Protecting The Environment; Troubleshooting; Maintenance - Black & Decker BEHTS551 Manual

Table of Contents

Advertisement

Available languages

Available languages

  • ENGLISH, page 1
Fertilizers and other garden chemicals contain agents which
greatly accelerate the corrosion of metals. Do not store the
unit on or adjacent to fertilizers or chemicals.
Blade Lubrication (Fig. L)
After use, disconnect the power source.
u
Carefully apply a resin solvent to the exposed blades.
u
Connect the power source and turn the trimmer vertical
u
with the blades toward the ground and run the trimmer
for a few seconds to fully disperse the lubrication.
Keeping your hands away from the blade, slide the
u
sheath 10 over the blade until it snaps into place as
shown in Figure L.
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.

Maintenance

Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Lubrication oil is available from your BLACK+DECKER dealer
(cat. no. A6102-XJ).
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
After use, carefully clean the blades. After cleaning, apply
u
a film of light machine oil to prevent the blades from rust-
ing.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.

Protecting the environment

Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com

Troubleshooting

Problem
Slow running, noisy or
hot blades.
Unit will not start.
Autogoods "130"
Possible Cause
Possible Solution
Dry, corroded blades.
Lubricate blades.
Blades or blade support
Straighten blade or
bent.
blade support.
Bent or damaged teeth.
Straighten teeth.
Loose blade bolts.
Tighten blade bolts.
Lock off not fully
Check that lock off is
operated.
fully forward prior to
moving main trigger.
Cord not plugged in.
Plug cord into a work-
ing outlet.
Circuit fuse is blown.
Replace circuit fuse.
(If the product repeat-
edly causes the circuit
fuse to blow, discon-
tinue use immediately
and have it serviced
at a BLACK+DECKER
service center or
authorized servicer.)
Circuit breaker is
Reset circuit breaker.
tripped.
(If the product repeat-
edly causes the circuit
breaker to trip, discon-
tinue use immediately
and have it serviced
at a BLACK+DECKER
service center or
authorized servicer.)
Cord or switch is
Have cord or
damaged.
switch replaced at
BLACK+DECKER
Service Center or
Authorized Servicer.

Advertisement

Table of Contents
loading

Table of Contents