Related Manuals for Kirsch Wood Blinds Tilt Automation III
Summary of Contents for Kirsch Wood Blinds Tilt Automation III
- Page 1 Wood Blinds Collection Tilt Automation III Installation Instructions Rev. C 5/3/22...
-
Page 2: Table Of Contents
GETTING STARTED CONTENTS GETTING STARTED ..........................1 Product View - Automation III ........................1 Tools and Fasteners Needed ........................2 Unpack the Blind ............................2 INSTALLATION ........................... 3 Installation Overview ..........................3 STEP 1 — Install the Brackets ........................3 Mount the Installation Brackets —... -
Page 3: Getting Started
GETTING STARTED Product View - Automation III Valance End Bracket Spacer Block Intermediate Bracket Bracket Spacer Block Intermediate Bracket (If Required) Transceiver Assembly 12V Battery Control 2" or 4" Wand Button Extension Brackets (Optional) Headrail Bracket Shim Valance Splice (Optional) (If Required) End Bracket Spacer Block... -
Page 4: Tools And Fasteners Needed
GETTING STARTED ® Thank you for purchasing the Kirsch Wood Blinds Collection. With proper installation, operation, and care, your new blinds will provide years of beauty and performance. Please thoroughly review this instruction booklet and the enclosed packing list before beginning the installation. -
Page 5: Installation
INSTALLATION INSTALLATION Installation Overview To install your blind, you will need to perform the following four steps STEP 1: Install the Brackets STEP 2: Connect the Power Cable STEP 3: Install the Blind STEP 4: Connect the Power Source, If Applicable Mounting Types and Window Terminology If the installation brackets are mounted correctly, the rest of the installation process follows easily. -
Page 6: Mount The Installation Brackets - Outside Mount
INSTALLATION INSTALLATION Attach the End Brackets With inside or ceiling mounts, attach the two end brackets flush against the sides of the window casement or to the ceiling. Choose the most appropriate of the following mounting methods: Side/Top Mount (Inside mount only): Mount the end ■... - Page 7 INSTALLATION INSTALLATION Attach the End Brackets Attach the end brackets using two screw through diagonal holes. ■ If using spacer blocks, use #6 screws long enough for a secure installation ➤ (2½” long screw is recommended). IMPORTANT: The tops of the end brackets must align. CAUTION: The rear of the end brackets or spacer blocks must be flush against a flat mounting surface.
-
Page 8: Step 2 - Connect The Battery Wand Or Rechargeable Battery Wand, If Applicable
INSTALLATION INSTALLATION STEP 2 — Connect the Battery Wand or Rechargeable Battery Wand, If Applicable NOTE: When power is connected to the motor, a blue LED inside the control button housing will flash to indicate the blind is ready for operation. Refer to the appropriate page based on your order. - Page 9 INSTALLATION INSTALLATION Attach the Magnetic Valance Clips to the Valance The magnetic valance clips are adjustable for quick and easy valance attachment and have multi-position valance adjustment capabilities. To install the clips, lay the valance face down on a protected surface with the back side up. ■...
-
Page 10: Step 4 - Connect The Power Source, If Applicable
For an optional rechargeable battery wand, see page 9. ➤ For an optional 18V DC Power Supply, see page 10. ➤ For an optional 18V DC Power Supply with daisy-chain connections, see page 10. ➤ ® For any other Kirsch power supplies, see applicable instructions. ➤... - Page 11 INSTALLATION INSTALLATION Satellite Battery Wand Mount the Satellite Battery Wand NOTE: Refer to this section only if a battery wand or satellite battery pack was included with theh blind. Wall Mount Bracket Decide where you want to attach the wall mount bracket. A satellite battery wand may be mounted in ■...
- Page 12 INSTALLATION INSTALLATION Insert the Rechargeable Battery Wand into the Battery Mount NOTE: The rechargeable battery wand ships fully charged, so it is ready to install out of the package. Match the direction of the arrow on the underside of the ■...
-
Page 13: Testing The Blind
INSTALLATION INSTALLATION Attach the Valance with Magnetic Valance Clips Align the valance to the headrail. ■ Hold the valance securely from the front side with both hands. ■ Position the clips to the top-front lip of the headrail until it is level and in position. ■... -
Page 14: Operation
INSTALLATION OPERATION Operate the Blind Raising and Lowering the Blind IMPORTANT: Whenever raising or lowering the blind, the slats must be in the open position. Pull the single cord down and toward the center to raise and lower. ■ Hold the single cord to the outside to lock the blind in position. ■... -
Page 15: Resetting The Blind (If Necessary)
The Automation App is required to program Automation III blinds, remotes, and gateways. The App is compatible with Apple® and Android™ smartphones and tablets. For more information regarding setup and operation using the Automation App, refer to https://www.kirsch.com/window-coverings-product-manuals. Automation III Gateway The Automation III Gateway is used to control blinds in larger projects as well as integrate Automation III blinds with third-party integration systems. -
Page 16: Troubleshooting
There are two methods for charging the rechargeable battery wand — the dual charging station or the single charger. CAUTION: The rechargeable battery wand can only be charged with these Kirsch provided charging options. Attempting to charge battery wands with an alternative charger may result in permanent damage. - Page 17 INSTALLATION TROUBLESHOOTING Problem Rechargeable battery needs recharging (continued). Solution Recharging Via the Dual Charging Station Plug the dual charging station into a standard AC outlet. ■ Insert the nose of the rechargeable battery wand into one of the slots of the dual ■...
- Page 18 INSTALLATION TROUBLESHOOTING Problem Decorative tapes are wrinkled after installation. Solution Use a steamer to steam out the wrinkles. Wave the steamer in front of the tapes for a few seconds. Do not touch the slats with the steamer. To avoid stretching the tapes, do not pull down on the bottom rail while steaming. Problem When hanging, the slat pack appears to be skewed toward the cordlock side of the unit, particularly in an inside mount installation.
-
Page 19: Care
A Note About Wood Products Kirsch Wood Blinds Collection are true wood products, made from 100% hardwood. There will be variations in color, grain, and texture that are characteristics of all woods. These variations will be especially visible in blinds with light color stains. The variations... -
Page 20: Child Safety
INSTALLATION CHILD SAFETY... -
Page 21: Declarations
Kirsch®, One Duette Way, Broomfield, CO 80020, USA Kirsch® hereby declares that the PV40 is in compliance with the essential requirements and other relevant provisions of Electromagnetic Compatibility (EMC) Directive 2014/30/EU and Radio Equipment Directive (RED) 2014/53/EU. A copy of the DoC can be obtained online:... -
Page 22: Warranty
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. © 2020 Kirsch Custom Window Coverings. All rights reserved. All trademarks used herein are the property of Kirsch or their respective owners. 07/20...
Need help?
Do you have a question about the Wood Blinds Tilt Automation III and is the answer not in the manual?
Questions and answers