Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for DTS XR250 WASH
Summary of Contents for DTS XR250 WASH
- Page 1 XR250 XR250 d i v i s i d i v i s i S h o w S h o w...
- Page 2 DTS . DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di design a ciascun proprio prodotto. DTS non assume alcuna responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.
- Page 3 XR250 INDEX: 1- TECHNICAL FEATURES Pg. 1 2- IMPORTANT SAFETY INFORMATION Pg. 2 2.1 Fire prevention 2.2 Prevention of electric shock 2.3 Protection against ultraviolet radiation 2.4 Safety 2.5 Level of protection against the penetration of solid and liquid matter 3- MOUNTING THE LAMP Pg.
-
Page 4: Technical Features
XR250 1- TECHNICAL FEATURES - New motorized moving head - ABS cover - 150mm fresnel lens - MSD 250/2 lamp - Control: max 16 channels DMX - Fast, silent and precise movement - Position controlled pan (540°) and tilt (270°) by encoder - Motorized zoom (13°-23°) - Colour mixing by CMY - Colour wheel with 6 dichroic high chromatic yield filters +2 filters for... -
Page 5: Important Safety Information
- The level of technology inherent in the XR250WASH requires the assistance of specialised personnel for all servicing. Refer all work to your authorised DTS service centre. - A good earth connection is essential for proper functioning of the projector. -
Page 6: Mounting The Lamp
XR250 get as high as 350° C. Always check that the lamp is cold before attempting to remove it. In any case, only open the appliance 10 minutes after it has been turned off. 3- MOUNTING THE LAMP Warning: turn power off before opening the appliance. Philips MSD250/2 Power 250W Luminous flux 18.000 lm... -
Page 7: Voltage And Frequency
XR250 it as much as possible. 4- VOLTAGE AND FREQUENCY The projector can operate at 230V voltage, at 50 or 60 Hz. D.T.S. presets a voltage of 230V at a frequency of 50Hz (barring specific requests). 5- Installation XR7 may be either floor or ceiling mounted. For floor mounting installations, the XR7 is supplied with four rubber mounting feet (B) on the base. -
Page 8: Mains Connection
XR250 5.2 Protection against liquids The projector contains electric and electronic components which should under no circumstances come into contact with oil, water or any other liquid. The proper working of the unit would be compromised should this occur. 5.3 Movement The projector has a maximum movement of 540°... -
Page 9: Dmx Signal Connection
XR250 7- DMX SIGNAL CONNECTION The unit operates using a digital DMX 512 (1990) signal. Connection between the control box and the projector or between projectors must be carried out using a two pair screened ø0.5 mm cable and a CANNON XLR 5 or 3 pole connector Ensure that all conductors are isolated from one another and from the metal plug housing. -
Page 10: Dmx Addresses
XR250 8- DMX Addresses XR250WASH can be used in three different modes: 8, 10 or 14 DMX channels. If you want to use a DMX controller with 8 channels, select the 8 CH mode from the MODE menu and set the following addresses: Projector 1 A001 Projector 2 A009 If you want to select the next projector, just add “8”... -
Page 11: Display Panel
Changing the DTS default setting can vary the functions of the appliance so that it does not respond to the DMX 512 used to control it. Carefully follow the instructions below before carrying out any variations or selections. - Page 12 ENTER RESET T o reset all motors function MENU Up-Down ENTER ENTER DEFAULT T o restore default setting (set by DTS) MENU ENTER Up-Down Pcb 8 motors . Pcb PAN&TILT SOF TWARE VERSION Electronic card software version. MENU ENTER Up-Down...
- Page 13 XR250 Automatic operation (auto) XR7 can work in automatic mode without a DMX controller. First of all connect the projectors with a DMX cable (picture below). MASTER IN OUT IN OUT To activate Auto mode on the first unit, use the menu to run through the different modes until AUTO appears on the display, at this point press enter.
-
Page 14: Error Messages
XR250 The three new DMX channels are: -Scene channel Form 0-255 are displayed the programmable scenes (max 16 scenes M.001 M016) -View channel: -From 1-19 the unit runs the scene that has been saved in the units memory and it is possible to play through the other scenes using the scene channel. -
Page 15: Hidden Menu
XR250 10.2 Pan & Tilt speed (SPEE) (default: 2) You can set the PAN and TILT engines at high speed on your XR250WASH. Press menu until you see SPEE. Press ENTER and select a speed with UP-DOWN (there are 4 speeds). Confirm by pressing ENTER. - Page 16 XR250 Up-Down ENTER Up-Down ENTER ZOOM 1 ALIGNMENT To align zoom1 Up-Down ENTER Up-Down ENTER ZOOM 2 ALIGNMENT To align zoom 2 Up-Down ENTER Up-Down ENTER CYAN ALIGNMENT To align cyan colour Up-Down ENTER Up-Down ENTER MAGENTA ALIGNMENT To align magenta colour Up-Down ENTER Up-Down...
