Page 1
电源模块。交流电源模块和直流电源模块都可以将输入的电压转换成受电 设备所需要的 12V 电压,且其最大输出功率可达 180W。 • The PSR180-12A-F and PSR180-12A-B AC power supplies are similar in views except for their marks and airflow directions.The PSR180-12A-F power supply draws air from the power supply panel while the PSR180-12A-B and PSR180-12D-B power supplies exhausts air from the power supply panel.
Page 2
You can remove one of power modules in 1+1 redundancy while the device is operating. Before removing the power module, disconnect the power module Hot swappable from the external power supply system. 支持热插拔 在设备不断电的情况下,可先断开1+1冗余备份电源系统中某个电源模块与外 置供电系统的连接,然后直接对电源模块进行插拔操作 PSR180-12A-F、PSR180-12A-B、PSR180-12D-B Protection function Protection state Support for auto-recovery 具体保护功能 保护状态特征...
Page 3
• Connect the power cord to the external power supply system . 最后连接电源线至外置电源系统。 Technical specifications 电源模块规格 Item 项目 Specifications 规格 PSR180-12A-F/PSR180-12A-B:100 to 240V AC @ Rated voltage range 50/60Hz 输入额定电压范围 PSR180-12D-B:-48 to -60V DC PSR180-12A-F/PSR180-12A-B:90 to 264V AC @ Max voltage range 47/63Hz 输入最大电压范围...
Page 4
Never place the power supply in a wet area and prevent fluid from flowing into the power supply. 请不要将电源模块放置在潮湿的地方,也不要让液体进入电源模块。 • To avoid power supply damage, do not open the power supply. When the internal circuits or components of the power supply fail, contact H3C Support. 为了防止电源模块受损,请不要随意打开电源模块外壳,当电源模块内部 线路或元器件出现故障时, 请移交维修人员进行检修。 •...
Page 5
3. Installing the power supply 电源模块的安装 • To prevent damage to the power supply or the connector on the backplane of the powered device, insert the power supply gently. 为了避免损坏电源模块或受电设备背板的连接器端子,在电源模块插入过 程中动作要缓慢。 • If you insert the power supply upside down, you will encounter a hard resistance because of the special structure designs of the slot and power supply.
Page 6
4. Removing the power supply 电源模块的拆卸 (1) Disconnect the power cord from the power supply and the external power supply. 拆除电源线与电源模块和外置供电系统的连接。 (2) Face the front of the power supply. 操作者正对受电设备上要拆卸的电源模块。 (3) Use a Phillips screwdriver to loosen the captive screws on the power supply until the captive screws are disengaged from the device.
Page 7
(1) Attach the hooks of the power cord retainer clip into the holes on the two sides of the AC-input power receptacle.Skip this step if the power cord retainer clip is installed on the power supply. 将电源线防脱卡钩的两头分别插入交流电源输入 插口左侧的上下插孔中。若电源模块发货时已安装卡钩,请忽略此步。 (2) Pull the power cord retainer clip leftward. 将电源线防脱卡钩扳向左边。 (3) Connect one end of the AC power cord to the AC-input power receptacle.
Need help?
Do you have a question about the PSR180-12A and is the answer not in the manual?
Questions and answers