TLV PowerDyne HR80A Instruction Manual
  1. Manuals
  2. Brands
  3. TLV Manuals
  4. Plumbing Product
  5. PowerDyne HR80A
  6. Instruction manual

TLV PowerDyne HR80A Instruction Manual

Thermodynamic steam trap
Hide thumbs Also See for PowerDyne HR80A:
Table of Contents

Advertisement

Quick Links

Download this manual
172-65165MA-05 (HR80A)
13 September 2021
TM
Thermodynamic Steam Trap
HR80A
Copyright © 2021 by TLV CO., LTD.
All rights reserved

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PowerDyne HR80A and is the answer not in the manual?

Questions and answers

Related Manuals for TLV PowerDyne HR80A

Summary of Contents for TLV PowerDyne HR80A

  • Page 1 172-65165MA-05 (HR80A) 13 September 2021 Thermodynamic Steam Trap HR80A Copyright © 2021 by TLV CO., LTD. All rights reserved...

  • Page 2: Table Of Contents

    If detailed instructions for special order specifications or options not contained in this manual are required, please contact TLV for full details. This instruction manual is intended for use with the model(s) listed on the front cover.

  • Page 3: Safety Considerations

    • The three types of cautionary items above are very important for safety: be sure to observe all of them as they relate to installation, use, maintenance, and repair. Furthermore, TLV accepts no responsibility for any accidents or damage occurring as a result of failure to observe these precautions.

  • Page 4: Checking The Piping

    Checking the Piping Use only under conditions in which no water hammer will occur. CAUTION The impact of water hammer may damage the product, leading to fluid discharge, which may cause burns or other injury. Check to make sure that the pipes to be connected to the product have been installed properly.

  • Page 5: Specifications

    Specifications Install properly and DO NOT use this product outside the recommended CAUTION operating pressure, temperature and other specification ranges. Improper use may result in such hazards as damage to the product or malfunctions that may lead to serious accidents. Local regulations may restrict the use of this product to below the conditions quoted.

  • Page 6: Configuration

    Configuration Name 1 Body  2 Cover  3 Module Valve Seat  4 Disc  5 Air Vent Ring (Bimetal)  6 Disc Holder Ring   7 Module Gasket (Large)   8 Module Gasket (Small)  9 Screen 10 Cover Bolt 11 Nameplate 12 Cap...

  • Page 7: Installation

    Installation Install properly and DO NOT use this product outside the recommended CAUTION operating pressure, temperature and other specification ranges. Improper use may result in such hazards as damage to the product or malfunctions that may lead to serious accidents. Local regulations may restrict the use of this product to below the conditions quoted.

  • Page 8: Maintenance

    (When conducting a visual inspection, flash steam is sometimes mistaken for steam leakage. For this reason, the use of a steam trap diagnostic instrument [TLV: TrapMan*] in conjunction with the visual inspection is highly recommended.) *For products having operating conditions compatible with Pocket TrapMan and TrapMan specifications.

  • Page 9: Disassembly/Reassembly

    Disassembly/Reassembly When disassembling or removing the product, wait until the internal CAUTION pressure equals atmospheric pressure and the surface of the product has cooled to room temperature. Disassembling or removing the product when it is hot or under pressure may lead to discharge of fluids, causing burns, other injuries or damage.
  • Page 10 Table of Tightening Torques Torque Distance Across Flats Part Name N·m (lbf·ft) (in) Cover Bolt (37) (1 N⋅m ≈ 10 kg⋅cm) NOTE: - Coat all threaded portions with anti-seize. - If drawings or other special documentation were supplied for the product, any torque given there takes precedence over values shown here.

  • Page 11: Troubleshooting

    Troubleshooting When disassembling or removing the product, wait until the internal CAUTION pressure equals atmospheric pressure and the surface of the product has cooled to room temperature. Disassembling or removing the product when it is hot or under pressure may lead to discharge of fluids, causing burns, other injuries or damage.

  • Page 12: Tlv Express Limited Warranty

    Subject to the limitations set forth below, TLV CO., LTD., a Japanese corporation (“TLV”), warrants that products which are sold by it, TLV International Inc. (“TII”) or one of its group companies excluding TLV Corporation (a corporation of the United States of America), (hereinafter the “Products”) are designed and manufactured by TLV, conform...
  • Page 13 WARRANTY NOT NEGATED HEREBY, AND ANY IMPLIED WARRANTY NOT NEGATED HEREBY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, DO NOT COVER, AND NEITHER TLV, TII NOR ITS TLV GROUP COMPANIES WILL IN ANY EVENT BE LIABLE FOR, INCIDENTAL OR...

  • Page 14: Service

    Service For Service or Technical Assistance: Contact your TLV representative or your regional TLV office. In Europe: Tel: [49]-(0)7263-9150-0 Daimler-Benz-Straße 16-18, 74915 Waibstadt, Germany Fax: [49]-(0)7263-9150-50 Tel: [44]-(0)1242-227223 Units 7 & 8, Furlong Business Park, Bishops Cleeve, Gloucestershire GL52 8TW, U.K.

Table of Contents