have a vol-
ume of at least 1.65 cu. ft., be trapezoidal in shape and
equipped with a grille to protect the cone driver. At least four
M10 threaded sockets shall be molded into the cabinet for
attaching mounting hardware, designed for the unit and
www.mackieindustrial.com
16220 Wood-Red Rd. NE, Woodinville, WA 98072 USA
888.337.7404, fax 425.487.4337, industrial@mackie.com
UK +44.1268.571.212, fax +44.1268.570.809, info@rcf-uk.com
ITALY +39.0522.354.111, fax +39.0522.926.208, industrial@rcf.it
FRANCE +33.3.8546.9160, fax +33.3.8546.9161, rcf.commercial@wanadoo.fr
GERMANY +49.2572.96042.0, fax +49.2572.96042.10, industrial@mackie.de
(continued Architects' & Engineers' Specs)
available from the manufacturer. A full metal grille assembly,
covering the front of the enclosure shall be available from
the manufacturer. The amplified loudspeaker system shall be
a model ART200A manufactured by Mackie Industrial.
Electronic files for this product available at:
www.mackieindustrial.com
This Specification Sheet
Quick-Start Manual
Mackie Designs continually engages in research related to product improvement. New material, produc-
tion methods, and design refinements are introduced into existing products without notice as a routine
expression of that philosophy. For this reason, any current Mackie Industrial product may differ in some
respect from its published description, but will always equal or exceed the original design specifications
unless otherwise stated. ©1999-2001 Mackie Designs Inc. All rights Reserved.
registered trademarks of Mackie Designs Inc. Mackie Industrial is a trademark of Mackie Designs Inc.
ART200A.PDF
ART200AQS.PDF
and are
part no. 910-161-10 Rev.B
6
O F 6 P A G E S
oF 6 PAGES