Related Manuals for SHOWTEC Accent Spot SW
Summary of Contents for SHOWTEC Accent Spot SW
- Page 1 USER MANUAL ENGLISH Accent Spot SW Product code: 42542 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
- Page 2 Accent Spot SW Preface Thank you for purchasing this Showtec product. The purpose of this user manual is to provide instructions for the correct and safe use of this product. Keep the user manual for future reference as it is an integral part of the product. The user manual shall be stored at an easily accessible location.
-
Page 3: Table Of Contents
Accent Spot SW Table of contents Introduction ................................4 Before Using the Product ..........................4 Intended Use ............................... 4 Product Lifespan ..............................4 LEDs Lifespan ............................... 4 Text Conventions ..............................4 Symbols and Signal Words ..........................5 Symbols on the Information Label ........................5 Safety .................................. - Page 4 Accent Spot SW Selecting Dimming Curves .......................27 Setting Dimmer Speed ........................28 Setting PWM Frequency ........................28 DMX Failure Settings ...........................28 DMX Synchronization .........................29 Display Lock ............................29 Restoring Factory Settings .........................29 Device Information.............................30 DMX Channels ..............................30 RDM Information ...............................31 RDM Details ..............................31 Supported RDM PIDs for the Device .......................31...
-
Page 5: Introduction
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your Highlite International dealer. Your shipment includes: ● Showtec Accent Spot SW ● Schuko to Power Pro cable (1,8 m) ● Beamshaper 10°... -
Page 6: Symbols And Signal Words
Accent Spot SW Symbols and Signal Words Safety notes and warnings are indicated throughout the user manual by safety signs. Always follow the instructions provided in this user manual. Indicates an imminently hazardous situation which, if not avoided, will result in DANGER death or serious injury. -
Page 7: Safety
Accent Spot SW Safety Important Read and follow the instructions in this user manual before installing, operating or servicing this product. The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual. Warnings and Safety Instructions... - Page 8 Accent Spot SW WARNING Risk of epileptic shock Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons should avoid looking at strobe lights. Attention Power supply ● Before connecting the device to the power supply, make sure that the current, voltage and frequency match the input voltage, current and frequency specified on the information label on the device.
-
Page 9: Requirements For The User
Accent Spot SW Attention Before each use, examine the device visually for any defects. Make sure that: ● All screws used for installing the device or parts of the device are tightly fastened and are not corroded. ● The safety devices are not damaged. -
Page 10: Description Of The Device
Description of the Device The Showtec Accent Spot SW is a compact indoor spot effect. It can be used for accent lighting. The device is delivered with 2 beamshapers (10° and 40°). The device can be used in many applications, both in rental and fixed installations. -
Page 11: Product Specifications
Accent Spot SW Product Specifications Model: Accent Spot SW Electrical: Input voltage: 100–240 V AC, 50/60 Hz Power consumption: 21 W Physical: Dimensions: 245 x 160 x 105 mm (L x W x H) Weight: 1,7 kg Optics: Light source:... -
Page 12: Optional Accessories
Accent Spot SW Optional Accessories The device is delivered with the following accessories: ● Product code: 42545 (Beamshaper for Accent Spot Q4/SW (10°) ● Product code: 42547 (Beamshaper for Accent Spot Q4/SW (40°) You can additionally purchase the following accessories: ●... -
Page 13: Rigging
Accent Spot SW Rigging The device can be mounted to a truss or other rigging structure in any orientation. Make sure that all loads are within the pre-determined limits of the supporting structure. CAUTION Restrict the access under the work area during rigging and/or derigging. -
Page 14: Angle Adjustment
Accent Spot SW Angle Adjustment You can adjust the angle of the device with the 2 adjustment screws (02). 01) Turn the 2 adjustment screws (02) counterclockwise to release them. 02) Tilt the device to the desired angle (see Fig. 06). -
Page 15: Connecting To Power Supply
Accent Spot SW Connecting to Power Supply DANGER Electric shock caused by short-circuit The device accepts AC mains power at 100–240 V and 50/60 Hz. Do not supply power at any other voltage or frequency to the device. This device falls under IEC protection class I. Make sure that the device is always electrically connected to the ground (earth). -
Page 16: Setup
Disconnect power supply before connecting or disconnecting data cables. Stand-alone Setup When the Accent Spot SW is not connected to a controller or to other devices, it functions as a stand- alone device. It can be operated manually. For more information about the control modes, refer to 6.2. Control Modes on page 18. -
Page 17: Dmx Cables
Fig. 08. Fig. 08 Master/Slave Setup The Accent Spot SW supports master/slave control mode. To connect multiple devices in master/slave setup, follow the steps below: Connect the first device’s DMX OUT connector to the second device’s DMX IN connector. -
Page 18: Dmx Linking
04) Continue assigning the starting addresses of the remaining devices by adding each time 10 to the previous number. Make sure that you do not have any overlapping channels in order to control each Accent Spot SW correctly. If two or more devices are addressed similarly, they will work similarly. -
Page 19: Operation
Control Modes The Accent Spot SW can be operated with a DMX controller and as a stand-alone device. The Accent Spot SW supports the following control modes: ●... -
Page 20: Control Panel
Accent Spot SW To operate multiple devices in the master/slave mode: 01) Use the first device as a master and use the remaining devices as slaves. See 6.6.5. Slave Mode on page 26 for more information. 02) Operate the master device in the Auto mode, Manual mode, Built-in Programs mode or the Sound- controlled mode. -
Page 21: Start-Up
Accent Spot SW Start-up Upon start-up, the display will show a splash screen with the software version and current temperature of the device. Immediately afterwards, the display will show the start screen (if the device is locked) or the main menu (if the device is unlocked). -
Page 22: Menu Overview
Accent Spot SW Menu Overview Product code: 42542... - Page 23 Accent Spot SW Product code: 42542...
