Table of Contents
Advertisement
Quick Links
TECHNICAL
TECHNICAL
T
T
E
L
E
E
L
Viking's K-202-DVA is a fully programmable two-input,
multi-number auto dialer, designed for emergency and
non-emergency message notification. The K-202-DVA
has two dry contact inputs, each of which can dial up to
seven 32-digit phone numbers and play a message up
to 1 minute in length specific to that input.
Messages can be recorded locally or remotely with a
total message time for both inputs of two minutes. The
K-202-DVA has call progress detection capability with
normal and fast busy, call pickup, CPC and ring-no-
answer detection. Programming is easily done with a
Touch Tone phone.
F
e
a
t
u
r
e
s
F
e
a
t
u
r
e
s
• Non-volatile memory (no batteries required)
• Stores up to seven 32-digit phone numbers per
input (fourteen 32-digit numbers total)
• 2 minutes of record time (1 minute per input)
• Programmable message repeat counter
• Programmable lap counter
• Two inputs programmable for normally open or normally
closed and enabled or disabled
• Programmable ring delay for remote programming and
alarm polling
• Programmable qualifier timer for each input (time
for an event to be qualified as an alarm)
• Programmable resume timer for each input (time
following reset for input to become active again)
• Call progress detection
• Programmable ringback limit for call progress
• Remote security and access codes
• Local or remote programming and recording
• Compatible with the RC-2A and RC-3 remote DTMF
controllers
• Phone numbers may be programmed as pager num-
bers (no voice message played)
• Programmable hookswitch flash before dialing
www.AlphaCommunications.com
S
S
C
O
M
O
L
U
T
I
O
N
E
C
O
M
O
L
U
T
I
O
N
Voice Alarm Dialing from Two Inputs
P
r
a
P
r
a
2
1
2
1
S
F
O
R
T
H
E
S
T
S
F
O
R
T
H
E
S
T
A
p
p
A
p
p
• Security/burglar/fire alarm notification
• System alarm or equipment malfunction notification
• Environmental warning notification
• Contacting personnel via numeric pagers
S
p
e
S
p
e
Power: 120V AC/12V DC 500 mA, UL listed adapter provided
Dimensions: 133mm x 91mm x 44mm (5.25" x 3.6" x 1.75")
Shipping Weight: 0.68 Kg (1.5 lbs)
Environmental: 0°C to 32°C (32°F to 90°F) with 5% to 95% non-
condensing humidity
Talk Battery: 12V DC
Touch Tone Dialing: 120 ms on/off, 50 ms on/off
CPC Detection Time: 320 ms minimum
Message Record Time: 2 minutes
Sampling Rate: 64 K (equivalent)
Input Detection Time: 80 ms with Qualifier Timer set to 0
Resolution Qualifier Timer: 1 second to 18 hours (see page 3)
Resolution Resume Timer: 1 second to 18 hours (see page 3)
Connections: (1) RJ11 jack for telco connection, (1) 4 position
screw terminal block for inputs
TAK-4202
Two-Input Voice
c
t
i
c
e
c
t
i
c
e
C
C
E
N
T
U
R
Y
E
N
T
U
R
Y
l
i
c
a
t
i
o
n
s
l
i
c
a
t
i
o
n
s
c
i
f
i
c
a
t
i
o
n
c
i
f
i
c
a
t
i
o
n
Alarm Dialer
October 30, 2008
s
s
Advertisement
Table of Contents
Related Manuals for Viking TAK-4202
Summary of Contents for Viking TAK-4202
- Page 1 Alarm Dialer October 30, 2008 Voice Alarm Dialing from Two Inputs Viking’s K-202-DVA is a fully programmable two-input, multi-number auto dialer, designed for emergency and non-emergency message notification. The K-202-DVA has two dry contact inputs, each of which can dial up to seven 32-digit phone numbers and play a message up to 1 minute in length specific to that input.
- Page 2 Viking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for a period of one year from the date of purchase from any authorized Viking distributor or 18 months from the...
- Page 3 Resume timer determines when an alarm input leaves the reset state. The default value of the Resume Timer is zero, which is OFF. Security Code: A six-digit code required for entering programming. 120V AC TAK-4202 MODEL K-202-DVA VIKING 12V DC...
- Page 4 A. Entering the Programming Mode 1. Local Step 1. Move the PROG/NORM switch to PROG and plug an analog phone into the TELCO jack. Step 2. After taking the phone off hook, wait for two beeps. Step 3. Program as shown in sections B-T. Step 4.
- Page 5 C. Factory Default Settings 845464 (V-I-K-I-N-G) (see section D) Enabled (see section I) Security Code Call Progress Detection Access Code 123456 (see section E) Alarm Input N/O (Enabled) Momentary Configuration (see section J) Phone Numbers Not programmed (see section N) Lap Counter 1 (see section K) Messages...
- Page 6 L. Qualifier Timer Enter 6 digits + #X , where X is the input number (1-2). The format is 2 digits for hours, 2 digits for minutes, and 2 digits for seconds: HHMMSS. The qualifier timer can be set anywhere from zero to 18 hours, and has a 1 second res- olution.
- Page 7 S. Playing Back Messages When in programming, enter 0 followed by the number of the input to play back the message recorded for that input. If no message has been recorded, nothing will be heard. T. Return to Default IMPORTANT: Executing the following programming erases all phone numbers and messages and returns the K-202-DVA to default settings.
- Page 8 Call (715) 386-4345 and select 485. Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
Need help?
Do you have a question about the TAK-4202 and is the answer not in the manual?
Questions and answers