Download Print this page

Jobsite V-12/AW Installation And User Manual

12-step all weather wall mount volume control.
Hide thumbs


For Precise Volume
Adjustment in All
Weather Conditions


   Also See for Jobsite V-12/AW

   Related Manuals for Jobsite V-12/AW

   Summary of Contents for Jobsite V-12/AW

  • Page 1

    INSTALLATION & USER GUIDE For Precise Volume Adjustment in All Weather Conditions V-12/AW 12-STEP ALL WEATHER WALL MOUNT VOLUME CONTROL...

  • Page 2: Table Of Contents

    V-12/AW 12-STEP ALL WEATHER WALL MOUNT VOLUME CONTROL TABLE OF CONTENTS Features...1 Product Overview...2 Package Contents ...3 Preparing for Installation...3 Installation...4 Operation...6 Specifications ...7 Warranty...8...

  • Page 3: Features

    FEATURES Includes standard faceplate Includes weather resistant gasket and stainless steel hardware Safely connect up to eight speaker pairs to a single amplifier or receiver UL listed to comply with local building codes Stylish indicator knob 12-step make before break volume control switch design Installation friendly design: Accepts up to 14-gauge wire Snap and lock connector secures wire in place without the use of a screwdriver...

  • Page 4: Product Overview

    PRODUCT OVERVIEW V-12/AW Figure 1 (a) Knob (b) Faceplate (c) Gasket (d) Volume Control...

  • Page 5: Package Contents

    Gasket x 1 Figure 2 PREPARING FOR INSTALLATION If you are installing the V-12/AW into an existing wall, take time to consider any possible obstructions which may be hidden inside the wall, such as wood or metal studs, electrical, telephone or other types of wiring, plumbing, AC or heating conduit.

  • Page 6: Installation

    IM controls with such a selector will reduce your maximum volume substantially. To solve this problem, specify a speaker selector with a defeatable protection circuit (JobSite models S-4 or S-6). Then keep the protection circuit off at all times. Tools Required 1/8"...

  • Page 7

    6. Insert the smooth side of the connector plug into the smooth side of the V-12/AW socket. 7. Install the V-12/AW into the device ring. 8. Set the Impedance Magnification Switch as determined by the impedance charts. 9. Set the switches, on all of the controls, to the same position (1x, 2x, 4x, or 8x).

  • Page 8: Operation

    2. Set the volume on the volume control to maximum (fully clockwise). 3. If you are using a JobSite speaker-selection system, locate the on/off button that corresponds to the speaker pair you wish to play. Set it to the ON position.

  • Page 9: Specifications

    SPECIFICATIONS High power rating: 100 watts per channel RMS, 200 watts peak Adjustable impedance: 1x, 2x, 4x, 8x settings Total attenuation: 54dB maximum Wiring requirements: 2 individual runs of 2-conductor 14-18-gauge speaker wire or 1 run of 4 conductor. V-T8 volume control connection terminal recommended Mounting: Fits most single gang junction boxes, weather...

  • Page 10: Warranty

    This Warranty is subject to the following additional conditions and limitations. The Warranty is void and inapplicable if JOBSITE deems that the product has been used or handled other than in accordance with the instructions provided by the manufacturer,...

  • Page 11

    If the above conditions are met, the purchaser’s sole remedy shall be to return the product to JOBSITE, in which case JOBSITE will repair or replace, at its sole option, the defective product without charge for parts or labor. JOBSITE will...

  • Page 12

    WWW.JOBSITESYSTEMS.COM © 2004 JobSite Systems. All rights reserved. JobSite, Pure Custom and Niles are registered trademarks of Niles Audio Corporation and the JobSite Logo is a trademark of Niles Audio Corporation. All other trademarks are the property of their respective owners. Some JobSite products (or components thereof) are manufactured under one or more U.S.

Comments to this Manuals

Symbols: 0
Latest comments: