Table of Contents
Advertisement
Quick Links
【Introduction】
IT-ES608-IM-4F is a type of WEB managed redundant Industrial Ethernet Switch, which support 4 10/100M Ethernet ports(RJ45), 4 100M fiber
ports, double power supply input and 1 route repay output. It supports SW-Ring patented technology (self-recovery time <20ms) to enhance the
reliability of the network. What's more, IT-ES608-IM-4F supports several network managements, such as 802.1QVLAN, QoS, IGMP, port trunkin g and
port mirroring. It has got the certification of CE, FCC and Industrial level 4 standard. It can meet the requirement of each type of industrial environment
with the temperature range of -40 to 75℃.
【Packing List】
The IT-ES608-IM-4F switch is shipped with following items.
IT-ES608-IM-4F Ethernet switch(Plus Terminal Block) ×1
Hardware Installation Guide ×1
CD-ROM with Windows Utility×1
Product Warranty Statement ×1
DIN-Rail setting fittings (wall mounting for optional)
【Features】
Specialized design for Industrial Application
Industrial Level 4 design, accord with IEC61850 standard
Dual power backup, reverse polarity protection
support double relay input warning for power failure and one alarm output
Port link, ring fault/abnormity alarm indication
IP 30 protection, rugged high-strength metal case
24VDC power input（12～48VDC）
-40～75℃ operating temperature range
DIN-Rail or panel mounting
IT-ES608-IM-4F
Industrial Ethernet Switch
Hardware Installation Guide
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Intellisystem IT-ES608-IM-4F
Summary of Contents for Intellisystem IT-ES608-IM-4F
- Page 1 【Introduction】 IT-ES608-IM-4F is a type of WEB managed redundant Industrial Ethernet Switch, which support 4 10/100M Ethernet ports(RJ45), 4 100M fiber ports, double power supply input and 1 route repay output. It supports SW-Ring patented technology (self-recovery time <20ms) to enhance the reliability of the network.
-
Page 2: Panel Layout
Port Trunking for optimum bandwidth utilization Port mirroring for online debugging Bandwidth management prevents unpredictable network status Lock port function for blocking unauthorized access based on MAC address 【Panel Layout】 IT-ES608-IM-4F Up panel Front panel Rear panel Top Panel Bottom Panel... -
Page 3: Relay Contact
The input terminal block is located in top panel of the device and it is also the contact of the device alarm. It is often off when no alarm happens, or it is turned on. IT-ES608-IM-4F supports 1 relay information output to connect alarm indicator or alarm buzzer to remind of operator in time in case of... -
Page 4: Power Input
【Power Input】 IT-ES608-IM-4F owns redundant power input, which provides two terminal blocks for PWR1 and PWR2 input. The redundant power can be used independently. PWR1 and PWR2 can supply power at the same time, once either of these two powers fails, another power can acts as backup automatically to ensure reliability of the network. - Page 5 MDI signal MDI-X signal — — 4、5、7、8 Note: “TX±”transmit data±, “RX±”receive data±, “—”not use MDI（straight-through cable） ： MDI-X（Cross-over cable） ： 100Base-FX port 100Base-FX full-duplex SM or MM port, SC/ST type .The fiber port must be used in pair, TX (transmit) port connect remote switch’s RX(receive) port; RX(receive) port connect remote switch’s TX(transmit) port.
-
Page 6: Led Indicators
【LED Indicators】 LED indicator light on the front panel of IT-ES608-IM-4F.the function of each LED is described in the table as below. System indication LED State Description Power 1 is working normally. PWR1 PWR1 is not connected or does not （green）... -
Page 7: Specifications
Insert the top of the DIN-Rail into the slot just below the stiff metal spring. The DIN-Rail attachment unit will snap into place as shown below. Wiring Requirements Wiring need to meet the following requirements: It is needed to check whether the type, quantity and specification of cable match the requirement before cable laying; It is needed to check the cable is damaged or not, factory records and quality assurance booklet before cable laying;... - Page 8 Interfaces： 100M Fiber port：100Base-FX，SC/ST optional 100M Ethernet Port：10Base-T/100Base-TX，RJ45，auto-flow control, full/half duplex mode and MDI/MDI-X auto-connection Console port：Based serial network management (RS-232), RJ45 Alarm output interface: One relay alarm output. Support power, port link and ring network alarm Current Carrying Capability: 1A@30VDC Processing type: Store and Forward System exchange bandwidth: 2.0G Cache：1Mbits...
- Page 9 Full load power: 6.1W@24VDC Support redundant protection Support reverse polarity protection Support overload current protection Environment： Operating Temperature：-40～75℃ Storage Temperature：-40～85℃ Relative Humidity: 5 to 95% (non-condensing) Mechanical Structure: Shell：IP30 protection, metal case Installation：DIN-rail mounting Weight：800g Dimensions（W×H×D） ：136 mm×52mm×105mm Approvals EMI：FCC Part 15，CISPR (EN55022) class A EMS：EN61000-4-2 (ESD)，Level 4 EN61000-4-3 (RS)，Level 3 EN61000-4-4 (EFT)，Level 4...
Need help?
Do you have a question about the IT-ES608-IM-4F and is the answer not in the manual?
Questions and answers