-
Page 24: Main Menu Options
Accent Spot SW Main Menu Options 01) Press the UP/DOWN buttons to select one of the following options: ● 1. DMX ● 2. Manual ● 3. Auto ● 4. Program ● 5. Slave ● 6. Sound ● 7. Settings ●... -
Page 25: Dmx Channel Mode
Accent Spot SW DMX Channel Mode In this submenu you can select the DMX channel mode. 01) Press the UP/DOWN buttons to select the desired DMX channel mode. There are 3 options available: ● 3-channel mode ● 5-channel mode ●... -
Page 26: Program Mode
Accent Spot SW Program Mode In this menu you can run the 7 built-in programs. 01) Press the UP/DOWN buttons to select MODE: 02) Press the SETUP button to confirm the selection. 03) Press the UP/DOWN buttons to select one of the 7 available built-in programs: ●... -
Page 27: Program 2-7
Accent Spot SW Program 2–7 In these built-in programs you can set the program speed and add the strobe effect. 01) Press the UP/DOWN buttons to select SPEED: 02) Press the SETUP button to confirm the selection. 03) Press the UP/DOWN buttons to set the program speed. The adjustment range is 1–100, from slow to fast. -
Page 28: Settings
Accent Spot SW Settings In this menu you can adjust the settings of the device. 01) Press the UP/DOWN buttons to select one of the 7 options. The available options are: ● 1. Curves Select: See 6.6.7.1. Selecting Dimming Curves ●... -
Page 29: Setting Dimmer Speed
Accent Spot SW Setting Dimmer Speed In this submenu you can set the dimmer speed. 01) Press the UP/DOWN buttons to choose one of the 2 options: ● Fast: Light output will follow DMX dimmer value directly ● Smooth: Light output will follow DMX dimmer value with fade time to create smooth transitions 02) Press the SETUP button to confirm the selection. -
Page 30: Dmx Synchronization
Accent Spot SW DMX Synchronization In this submenu you can determine behavior of the device, when using multiple Accent Spots in the master/slave mode. 01) Press the UP/DOWN buttons to choose between ON and OFF. If you choose ON, the device will perform the same action as the other connected devices, without delays. -
Page 31: Device Information
Accent Spot SW Device Information In this menu you can view the firmware version, the temperature of the LEDs, the total operating hours and the ID of the device. ● Version: Shows the current firmware version ● Temperature: Shows the current temperature of the LEDs ●... -
Page 32: Rdm Information
Accent Spot SW RDM Information This device supports RDM. Refer to 6.9.2. Supported RDM PIDs for the Device for more information. RDM Details ● Responder ID: 29B4:09AXXXXX ● Manufacturer's ID: Showtec (Highlite International B.V.) ● Manufacturer Label: Showtec ● Model Description: Accent Spot SW ●... -
Page 33: Troubleshooting
Accent Spot SW Troubleshooting This troubleshooting guide contains solutions to problems which can be carried out by an ordinary person. The device does not contain user-serviceable parts. Unauthorized modifications to the device will render the warranty void. Such modifications may result in injuries and material damage. -
Page 34: Preventive Maintenance
Accent Spot SW Preventive Maintenance Attention Before each use, examine the device visually for any defects. Make sure that: ● All screws used for installing the device or parts of the device are tightly fastened and are not corroded. ●... -
Page 35: Deinstallation, Transportation And Storage
Accent Spot SW Deinstallation, Transportation and Storage Instructions for Deinstallation WARNING Incorrect deinstallation can cause serious injuries and damage of property. ● Let the device cool down before dismounting. ● Disconnect power supply before deinstallation. ● Always observe the national and site-specific regulations during deinstallation and derigging of the device. - Page 36 ©2022 Showtec...
Need help?
Do you have a question about the Accent Spot SW and is the answer not in the manual?
Questions and answers