-
Page 17: Mechanical Parts
XR250 14.2 Fans and air passages The fans and air passages must be cleaned approximately every 6 weeks. This periodic cleaning will depend of course, on the conditions in which the projector is operating. Suitable instruments for performing this type of maintenance are a brush and a common vacuum cleaner or an air compressor. - Page 18 XR250 MOTOR ACTUATOR CARD DISPLAY (WHITE) ZOOM 1 (BLACK) MAGNETIC SENSORS YELLOW (WHITE) (DARK GREEN) STROBE (YELLOW) FROM J8 PAN & TILT COLOUR WHEEL (VIOLET) (PINK) EFFECTS FROM J10 (GREY) PAN & TILT (LIGHT GREEN) 30 VDC (RED) MAGENTA (LIGHT BLUE) CYAN (BLACK) (GOLD)
- Page 19 XR250 DISPLAY CARD IN LAMP FROM J4 8 MOTOR OUT LAMP ON/OFF LAMP CARD IF THE PCB DOESN’T WORK MOVE THE CABLE “IN LAMP” FROM Cn1 TO Cn7 TO DELETE ERROR FROM DISPLAY IN MENU SELECT CONECTOR RELAY CARD PAN & TILT CARD TILT 30 VDC (WHITE)
- Page 20 à à à à 'Ã8C6II@GÃHP9@à %Ãiv‡ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃà Ã8C6II@GÃHP9@Ãà %Ãiv‡Ãà 9@A6VGUÃT@UUDIBTà à à à à à à à DEFAULT COLOUR DEFAULT COLOUR COLOUR COLOUR MACRO CMY/COLOUR MACRO CMY/COLOUR DIMMER/ SHUTTER DIMMER/ SHUTTER PAN msb PAN msb TILT msb TILT msb EFFECT EFFECT ZOOM ZOOM PAN lsb...
- Page 21 à %( ' à à 8‚y‚ˆ…%à '! (&à à 7v8‚y‚ˆ…Ã%uv‡rà ('!à à Svtu‡Ã…h‡v‚ƃrrqà Àh‘à ! !"à à Svtu‡Ã…‚‡h‡v‚ƃrrqÃ!à !#!%à à Svtu‡Ã…h‡v‚ƃrrqÃ"à !&!(à à Svtu‡Ã…h‡v‚ƃrrqÃ#à ! ! !à à Svtu‡Ã…h‡v‚ƃrrqÃ$à ! "! $à à Svtu‡Ã…h‡v‚ƃrrqÃ%à ! %! 'à à Svtu‡Ã…h‡v‚ƃrrqÃ&à ! (!! à Ã...
- Page 22 à !%! $à ! à Ayh†uÃpy‚†rqƃrrqÃ!à ! %!!$à !!à Ayh†uÃpy‚†rqƃrrqÃ"à !!%!"$à !"à Ayh†uÃpy‚†rqƃrrqÃ#Àh‘à 8‚y‚ˆ…QhUvy‡Hhp…‚Ãvà !"%!#$à !#à 7yhpx‚ˆ‡Ã !#%!$$à !$à Pƒrà à à à DMX CHANNEL $à Parameter: ÃQ6IÀ†i DMX CHANNEL %à Parameter: ÃUDGUÀ†i DMX CHANNEL &à Parameter: Ã@AA@8U Move DMX range Mid point range Mode...
- Page 23 à à %Ã8C6II@GÃHP9@Ãà %iv‡Ãà PAN msb PAN lsb TILT msb TILT lsb SPEED MOVEMENT DIMMER SHUTTER COLOUR CYAN MAGENTA YELLOW SPEED CMY / DIMMER MACRO CMY / COLOUR EFFECTS ZOOM RESET DMX CHANNEL à Parameter: ÃQ6IÀ†i DMX CHANNEL !à Parameter: ÃQ6IÃy†i DMX CHANNEL "Ã...
- Page 24 à Move DMX range Mid point range Mode Option Function Value DMX value (degrees) (à à 7yhpx‚ˆ‡Ã Strobe random speed !"à à !#"&à à T‡…‚irƃrrqà Àv "'$ à à T‡…‚irƃrrqÃ!à $!%$à à T‡…‚irƃrrqÃ"à %%&(à à T‡…‚irƃrrqÃ#à '("à à T‡…‚irƃrrqÃ$à (# &à Ã...
- Page 25 à ! "! $à à Svtu‡Ã…‚‡h‡v‚ƃrrqÃ%à ! %! 'à à Svtu‡Ã…‚‡h‡v‚ƃrrqÃ&à ! (!! à à Svtu‡Ã…‚‡h‡v‚ƃrrqÃ'à !!!!!#à à Svtu‡Ã…‚‡h‡v‚ƃrrqÃ(Àvà !!$!!'à à T‡‚ƒÃ !!(!" à à Grs‡Ã…‚‡h‡v‚ƃrrqà Àvà !"!!"#à à Grs‡Ã…‚‡h‡v‚ƃrrqÃ!à !"$!"&à à Grs‡Ã…‚‡h‡v‚ƃrrqÃ"à !"'!#à à Grs‡Ã…‚‡h‡v‚ƃrrqÃ#à !# !#"à à Grs‡Ã…‚‡h‡v‚ƃrrqÃ$à !##!#%Ã...
- Page 26 à (degrees) (à I‚ÃAˆp‡v‚à !!$$à Hhp…‚à DMX CHANNEL #à Parameter: Ã@AA@8UT Move DMX range Mid point range Mode Option Function Value DMX value (degrees) (à #!à I‚Ãrssrp‡Ã !"(à !&à A…‚†‡Ã #!$$à ! "à 7rh€ÃTuhƒrà DMX CHANNEL $à Parameter: ÃaPPH Move DMX range...
Need help?
Do you have a question about the XR250 WASH and is the answer not in the manual?
Questions and answers