Washer Care; Cleaning Your Washer; Water Inlet Hoses; Vacation, Storage, And Moving Care - Whirlpool CABRIO W10240441A Use & Care Manual

Cleaning Your Washer

Washer Maintenance Procedure
This washer has a special cycle that uses higher water volumes, in
combination with AFFRESH
bleach, to thoroughly clean the inside of the washer.
NOTES:
■ Read these instructions completely before beginning the
cleaning process.
■
It is recommended that you allow the cleaning cycle to
complete without interruptions. If necessary, the cleaning
cycle may be interrupted by pressing the Power button once
or the Pause/Cancel button twice.
IMPORTANT: If the cleaning cycle is interrupted, run a Rinse &
Spin cycle to ensure that all remaining washer cleaner or bleach is
rinsed from the washer.
Begin procedure
1. Open the washer lid and remove all items from the washer.
2. Using the AFFRESH ® washer cleaner (recommended):
washer cleaner tablet to the washer
Add one AFFRESH ®
drum.
If using chlorine bleach:
Add 1 cup (250 mL) liquid chlorine bleach to the bleach
dispenser.
NOTE: Do not add any detergent to this cleaning cycle. Use of
more than 1 cup (250 mL) of bleach will cause product
damage over time.
3. Close the lid.
4. Press POWER.
5. Turn cycle control knob to CLEAN WASHER cycle.
■
The Estimated Time Remaining display will show
approximately 60 minutes.
6. Press START.
■
The cycle will begin and water will dispense in the washer for
a moment and pause, then the lid will lock and the cycle will
continue.
■
Once the cleaning cycle has begun, allow the cycle to
complete. An estimated cycle time will appear on the display.
■
If the procedure does not sufficiently improve the machine
freshness, evaluate your installation and usage conditions for
other causes.
Always do the following to maintain washer freshness
■ Use only High Efficiency (HE) detergent when washing a
clothes load.
Cleaning the exterior
Use a soft damp cloth or sponge to wipe up any spills.
Occasionally wipe the outside of your washer to keep it looking
new. Use mild soap and water. Do not use abrasive products.

Water Inlet Hoses

Replace inlet hoses after 5 years of use to reduce the risk of hose
failure. Periodically inspect and replace inlet hoses if bulges,
kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of replacement on
the label with a permanent marker.
12

WASHER CARE

® washer cleaner or liquid chlorine

Vacation, Storage, and Moving Care

Install and store your washer where it will not freeze. Because
some water may stay in the hoses, freezing can damage your
washer. If storing or moving your washer during freezing weather,
winterize it.
Non-use or vacation care:
Operate your washer only when you are at home. If you will be on
vacation or not using your washer for an extended period of time,
you should:
■ Unplug washer or disconnect power.
■
Turn off the water supply to the washer. This helps avoid
unintended flooding (due to a water pressure surge) while you
are away.
To winterize washer:
1. Shut off both water faucets.
2. Disconnect and drain water inlet hoses.
3. Put 1 qt (1 L) of R.V.-type antifreeze in the basket.
4. Run washer on the Rinse & Spin setting for about 30 seconds
to mix the antifreeze and remaining water.
5. Unplug washer or disconnect power.
To use washer again:
1. Flush water pipes and hoses. Reconnect water inlet hoses.
Turn on both water faucets.
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
2. Plug in washer or reconnect power.
3. Run the washer through the Bulky Items/Comforters cycle to
clean the washer and remove the antifreeze, if used. Use only
High Efficiency (HE) detergent. Use ½ the manufacturer's
recommended amount for a medium-size load.
To transport the washer:
1. Shut off both water faucets.
2. Disconnect and drain water inlet hoses.
3. If the washer will be moved during freezing weather, put 1 qt
(1 L) of R.V.-type antifreeze in the basket. Run washer on the
Rinse & Spin setting for about 30 seconds to mix the
antifreeze and remaining water.
4. Disconnect the drain from the drain system.
5. Unplug the power cord.
6. Place the inlet hoses into the basket.
7. Drape the power cord and drain hose over edge into the
basket.