Table of Contents
Advertisement
Timer Recording
Up to 8 timer recording programs can be made using G-
/
CODE
S
V
timer programing or Express timer programing method
HOW
IEW
as far as a year in advance. Remember, the clock must be set
before you can program the timer.
NOTES:
● If all the 8 programs have already been set, “PROGRAM FULL”
appears on the TV screen.
● After timer recording is completed, the recorder turns off
automatically.
● You can program the timer recording while a regular recording
is in progress; the menu screens will not be recorded.
● In case of a power failure after programming, the recorder’s
memory backup keeps your selections (if the lithium battery is
not exhausted).
TM
TM
G-
/S
V
System Setup
CODE
HOW
IEW
INFORMATION
G-
and S
V
are different trademarks used to represent
CODE
HOW
IEW
the same easy recording feature, but only the term G-
system
CODE
will be used in the instructions. If you use the S
V
system,
HOW
IEW
follow the same instructions listed for the G-
system.
CODE
The G-
timer programming system eliminates the need to
CODE
input channel, date, start and stop time data when setting the
timer record function. Simply key in the G-
number for the
CODE
TV programme you wish to record (found in most TV listings) and
the recorder's timer is automatically programmed.
You have to set “GUIDE PROG” numbers, which are assigned to
each station for purposes of G-
timer programming, for all
CODE
the stations stored in your recorder’s memory to get proper results.
Before G-
setup you must have performed the procedures of
CODE
Tuner Set and Clock Set.
IMPORTANT
Perform the following procedure after Auto Set Up and/or the
channel setting steps.
After setting the Guide Program Numbers, channel positions may
be incorrect if you stored or skipped channels. In this case, re-
perform Guide Program Number setting.
Guide Program Number Set
A
Access Main Menu screen, then Initial Set screen
Press MENU on the remote control. Press PUSH JOG rt to place
the pointer next to “INITIAL SET”, then press OK or PUSH JOG e.
B
Access G-
/S
V
Setup screen
CODE
HOW
IEW
Press PUSH JOG rt to place the pointer next to “G-CODE/
SHOWVIEW SETUP”, then press OK or PUSH JOG e.
C
Input Guide Prog number
G-CODE/SHOWVIEW SETUP
Press PUSH JOG rt or the Number
GUIDE PROG
TV PROG
keys to select the Guide Program
2
5
number as shown in the TV listing, then
press OK or PUSH JOG e.
[0-9] OR [R/T]: SELECT
[MENU] : EXIT
D
Input receiving channel number
G-CODE/SHOWVIEW SETUP
Press PUSH JOG rt or the Number
GUIDE PROG
TV PROG
keys to select the number of the channel
2
2
on which the Guide Program number’s
broadcasts are received, then press OK
[0-9] OR [R/T]: SELECT
or PUSH JOG e.
[MENU] : EXIT
● If the satellite broadcast is received on
your recorder's auxiliary channel (“L-1” or “F-1”), select “L-1”
or “F-1” for the channel position to which the satellite receiver is
connected.
● Repeat steps 3 3 3 3 and 4 4 4 4 as necessary.
E
Return to normal screen
Press MENU on the remote control.
TM
TM
G-
/S
V
Timer Programming
CODE
HOW
IEW
Before performing G-
/S
V
Timer Programming:
CODE
HOW
IEW
● Be sure to read “G-
TM
TM
/S
V
System Setup”
CODE
HOW
IEW
(
10).
● Insert a cassette with the safety tab in place. The recorder will
come on automatically.
● Turn on the TV and select the VIDEO channel (or AV mode).
● Select the appropriate colour system (
15).
With the G-
system , timer programming is greatly simplified
CODE
because each TV programme has a corresponding code number
which your recorder is able to recognise.
A
Access G-CODE/SHOWVIEW NO.
G-CODE/SHOWVIEW NO.
screen
Press PROG.
[0-9]
[+/–] : EXPRESS PROGRAMING
[PROG] : EXIT
B
Enter G-
number
CODE
G-CODE/SHOWVIEW NO.
Press the number keys to enter the
1 2 3 4 5 6 7 8
G-
number of a programme you
CODE
wish to record.
● If you make a mistake, press & and
[0-9]
[&] : DELETE
input the correct number.
[PROG] : EXIT
C
Enter G-
programme screen
CODE
– PI –
Press OK, and the G-
Programme
NO. 123456789
CODE
START
STOP
screen appears. (If you're just starting
21:00
22:00
out, “P1” appears.)
SP
DATE
TV PROG
25.04
1
: OK
[1] : TITLE
IMPORTANT
Make sure the channel position number you wish to record is
TM
TM
displayed; if not, see “G-
/S
V
System Setup” on
CODE
HOW
IEW
page 10 and set the Guide Program number for that G-
CODE
number correctly.
● If the number you entered is invalid, “ERROR” appears on the
screen. Press & and input a valid G-
number.
CODE
● If the “G-CODE/SHOWVIEW SETUP” screen appears, see
“ATTENTION – Regarding Guide Program Number Set”
on page 11.
D
Set tape speed
Press p to set the tape speed.
E
Access title edit screen
– P1 –
Press the number keys “1”. The Title Edit
screen appears.
25.04
21:00 PR.1
● You can access the Title Edit screen
[0-9] : SELECT LETTERS
only when “PROG. NAVIGATION” is
[&] : DELETE
[Y/U] : CURSOR
set to “ON”. (
15)
: OK
[PROG] : EXIT
F
Enter programme title
– P1 –
Press the number keys and PUSH JOG e
to enter characters, then press OK. For
25.04
W
details, refer to “Entering Character” on
[0-9] : SELECT LETTERS
page 14.
[&] : DELETE
[Y/U] : CURSOR
G
Return to normal screen
: OK
[PROG] : EXIT
Press PROG or OK. “PROGRAM
COMPLETED” appears on the screen for about 5 seconds, then
normal screen appears. If “PROGRAM OVERLAPPED” appears on
the screen and “Err” on the display panel, see page 13.
● Repeat steps 1 – 7 for each additional programme.
H
Engage recorder’s timer mode
Press #. The recorder turns off automatically and “#” appears on
the display panel.
● To disengage the timer, press # again.
Page 10
Advertisement
Table of Contents
