Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Cirris CR
Summary of Contents for Cirris CR
- Page 1 User Manual Version 2018.2.0...
-
Page 2: Table Of Contents
Attaching the Installed Software to the Network Database Server ............5 Starting the Software ..........................6 Updating the Server Configuration ......................6 SETTING UP THE CR TESTER ..................7 Electrical Assembly ........................... 7 Installing Add-on Scanners ........................8 Installing more than 7 Add-on Scanners ....................10 CHECKING THE SYSTEM ................... -
Page 3: The Cr Tester
The CR Tester Introduction Use this guide to install the easy-wire software, setup the hardware, connect the CR tester to a network, and get the overview of the test system. Parts List Each CR order comes with the following parts: Base Scanner ... - Page 4 Cirris Systems | Installing Easy-Wire Software 2...
-
Page 5: Software Installation Guide
If you downloaded the software update from the Cirris internet site: 1. Use an unzip utility to open the downloaded zip file. 2. When prompted, enter the unzip password received from your Cirris support representative. 3. Be sure to note the path and folder where you extract the update files. -
Page 6: Use The Correct Installation Process
(located in the bottom right corner of the main menu) before proceeding. If your previously installed software version is from 2.0 to 6.5, call Cirris Technical Support before attempting to install the new version. If your previously installed software version is from 7.0 to 9.0, perform the steps in “Removing easy- ... -
Page 7: Installing The Software
4. If this is the first installation of the software, follow the prompts on the screen to complete the installation steps provided. 5. If you have installed anything other than the Cirris Server Software, proceed to the “Starting the Software” section because core files are generated during the first run of the software. If you have installed the Cirris Server Software, proceed to the “Updating the Server Configuration”... -
Page 8: Starting The Software
Note: If you have any problems with installing or updating your server software complete the following before contacting Cirris for support: 1. At the server, click Start, All Programs, Cirris Systems Corporation, Easy-Wire Server, Update Easy- Wire Cirris Server Configuration. -
Page 9: Setting Up The Cr Tester
Plug the power supply (latch side up) into the Base Scanner’s power connector. Latch side up Note: To remove the power supply, press down on the latch with your thumbnail and pull. Cirris Systems | Setting up the CR Tester 7... -
Page 10: Installing Add-On Scanners
If this is a multi-scanner system, see the following section. Then proceed to “Checking the System” on page 11. Terminators Installing Add-on Scanners Consider the information below before installing your add-on scanner(s). Cirris Systems | Setting up the CR Tester 8... - Page 11 200 ft (60m). 1. Connect an Add-on Cable between each box as shown. 2. Connect terminators to the two unused ports as shown. Terminators Add-On Cables Cirris Systems | Setting up the CR Tester 9...
-
Page 12: Installing More Than 7 Add-On Scanners
Chain the plug strips together to ensure To grounded consistant grounding. Don’t worry about wall outlet overloading power cords; a 125 scanner box system uses less than 200 watts of power. Cirris Systems | Setting up the CR Tester 10... -
Page 13: Checking The System
Enter the station name or server name (the station name will be used on reports generated by this station). Select easy-wire CR as the tester that will be attached to this station. Important! Make sure you select the correct tester. If you select the incorrect tester you can change testers by going to System Setup Options in Utilities. -
Page 14: Troubleshooting A Red Status Indicator
See the “Troubleshooting a Red Status Indicator” section below. For any other unresolved problems, see “Startup and Verify” in the easy-wire help system, or call Cirris Technical Support at 1-800-441-9910. Troubleshooting a Red Status Indicator... -
Page 15: Checking The Sound
“Completing a Network Install.” If you do not hear the sounds, continue with the steps below. From the easy-wire main menu, click Utilities. Click Setup System Options. Open the “Computer” tab and click Change Volume. Cirris Systems | Checking the System 13... - Page 16 Verify that the speakers are on and that the volume is turned up. • Verify that the volume on your PC is turned up (the PC volume control can be found on your windows task bar). If sound problems persist, call Cirris for assistance. Cirris Systems | Checking the System 14...
-
Page 17: Help
“Allow Blocked Content.” If there is no information bar, skip to step 4. 3. When this security warning appears, click Yes. Cirris Systems | Completing a Network Install 15... - Page 18 • Click Contact to view the contact information for all Cirris locations, reps, and distributors. • Click Website to view the Cirris website if your PC has an internet connection. Cirris Systems | Completing a Network Install 16...
-
Page 19: Gerneral Information
Cirris support personnel, you may need to send the affected module or the entire tester back to Cirris for repair. If needed during the repair period, a loaner tester can be sent to you. You should not attempt to service any circuit board at the component level. All component-level service should be performed by Cirris technicians. -
Page 20: Harness Board Demo
Harness Board Demo Depending on your application and needs, Cirris can provide you with a demo to introduce you to the basics of the Easy-Wire CR system. One demo focuses on Traditional Fixturing; another on easy- wire Adapter Fixturing, and another on Military Fixturing. To understand more about these fixturing types see the Fixturing Guide section included in this manual. -
Page 21: Warranty
Warranty Cirris Systems Corporation warrants the CR / CH+ analyzer to be free of defects in materials and workmanship for a period of one (1) year from the date of delivery to you, as evidenced by receipt of your warranty registration form. In the event a defect develops due to normal use during the warranty period, Cirris Systems will repair or replace the analyzer with a new or reconditioned unit of equal value. - Page 22 Cirris CR User Manual Version 2018.2.0 © 2016 Cirris Systems 401 North 5600 West Salt Lake City, Utah 84116 www.cirris.com...
Need help?
Do you have a question about the CR and is the answer not in the manual?
Questions and answers